Stepping-motor-driven constant-shear-rate rotating viscometer

Despite the frequent use of stepping motors in robotics, automation, and a variety of precision instruments, they can hardly be found in rotational viscometers. This paper proposes the use of a stepping motor to drive a conventional constant-shear-rate laboratory rotational viscometer to avoid the use of velocity sensor and gearbox and, thus, simplify the instrument design. To investigate this driving technique, a commercial rotating viscometer has been adapted to be driven by a bipolar stepping motor, which is controlled via a personal computer. Special circuitry has been added to microstep the stepping motor at selectable step sizes and to condition the torque signal. Tests have been carried out using the prototype to produce flow curves for two standard Newtonian fluids (920 and 12 560 mPa (.) s, both at 25 degrees C). The flow curves have been obtained by employing several distinct microstep sizes within the shear rate range of 50-500 s(-1). The results indicate the feasibility of the proposed driving technique.

Viscosity measurement of Newtonian liquids using the complex reflection coefficient

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo do comportamento reológico de barbotinas preparadas com argilas da Formação Corumbataí utilizadas no pólo cerâmico de Santa Gertrudes (SP)

Este estudo surgiu da necessidade das indústrias cerâmicas do pólo de Santa Gertrudes (SP) se adaptarem às mudanças do comportamento do mercado e às exigências dos órgãos ambientais em relação aos riscos causados pela geração de poeira na fase de preparação da massa. Assim, o processo de preparação de massa via úmida pode ser uma alternativa para esta substituição, sendo necessária a obtenção de uma barbotina que apresente um comportamento reológico adequado ao processo e ao consumo de energia. Foram feitas medidas de viscosidade, tensão de cisalhamento e taxa de cisalhamento com viscosímetro rotacional, tendo como parâmetros de controle, o teor de sólidos da barbotina e a granulometria. Desta forma, foram verificadas variações das suspensões, como o comportamento pseudoplástico e a tixotropia. Também foi analisada a dependência do comportamento reológico com a mineralogia das argilas, obtida por difração de raios X. Os resultados das curvas reológicas mostraram-se muito coerentes com a mineralogia determinada, indicando uma piora do comportamento reológico no sentido da base para o topo da Formação Corumbataí, devido à alteração supérgena e presença de esmectitas.

P3L-3 Viscosity measurement of Newtonian liquids using the complex reflection coefficient

This work presents the implementation of the ultrasonic shear reflectance method for viscosity measurement of Newtonian liquids using wave mode conversion from longitudinal to shear waves and vice-versa. The method is based on measuring the complex reflection coefficient (magnitude and phase) at a solid-liquid interface. Viscosity measurements were made in the range from 1 to 3.5MHz at 22.5°C for automotive oil (SAE40) and at 15°C for olive oil. Moreover, measurements of the olive oil were also conducted in the range from 15 to 30°C at 3.5MHz. The experimental results agree with those provided by a rotational viscometer. © 2006 IEEE.

A Simple maxwell Based Model in Order to Represent the frequency-dependent viscosity measured by ultrasound

A previous work showed that viscosity values measured high frequency by ultrasound agreed with the values at low frequency by the rotational viscometer when conditions are met, such as relatively low frequency viscosity. However, these conditions strongly reduce the range of the measurement cell. In order to obtain a measurement range and sensitivity high frequency must used, but it causes a frequency-dependent decrease on the viscosity values. This work introduces a new simple in order to represent this frequency-dependent behavior.model is based on the Maxwell model for viscoelastic , but using a variable parameter. This parameter has physical meaning because it represents the linear behavior the apparent elasticity measured along with the viscosity by .Automotive oils SAE 90 and SAE 250 at 22.5±0.5oC viscosities at low frequency of 0.6 and 6.7 Pa.s, respectively,tested in the range of 1-5 MHz. The model was used in to fit the obtained data using an algorithm of non-linear in Matlab. By including the viscosity at low frequency an unknown fitting parameter, it is possible to extrapolate its . Relative deviations between the values measured by the and extrapolated using the model for the SAE 90 and SAE 250 oils were 5.0% and 15.7%, respectively.©2008 IEEE.

Estudo do comportamento reológico de suspensões argilosas da Formação Corumbataí

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Misturador para análise de propriedades reológicas

This study aimed to evaluate the use of a mixer to determine the rheological properties of fluids. The mixer is comprised of an agitation tank and an anchor type impeller. The tests were performed with honey and fruit juices (orange, guava and peach). The rheological characterization was performed using data from the torque and rotation speed required for the operation of fluid agitation. Tests were also made with a concentric cylinder rotational viscometer with the samples being subjected to various shear rates. The rheological parameters were obtained from the flow curves fitted to the power law model. Analyses of results showed that the mixer can be used, within its limitations, to determine rheological properties.

Root system of Panicum maximum Jacq. cv. IPR-86 Mil(e)over-capnio fertilized with nitrogen and submitted to rotational stocking

The effect of nitrogen on the root system of the species Panicum maximum Jacq. cv. IPR-86 Mil (e) over cap nio, under grazing, was evaluated. The N rates were 0; 150; 300 and 450 kg/ha. year. The root density was evaluated during pregrazing at five years of successive N application, in three depths (0-10; 10-20 and 20-40 cm) and the root growth at 7, 14, 21, and 35 days after grazing. The grazing method adopted was rotational stocking. Root length and root mass densities in pre-and post-grazing presented maximum values at rates 204, 206, 192, and 197 kg/ha of N, respectively. The root growth (in root length density) increased, on average, until 29 days after grazing at rates 0, 150, and 300 kg/ha; at 450 kg/ha N rate, the increase was linear. Independently of N rates, around 60 and 25% of IPR-86 Mil (e) over cap nio cultivar root system was concentrated in 0-10 and 10-20 cm depth, respectively.

g-acceleration of gravity: its measurement from the shape of water by using a computerized rotational system

This paper proposes a different experimental setup compared with the traditional ones, in order to determine the acceleration of gravity, which is carried out by using a fluid at a constant rotation. A computerized rotational system-by using a data acquisition system with specific software, a power amplifier and a rotary motion sensor-is employed in order to evaluate the angular velocity and g. An equation to determine g is inferred from fluid mechanics. For this purpose, the fluid's parabolic shape inside a cylindrical receptacle is considered using a rotational movement.

Analytical and semi-analytical analysis of an artificial satellite's rotational motion

The rotational motion of an artificial satellite is studied by considering torques produced by gravity gradient and direct solar radiation pressure. A satellite of circular cylinder shape is considered here, and Andoyers variables are used to describe the rotational motion. Expressions for direct solar radiation torque are derived. When the earth's shadow is not considered, an analytical solution is obtained using Lagrange's method of variation of parameters. A semi-analytical procedure is proposed to predict the satellite's attitude under the influence of the earth's shadow. The analytical solution shows that angular variables are linear and periodic functions of time while their conjugates suffer only periodic variations. When compared, numerical and analytical solutions have a good agreement during the time range considered.

Study of Stability of Rotational Motion of Spacecraft with Canonical Variables

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Implant-retained thumb prosthesis with anti-rotational attachment for a geriatric patient

This report presents the use of a dental implant with an anti-rotational attachment for the retention of a thumb prosthesis. A retention system was manufactured with an attachment (UCLA) screwed into the implant with a two-bar system that was cast in metallic silver palladium. A substructure made from heat-cured acrylic resin was joined to the retention system by clips to join the thumb to the finger (bar clip) in the cast with implant rejoinder. The silicone material, Silastic-MDX 44210, was used to achieve function and aesthetics. Following osseointegration, no skin problems were observed. Whilst the implant-retained digital prosthesis presented some motor limitations, it allowed the patient to return to entertainment and achieve social conviviality.

A Model Coupling Vibrational and Rotational Motion for the DNA Molecule

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Vibrational-rotational analysis of the Hulthen potential using hydrogenic eigenfunction bases

Hulthen's potential admits analytical solutions for its energy eigenvalues and eigenfunctions corresponding to zero orbital angular momentum stales, but its non zero angular momentum states are not equally known. This work presents a vibrational-rotational analy sis of Hulthen's potential using hydrogenic eigenfunction bases, which may be of interest and useful to students of quantum mechanics at different stages.

A comparative study of the low energy HD plus o-/p-H-2 rotational excitation/de-excitation collisions and elastic scattering

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)