Determination and statistical treatment of short-circuit currents for faults on the lines of networks of 440 kV CESP system

The distribution of short-circuit current is investigated by means of two methods, one direct and the other analytic; both methods consider uniform probability distribution of line faults. In the direct method, the procedure consists of calculating fault currents at equidistant points along the line, starting from one of the end points and considering the other end open. The magnitude of the current is classified according to Brazilian standards (regulation NBR-7118). The analytic method assumes that the distribution of short-circuit currents through the busbar and the distribution of the line length connected to it are known, as well as the independence of values. The method is designed to determine the probability that fault currents through a line will surpass the pre-established magnitude, thus generating frequency distribution curves of short-circuit currents along the lines.

Unbalanced Three-Phase Induction Motors Starting and Arc Welding Machines Short-Circuit Modeling

Three-Phase Induction Motors (TIM) and Arc Welding Machines (AWM) are loads of special behavior widely used in industrial and commercial installations, and therefore may contribute significantly to the deterioration of the quality of energy supplied by utilities. This paper proposes a modeling in constant power of the unbalanced TIM starting using Genetic Algorithm (GA) and AWM short-circuit based on their statics characteristics curves. The proposed models are compared with the conventional models in the literature. The results showed the good performance of the proposed models, allowing a more precise analysis of the real requests of these loads.

Electric power systems transient stability analysis by neural networks

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Dynamic behavior of a linear induction motor

Although conventional rotating machines have been largely used to drive underground transportation systems, linear induction motors are also being considered for future applications owing to their indisputable advantages. A mathematical model for the transient behavior analysis of linear induction motors, when operating with constant r.m.s. currents, is presented in this paper. Operating conditions, like phase short-circuit and input frequency variations and also some design characteristics, such as air-gap and secondary resistivity variations, can be considered by means of this modeling. The basis of the mathematical modeling is presented. Experimental results obtained in the laboratory are compared with the corresponding simulations and discussed in this paper.

Evaluation of a multiobjective performance index for distribution systems with distributed generation

Here a multiobjective performance index for distribution systems with distributed generation based on a steady-state analysis of the network is proposed. This index quantifies the distributed generation impact on total losses, voltage profile and short circuit currents, and will be used as objective function in an evolutionary algorithm aimed at searching the best points for connecting distributed generators. Moreover, a loss allocation technique, based on the Zbus method, is applied on the original configuration of the network to obtain a good quality initial population. An IEEE medium voltage distribution network is analysed and results are presented and discussed.

A mixed-integer linear programming approach for optimal type, size and allocation of distributed generation in radial distribution systems

This paper presents a mixed-integer linear programming approach to solving the problem of optimal type, size and allocation of distributed generators (DGs) in radial distribution systems. In the proposed formulation, (a) the steady-state operation of the radial distribution system, considering different load levels, is modeled through linear expressions; (b) different types of DGs are represented by their capability curves; (c) the short-circuit current capacity of the circuits is modeled through linear expressions; and (d) different topologies of the radial distribution system are considered. The objective function minimizes the annualized investment and operation costs. The use of a mixed-integer linear formulation guarantees convergence to optimality using existing optimization software. The results of one test system are presented in order to show the accuracy as well as the efficiency of the proposed solution technique.© 2012 Elsevier B.V. All rights reserved.

Análises e estudos para alocação e ajustes de dispositivos de proteção em redes de média tensão de energia elétrica com geração distribuída

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comparação entre métodos e análise de correntes de curto-circuito

Overcurrents may endanger the whole electrical system and living beings, they are the result of short circuits and failures that can occur in electrical systems, no matter how well designed they are. Therefore it is important to predict these failures with analysis of electrical systems to make it possible to design appropriate protections, to ensure that those intervene properly and avoid technical and mainly human losses. However there is no standard for calculation of the short circuit currents, the main authors of the national literature about the subject suggest various methods, knowing the particularities among them provides quick and easy choice and proper application of them. To do so, a base case from an electrical system that presents a short circuit is chosen, which will be analyzed using the methods presented

Identification of transmission line parameters from temporal measurements of currents and voltages in their terminals: Influence oh the length line

The objective of this paper is to show a methodology to estimate transmission line parameters. The method is applied in a single-phase transmission line using the method of least squares. In this method the longitudinal and transversal parameters of the line are obtained as a function of a set of measurements of currents and voltages (as well as their derivatives with respect to time) at the terminals of the line during the occurrence of a short-circuit phase-ground near the load. The method is based on the assumption that a transmission line can be represented by a single circuit π. The results show that the precision of the method depends on the length of the line, where it has a better performance for short lines and medium length. © 2012 IEEE.

Fault analysis in four-wire distribution networks

The neutral wire in most existing power flow and fault analysis software is usually merged into phase wires using Kron's reduction method. In some applications, such as fault analysis, fault location, power quality studies, safety analysis, loss analysis etc., knowledge of the neutral wire and ground currents and voltages could be of particular interest. A general short-circuit analysis algorithm for three-phase four-wire distribution networks, based on the hybrid compensation method, is presented. In this novel use of the technique, the neutral wire and assumed ground conductor are explicitly represented. A generalised fault analysis method is applied to the distribution network for conditions with and without embedded generation. Results obtained from several case studies on medium- and low-voltage test networks with unbalanced loads, for isolated and multi-grounded neutral scenarios, are presented and discussed. Simulation results show the effects of neutrals and system grounding on the operation of the distribution feeders.

Investigating effects of neutral wire and grounding in distribution systems with faults

In some applications like fault analysis, fault location, power quality studies, safety analysis, loss analysis, etc., knowing the neutral wire and ground currents and voltages could be of particular interest. In order to investigate effects of neutrals and system grounding on the operation of the distribution feeders with faults, in this research a hybrid short circuit algorithm is generalized. In this novel use of the technique, the neutral wire and assumed ground conductor are explicitly represented. Results obtained from several case studies using IEEE 34-node test network are presented and discussed.

Um método para detecção e classificação de curtos-circuitos em redes de distribuição de energia elétrica baseado na transformada de Fourier e em redes neurais artificiais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Detecção e classificação de faltas de alta impedância em sistemas elétricos de potência usando lógica Fuzzy

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Contribuições para o estudo de atribuição de responsabilidades em circuitos elétricos de baixa tensão

Pós-graduação em Engenharia Elétrica - FEB

Desenvolvimento de um sistema de proteção e metodologia para localização de faltas em sistemas de distribuição

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)