EFFECT of DIFFERENT SOLID AMOUNTS IN THE PHYSICAL and MICROSCOPICAL PROPERTIES of SiC POROUS CERAMICS

The presence of pores in ceramics is directly related to the chosen forming process. So, in the starch consolidation method, the ceramics show, after burning, pores with morphology similar to that presented by this organic material. on the other hand, the increase in solid load leads up to alterations in dispersion viscosity, increasing the thermal stresses during drying and sintering processes. In order to verify the solid percentage influence in ceramic final properties, samples were prepared with silicon carbide in different compositions using or not starch as binder agent and pore forming element. The characterization of the ceramic pieces was performed by superficial roughness measurements, porosity besides by optical and scanning electron microscopy. The results showed ceramics with SiC and starch presented physical and microscopic properties slightly higher in relation to those with only ceramic powder in their composition. The presence of organic material, agglomerated and foam during the forming were essential for the final properties of the studied samples.

Effects of Compounds from Passiflora edulis Sims f. flavicarpa Juice on Blood Coagulation and on Proteolytic Enzymes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Formation of SiC by radiative association

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Obtenção in situ do compósito alfa-SiAlON-SiC

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development of alpha-SiAlON-SiC ceramic composites by liquid phase sintering

In this work, in situ alpha-SiAlON-SiC ceramic composites were obtained,by, liquid phase sintering, using SiC as reinforcement. Different beta-SiC powder contents (0-20 wt.%), were added to Si3N4-AlN-RE2O3. powder mixtures, and compacted by cold isostatic pressing. The samples were sintered at 1950 degrees C for 1 h, in N-2 atmosphere. Sintered: samples were characterized by relative density, weight loss, X-ray diffraction and scanning electron microscopy. Furthermore, mechanical properties such as hardness and fracture toughness were determined by Vickers indentation method. Lattice parameters of the alpha' phase did not considerably change with increase of SiC content. However, morphology, average grain size and aspect ratio of the alpha' phase were considerably changed with increase of the SiC content. These behavior influences significantly the mechanical properties of this hard ceramic composite. (C) 2006 Elsevier Ltd. All rights reserved.

Stacking faults in SiCf/SiC composite obtained by chemical vapor reaction process

SiC fiber-reinforced SiC matrix composite (SiCf/SiC) is one of the leading candidates in ceramic materials for engineering applications due to its unique combination of properties such as high thermal conductivity, high resistance to corrosion and working conditions. Fiber-reinforced composites are materials which exhibit a significant improvement in properties like ductility in comparison to the monolithic SiC ceramic. The SiCf/SiC composite was obtained from a C/C composite precursor using convertion reaction under high temperature and controlled atmosphere. In this work, SiC phase presented the stacking faults in the structure, being not possible to calculate the unit cell size, symmetry and bond lengths but it seem equal card number 29-1129 of JCPDS.

Coagulation-flocculation of anaerobically treated sugarcane stillage

Anaerobic digestion applied to stillage usually results in treatment performances. However, effluents from anaerobic reactors still present a residual polluting load due to the presence of organic recalcitrant compounds. Additional treatment methods, such as coagulation-flocculation, may be utilized to improve the final effluent quality. In this study, we assessed the processes of coagulation and flocculation for sugarcane stillage samples previously submitted to anaerobic digestion, aiming to obtain optimal conditions for the physicochemical treatment. Natural corn starch and ferric chloride were tested as coagulants. While starch was considered as not suitable for the treatment for the tested conditions, ferric chloride assays presented satisfactory results. The investigated parameters included coagulant solution dose, rapid mixing gradient and time, flocculation gradient and time, and sedimentation time. Their adjusted values at which better performances obtained were, respectively, 1.6 g L-1, 325 rpm, 10 s, 65 rpm, 20 and 20 min. The best color, turbidity, and chemical oxygen demand removal efficiencies were 95, 97, and 65%, respectively. Stillage pH variation to alkaline conditions did not result in improved removal efficiencies. Although relatively high removal efficiencies of constituents were obtained, the final effluent characteristics did not fit regulations of water reuse in the agriculture through fertigation. However, stillage can definitely become more easily managed if better final effluent quality control parameters are achieved, enabling for example effluents discharge in water bodies. © 2013 Copyright Balaban Desalination Publications.

Análise crítica dos critérios diagnósticos da Sociedade Internacional de Cefaléia (SIC - 1988 e SIC - 2003), das cefaléias na infância e na adolescência

Pós-graduação em Bases Gerais da Cirurgia - FMB

Estudo de cerâmicas de SiC e Al2O3 tratadas por expansor de plasma de nitrogênio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

CrataBL, a lectin and Factor Xa inhibitor, plays a role in blood coagulation and impairs thrombus formation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Corrosion prevention for Al2O3/SiC/C/MgAl2O4 based ceramics by means of impregnation with cerium-carrying solution

A cerium-carrying solution was developed so as to aprtially fill the open porosity of Al2O3/SiC/C/MgAl2O4 based refractory lining microstructure used in torpedo ladles, thereby enhancing wear resistance. The protection mchanism was cleared up and introduced from the impregnation technique using a cerium-carrying solution.

Coagulation Factor XII Gene Mutation in Brazilian Families with Hereditary Angioedema with Normal C1 Inhibitor

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Anodization mechanism on SiC nanoparticle reinforced al matrix composites produced by power metallurgy

Specimens of aluminum-based composites reinforced by silicon carbide nanoparticles (Al/SiCnp) produced by powder metallurgy (PM) were anodized under voltage control in tartaric-sulfuric acid (TSA). In this work, the influence of the amount of SiCnp on the film growth during anodizing was investigated. The current density versus time response and the morphology of the porous alumina film formed at the composite surface are compared to those concerning a commercial aluminum alloy (AA1050) anodized under the same conditions. The processing method of the aluminum alloys influences the efficiency of the anodizing process, leading to a lower thicknesses for the unreinforced Al-PM alloy regarding the AA1050. The current density versus time response is strongly dependent on the amount of SiCnp. The current peaks and the steady-state current density recorded at each voltage step increases with the SiCnp volume fraction due to the oxidation of the SiCnp. The formation mechanism of the anodic film on Al/SiCnp composites is different from that occurring in AA1050, partly due the heterogeneous distribution of the reinforcement particles in the metallic matrix, but also to the entrapment of SiCnp in the anodic film.