Rhamnolipid produced from agroindustrial wastes enhances hydrocarbon biodegradation in contaminated soil

A crude biosurfactant solution was produced by Pseudomonas aeruginosa growing on agroindustrial wastes as the substrate and used to study its effect on hydrocarbon biodegradation by the indigenous soil microflora under laboratory conditions. Two concentrations were studied at first and 1 mg of biosurfactant/g of soil showed to be the most efficient for the total petroleum hydrocarbon reduction, which reached 85% at the first 20 days in soil microcosms. Respirometric and microbial analyses showed that the biosurfactant added did not have toxic effects over the microbial population. The use of a biosurfactant for bioremediation has been limited because of its high cost production. Biosurfactants produced from cost-free by-products combines waste minimization with economic potential bioremediation process.

Construction and demolition waste as a source of PVC for recycling

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Elaboration of sausage using minced fish of Nile tilapia filleting waste

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Digestive and functional properties of a partially hydrolyzed cassava solid waste with high insoluble fiber concentration

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Applicability of the use of waste from different banana cultivars for the cultivation of the oyster mushroom

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Loss minimization by the predictor-corrector modified barrier approach

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Case study: a 3D resistivity and induced polarization imaging from downstream a waste disposal site in Brazil

A contaminated site from a downstream municipal solid waste disposal site in Brazil was investigated by using a 3D resistivity and induced polarization (IP) imaging technique. This investigation purpose was to detect and delineate contamination plume produced by wastes. The area was selected based on previous geophysical investigations, and chemical analyses carried out in the site, indicating the presence of a contamination plume in the area. Resistivity model has successfully imaged waste presence (rho < 20 Omega m), water table depth, and groundwater flow direction. A conductive anomaly (rho < 20 Omega m) outside wastes placement was interpreted as a contamination plume. Chargeability model was also able to imaging waste presence (m > 31 mV/V), water table depth, and groundwater flow direction. A higher chargeability zone (m > 31 mV/V) outside wastes placement and following conductive anomaly was interpreted as a contamination plume. Normalized chargeability (MN = m/rho) confirmed polarizable zone, which could be an effect of a salinity increase (contamination plume), and the clay presence in the environment.

Interpretation of Resistivity Piezocone Tests in a Contaminated Municipal Solid Waste Disposal Site

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

PET containers in Brazil: Opportunities and challenges of a logistics model for post-consumer waste recycling

The use of post-consumer materials is directly related to reducing the cost of production and extraction of natural resources. Non-recyclable materials are randomly disposed in the environment. Brazil is one of the largest consumers of PET (polyethylene terephthalate) bottles. The purpose of this paper is to describe the opportunities and challenges of the logistics model for post-consumer PET bottle recycling in Brazil, while providing knowledge of its practices along the recycling chain. The results describe the need to educate those directly and indirectly involved in the process: to reduce consumption in order to reduce the amount of waste generated: to structure the post-consumer reverse chain and engage industrial sectors and government, through public policies, to support cleaner technologies along the PET bottle production chain. (C) 2010 Elsevier B.V. All rights reserved.

GREEN MACHINING ORIENTED TO DIMINISH DENSITY GRADIENT FOR MINIMIZATION of DISTORTION IN ADVANCED CERAMICS

After sintering advanced ceramics, there are invariably distortions, caused in large part by the heterogeneous distribution of density gradients along the compacted piece. To correct distortions, machining is generally used to manufacture pieces within dimensional and geometric tolerances. Hence, narrow material removal limit conditions are applied, which minimize the generation of damage. Another alternative is machining the compacted piece before sintering, called the green ceramic stage, which allows machining without damage to mechanical strength. Since the greatest concentration of density gradients is located in the outer-most layers of the compacted piece, this study investigated the removal of different allowance values by means of green machining. The output variables are distortion after sintering, tool wear, cutting force, and the surface roughness of the green ceramics and the sintered ones. The following results have been noted: less distortion is verified in the sintered piece after 1mm allowance removal; and the higher the tool wear the worse the surface roughness of both green and sintered pieces.

Optimisation of environmental gas cleaning routes for solid wastes cogeneration systems. Part II - Analysis of waste incineration combined gas/steam cycle

In the first paper of this paper (Part I), conditions were presented for the gas cleaning technological route for environomic optimisation of a cogeneration system based in a thermal cycle with municipal solid waste incineration. In this second part, an environomic analysis is presented of a cogeneration system comprising a combined cycle composed of a gas cycle burning natural gas with a heat recovery steam generator with no supplementary burning and a steam cycle burning municipal solid wastes (MSW) to which will be added a pure back pressure steam turbine (another one) of pure condensation. This analysis aims to select, concerning some scenarios, the best atmospheric pollutant emission control routes (rc) according to the investment cost minimisation, operation and social damage criteria. In this study, a comparison is also performed with the results obtained in the Case Study presented in Part I. (c) 2007 Elsevier Ltd. All rights reserved.

Optimisation of environmental gas cleaning routes for solid wastes cogeneration systems - Part I - Analysis of waste incineration steam cycle

Research of advanced technologies for energy generation contemplates a series of alternatives that are introduced both in the investigation of new energy sources and in the improvement and/or development of new components and systems. Even though significant reductions are observed in the amount of emissions, the proposed alternatives require the use of exhaust gases cleaning systems. The results of environmental analyses based on two configurations proposed for urban waste incineration are presented in this paper; the annexation of integer (Boolean) variables to the environomic model makes it possible to define the best gas cleaning routes based on exergetic cost minimisation criteria. In this first part, the results for steam cogeneration system analysis associated with the incineration of municipal solid wastes (MSW) is presented. (c) 2007 Elsevier Ltd. All rights reserved.

The minimization of open stacks problem: A review of some properties and their use in pre-processing operations

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A geometric interpretation for transmission real losses minimization through the optimal power flow and its influence on voltage collapse

This work presents an approach for geometric solution of an optimal power flow (OPF) problem for a two bus system (a slack and a PV busses). Additionally, the geometric relationship between the losses minimization and the increase of the reactive margin and, therefore, the maximum loading point, is shown. The algebraic equations for the calculation of the Lagrange multipliers and for the minimum losses value are obtained. These equations are used to validate the results obtained using an OPF program. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Banana Peel Applied to the Solid Phase Extraction of Copper and Lead from River Water: Preconcentration of Metal Ions with a Fruit Waste

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)