Influences of the load centre of gravity on heavy vehicle acceleration

The aim of this paper is to analyse the influence of the load centre of gravity on heavy vehicle acceleration. This analysis is done through a method in which a vehicle centre of gravity map is used. A model for the driving force is presented for bus, truck and tractor-semi trailer combinations. The proposed model takes into consideration the resistance forces (drag, rolling resistance, translation and rotation acceleration, climbing resistance) and the 4 X 2 traction system. The positions of the vehicle centre of gravity as a function of the position of the load centre of gravity are determined. The vehicle acceleration is calculated based on the position of the load centre of gravity. This study analyses the acceleration of one of the Mercedes-Benz do Brasil tractor-semitrailer vehicle. A comparison of the acceleration for different maximum adhesion coefficients and ramps are presented, showing new results. An example showing the variations of the load centre of gravity position with the acceleration time and distance is provided. The load centre of gravity position is important for vehicle safety and the efficiency and economy in the transportation of the load.

Effects of the season of the year, truck type and location on truck on skin bruises and meat quality in pigs

The purpose of this study was to evaluate the effect of the season of the year (summer vs winter), type of truck (A: single decker vs B : double-decker) and pig location on the truck (front, middle, rear) on the incidence of skin bruising and pork quality variation. For this purpose, 2660 gilts of an average weight of 126.7 (+/- 6.6) kg originating from 19 different farms were used. No interaction between season of the year, type of truck and location on truck was observed. A higher number of bruises on the body at unloading and slaughter (P < 0.0001) and a higher number of bruises on the carcass (P < 0.01) were observed in winter. At unloading a higher number of bruises on the body and on the carcass after slaughter was observed in pigs transported on Truck A (P=0.004 and P=0.05). A higher, although not significant, number of bruises was found on the body of pigs transported in the rear compartment of both trucks. Higher paleness value was found in the longissimus and semimembranosus muscles in summer (P=0.0001) than in winter. Cold and heat stress have a negative influence on skin bruises and meat quality, respectively. Poor vehicle design increases the incidence of bruised carcasses without detracting from pork quality regardless of the climate conditions tested and location of the animal it] the truck. (c) 2006 Elsevier B.V. All rights reserved.

An Intelligent Controller Design for Magnetorheological Damper Based on a Quarter-car Model

This paper presents the control strategies of nonlinear vehicle suspension using a magnetorheological (MR) damper. We used two different approaches for modeling and control of the mechanical and electrical parts of the suspension systems with the MR damper. First, we have formulated and resolved the control problem in order to design the linear feedback dumping force controller for a nonlinear suspension system. Then the values of the control dumping force functions were transformed into electrical control signals by the application of a fuzzy logic control method. The numerical simulations were provided in order to show the effectiveness of this method for the semi-active control of the quarter-car suspension.

Considerations in light truck suspension design

The present work aims at to approach considerations of trucks suspension design. The proposal of the work consists of discussing the aspects related to the acting of the suspension and of factors that interact with the system through representative models of the dynamic behaviour of the vehicle ride when operating in total load and/or empty conditions. The importance of this work is to revise some procedures of suspension study in the sense of adapting them to the Brazilian reality, tends in view the importance of the design characterisation and adaptation to the typical roads of Brazil. Copyright © 2000 Society of Automotive Engineers, Inc.

Power losses analysis and cooling system design of three topologies of multilevel inverters

This paper presents the comparison of three topologies of multilevel inverters applied to drive an induction motor of 500 kVA/4.16 kV. The multilevel inverters analyzed are: a neutral point clamped inverter, a symmetrical cascaded multilevel inverter and a hybrid asymmetrical cascaded multilevel inverter. The performance indexes used in the comparison are total harmonic distortion, first order distortion factor, semiconductors power losses distribution and heat-sink volume. The comparison is developed with the purpose of finding the efficiency and the heat-sink volume where the three systems present the same output filter. ©2008 IEEE.

Improvement and evaluation of the MS2SV for mixed systems design described in abstraction high level

This paper presents an important improvement of the MS2SV tool. The MS2SV performs the translation of mixed systems developed in MATLAB / Simulink for a structural or behavioral description in VHDL-AMS. Previously, the MS2SV translated only models of the LIB MS2SV library. This improvement allows designer to create your own library to translation. As case study was used a rudder controller employed in an unmanned aerial vehicle. For comparison with the original model the VHDL-AMS code obtained by the translation was simulated in SystemVision environment. The results proved the efficiency of the tool using the translation improvement proposed in this paper.

Design & prototipagem: conhecimento e uso da prototipagem rápida no design brasileiro

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Vibration Control Applied in a Semi-Active Suspension using Magneto Rheological Damper and Optimal Linear Control Design

In this paper we study the behavior of a semi-active suspension witch external vibrations. The mathematical model is proposed coupled to a magneto rheological (MR) damper. The goal of this work is stabilize of the external vibration that affect the comfort and durability an vehicle, to control these vibrations we propose the combination of two control strategies, the optimal linear control and the magneto rheological (MR) damper. The optimal linear control is a linear feedback control problem for nonlinear systems, under the optimal control theory viewpoint We also developed the optimal linear control design with the scope in to reducing the external vibrating of the nonlinear systems in a stable point. Here, we discuss the conditions that allow us to the linear optimal control for this kind of non-linear system.

Vestir para incorporar: a sedução da idéia no design de moda

This article is a reflection on the clothes used as a ideology vehicle, fashion used by groups, tribes, and available to all those who do not belong to those. Since stylists and designers began to get inspirations "on the street", leaving aside the arrogance and restrictions imposed by the major international trends, it’s visible they have been more open to non-Western cultures and cultures from past and present. This generates consumers seeking for more than clothes: they identify and perform a read of author’s (stylist) interpretations, choosing the "ideas" they will wear.