Photoelastic comparison of single tooth implant-abutment-bone of platform switching vs conventional implant designs

Objectives: The maintenance and stability of peri-implantar soft tissue seem to be related to the crestal bone around the implant platform and different implant designs connections might affect this phenomenon. The aim of this study was to evaluate by photoelastic analysis the stress distribution in the cervical and apical site of implant-abutment interface of conventional implant joints (external hex, internal hex and cone morse) and compare to the novel platform switching design. Materials and methods: It was fabricated photoelastic models using five different implant-abutment connection, one set of external hex (Alvim Ti, Neodent, Curitiba, Brazil), one set of internal hex (Full Osseotite, Biomet 3i, Florida, USA), one cone morse set (Alvim CM, Neodent, Curitiba, Brazil), and two sets of internal hex plus platform switching concept (Alvim II Plus, Neodent, Curitiba, Brazil) (Certain Prevail, Biomet 3i, Florida, USA). These models were submitted to two compressive loads, axial from 20 kgf (load I) and another (load II), inclined 45° from 10 kgf. During the qualitative analysis, digital pictures were taken from a polariscope, for each load situation. For the quantitative analyses in both situations of load, the medium, minimum and maximum in MPa values of shear strain were determined in the cervical and apical site. The Kruskal-Wallis test was used to compare the results between the different systems and between cervical and apical site were compared using Mann-Whitney U test. Results: The results from qualitative analysis showed less concentration of strain in the cervical area to the internal hex plus platform switching (Certain Prevail), in both situation of load. The same results were get in the quantitative analysis, showing less stress concentrations around the implant Certain Prevail with internal hex plus the novel design (17.9 MPa to load I and 29.5 MPa to load II), however, without statistical significant difference between the systems. Conclusion: The minor stress concentration strongly suggest the use of platform switching design as a manner to prevent bone loss around the implant-abutment platform. Clinical Significance: From the result of this study its possible to make clinical decision for implant system which provides implant components with platform switching characteristics.

Resistência mecânica de juntas coladas em madeira de Eucalyptus sp

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Transpressional tectonics and strain partitioning during oblique collision between three plates in the Precambrian of southeast Brazil

This paper is part of the special publication Continental transpressional and transtensional tectonics (eds R.E. Holdsworth, R.A. Strachan and J.F. Dewey). Two orogenic belts have been recognized in south- east Brazil, which are interpreted to have been formed as a product of diachronous collisions between three continental plates. Wide crustal-scale shear belts have developed both between and inboard of the collided and amalgamated plate borders. These shear belts record frontal, oblique or lateral displacements during oblique plate convergence and A-type subduction. The overall structural style of each belt depends on the angle subtended between the plate boundary and the convergence vector. The E-W branch between the Sao Paulo and Brasilia plates the Campo do Meio strike-slip shear belt, has undergone dominantly sinistral wrench dominated transpression along a set of folds and shear zones dipping southwards. The NE-SW branch between the Sao Paulo and Vitoria plates, the Paraiba do Sul strike-slip shear belt, has undergone a partitioned dextral transpression, whereas the north-south branch between the Brasilia and Vitoria plates is essentially a frontal thrust system with only a weak component of dextral strike-slip. These complex structural patterns, formed at deep to mid-crustal levels, reflect temporal and spatial partitioning at all scales between flattening and non- coaxial deformation, and down-dip and strike-slip shearing, in tangential as well as in transcurrent structural domains. Additionally, this area demonstrates that regional flower structures, lateral extrusion and other secondary deformations across the yz sections of transpressional belts are important in accommodating shortening in obliquely convergent orogens.

Theoretical approach including friction for determining strain limits in punch stretching of anisotropic sheet metals

A new analytical theory including friction was developed to assess strain limits in punch stretching of anisotropic sheet metals. This new approach takes into consideration the anisotropic behaviour of sheet materials and could explain the mechanical behaviour of a variety of anisotropic sheet materials. The theory explains the sheet metal failure so for the drawing as the stretching region of the forming limit curve, particularly for materials that present the strain-ratio dependence of limit strain ε 1, where dε 1/dρ is not always greater than zero. dε 1/ dρ or dε 1/dε 2 could be equal to or smaller than zero for a range of materials. Therefore, this new theory can explains such experimental observations, besides to assuming that membrane element relations near the pole, for the case of punch stretching are dependent of sheet metal properties as the process history and also suggests that the onset of local necking is controlled by shear. Thus, theoretical results obtained through this new approach are compared with experimental results available in the literature. It is demonstrated the effect of friction on a FLC curve for both regions, drawing and stretching. © 2010 American Institute of Physics.