Rod length influence in torque measurement of SPT-T test

Since Ranzini suggested supplementing the SPT test with measurement of the torque required to turn the split spoon sampler after driving, many Brazilian engineers have been using this in the design of pile foundations. This paper presents a study of the rod length influence in the torque measurement. A theoretical study of material resistance considering torsion and bending in a thin wall tubular steel shaft was performed. It makes possible to conclude that the shearing tension caused by the proper weight represents less than 1% of the shearing tension caused by the turning moment. In addition, an experimental study was done with electric torquemeters fixed in a horizontal rod system. The tests were being carried out to analyze rods of one meter to twenty meters in length and the measurements were collected at the ends of each rod length verifying the efficiency data. As a result, it is possible to verify that the torque difference through rod length is lower than minimum scales of mechanical torquemeters that are used on practical engineering. Also a fact to be considered is a big torque loss for values under 20 N.m of applied torque. This way, the SPT-T is not adequate to low consistency soil. Copyright ASCE 2007.

The fractional and nonlinear magneto-flexible rod

This paper deals with a system involving a flexible rod subjected to magnetic forces that can bend it while simultaneously subjected to external excitations produces complex and nonlinear dynamic behavior, which may present different types of solutions for its different movement-related responses. This fact motivated us to analyze such a mechanical system based on modeling and numerical simulation involving both, integer order calculus (IOC) and fractional order calculus (FOC) approaches. The time responses, pseudo phase portraits and Fourier spectra have been presented. The results obtained can be used as a source for conduct experiments in order to obtain more realistic and more accurate results about fractional-order models when compared to the integer-order models. © Published under licence by IOP Publishing Ltd.

A América Latina, de Manoel Bomfim, e Ariel, de José Enrique Rodó: ensaios de interpretação latino-americana

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A nação escrita entre a prática e o ideal: os projetos de Monteiro Lobato e de José Enrique Rodó

Pós-graduação em Ciências Sociais - FFC

Ideologia e política em José Enrique Rodó: liberalismo e jacobinismo no Uruguai (1895-1917)

Pós-graduação em História - FCHS

Análise estrutural de Tie-Rod pelo método dos elementos finitos e através de cálculos analíticos

Currently one of the great concerns of the aeronautical industry is in relation to the security and integrity of the aircraft and its equipments / components when under critical flight maneuvers such as during landing / takeoff and emergency maneuvers. The engineers, technicians and scientists are constantly developing new techniques and theories to reduce the design time and testing, ir order to minimize costs. More and more the Finite Element Method is used in the structural analysis of a project as well as theories based on experimental results. This work aimed to estimate the critical load to failure for tensile, compression and buckling of the Tie-Rod, a fixture aircraft widely used on commercial aircrafts. The analysis was performed by finite element method with the assistance of software and by analytical calculations. The results showed that the Finite Element Method provides relative accuracy and convenience in the calculations, indicating critical load values slightly lower than those found analytically for tension and compression. For buckling, the Finite Element Method indicates a critical load very similar to that found analytically following empirical theories, while Euler's theory results in a slightly higher value. The highest risk is to fail by buckling, but the geometric irregularity of Tie-Rod pieces makes difficult the calculations, therefore a practical test must be done before validation of the results

Metacromasia para identificação de basófilos sanguíneos em surubim híbrido: contribuição metodológica

Padua S.B. & Ishikawa M.M. [Metachromasia for blood basophils identification in hybrid surubim catfish: methodological contribution]. Metacromasia para identificacao de basofilos sanguineos em surubim hibrido: contribuicao metodologica. Revista Brasileira de Medicina Veterinaria, 33(3):147-150, 2011. Centro de Aquicultura da Unesp/Jaboticabal Rod. Paulo Donato Castellane, s/n Bairro Rural, Jaboticabal, 14884-900, SP. Brasil. E-mail: santiagopadua@live.comDifferent protocols of fixation and hydrolysis of blood smears of hybrid surubim catfish for metachromasia to marking blood basophils were evaluated. For this reason, methanol, acid-alcohol and formalin vapor were tested as fixatives. For hydrolysis of blood smears, HCl, citric acid and 2-Mercaptoethanol + Urea + NaCl solutions was evaluated. After procedures, the blood smears was stained with toluidine blue (0.025%) diluted in McIlvaine buffer (pH 4). The different protocols for fixation and hydrolysis of blood smears for metachromasia influenced the quality of the reaction. Hydrolysis with 2-Mercaptoethanol + Urea + NaCl solutions provided negative results when using methanol and acid-alcohol as fixatives. The fixation with acid-alcohol associated with citric acid hydrolysis provides highest quality reason.

Ocorrência de Megabacteriose em Periquitos Autralianos, Canários e Agapornis na Região de Ribeirão Preto- Estado de São Paulo - Brasil

Este trabalho tem como objetivo relatar a ocorrência de um agente etiológico, denominado na Europa, Australia e EUA como megabactéria, observado em estômago de pequenas aves (canários belgas, agapornis e periquitos australianos), provenientes da região de Ribeirão Preto, Estado de São Paulo/SP. As necropsias de 64 aves silvestres (4 periquitos australianos, 12 agapornis e 48 canários), realizadas no perído de 1994 a 1997, foram analisadas, constatando-se em 56% dos casos a presença de estruturas filiformes, acidofílicas sob coloração Giemsa, gram positivas, existentes no muco do proventrículo, descritas na literatura como megabactérias. Foram testados diversos tipos de meios de cultura para reprodução in vitro deste microrganismo. Foram ainda comparadas as dimensões (comprimento e largura) dessa bactéria obtida apartir do esfregaço fresco de muco proventricular e da megabactéria proveniente de cultivo in vitro. Também foram listados os principais achados macroscópicos do animais portadores desta bactéria.

Análise tridimensional de esforços em elementos rompedores de semeadoras de plantio direto

As informações da avaliação de mecanismos de abertura de sulco de semeadoras de plantio direto auxiliam as empresas no dimensionamento de ferramentas rompedoras do solo, que buscam menor requerimento energético. Este trabalho foi realizado num solo classificado como Latossolo Vermelho com o objetivo de avaliar tridimensionalmente os esforços dos mecanismos de abertura de sulco de semeadoras adubadoras de plantio direto. O delineamento experimental utilizado foi o de blocos ao acaso com cinco tratamentos, sendo cinco mecanismos de abertura de sulco (disco liso - DL, disco corrugado - DC, disco ondulado - DO, disco duplo - DD e haste sulcadora - H). Para mensurar os esforços dos mecanismos de abertura de sulco, foi utilizado um dinamômetro com sensibilidade nas direções horizontal, transversal e vertical e no momento fletor e torsor. A avaliação mostrou que a interação entre mecanismos de abertura de sulco e carga vertical não foi significativa, entretanto os fatores foram significativos quando analisados individualmente. O resultado individual dos mecanismos de abertura de sulco mostrou que o disco ondulado proporcionou maior área de mobilização do solo, a haste sulcadora apresentou o menor valor de força vertical e o disco duplo e a haste sulcadora obtiveram o menor esforço horizontal.

Esforços em ferramentas rompedoras de solo de semeadoras de plantio direto

The individual evaluation of mechanisms for opening furrows to drop the seeds in a no-tillage seeders cultivation assists the companies in the sizing of opening tools of the ground, that search for minor energy petition and for diminishing the ground area mobilized. Therefore this work had the aim of evaluate the efforts of five different mechanisms of opening of ridge of seeding of direct plantation varyng the vertical load. The experiment was installed in one ground classified as Dystroferric Red Nitosol. The used experimental delineation was of the one randomized blocks in a factorial project 5 x 4, constituted a the following factors: five mechanisms of furrow opening (even disk - DL, corrugated disk - DC, ondulated disk - DO, double disk - DD and furrow rod - F) and four vertical loads (750, 1500, 2250 and 3000 N). To measure the forces in the studied treatments a dynamometer with sensitivity in the directions was used horizontal, lateral and vertical direction. The evaluation showed that the interaction between mechanisms of opening of ridge and vertical load was not significant, however the factors were significant when analyzed individually. The connecting rod promoted mobilization of the ground with smaller draft of horizontal effort reaching depths of work. The work showed that the vertical load influenced the depth of work of the mechanisms of ridge opening. The mechanisms of ridge opening of record type need vertical force to penetrate into the ground.

Biomass and Stand Characteristics of a Highly Productive Mixed Douglas-Fir and Western Hemlock Plantation in Coastal Washington

Aboveground biomass predictive equations were developed for a highly productive 47-year-old mixed Douglas-fir and western hemlock stand in southwest Washington State to characterize the preharvest stand attributes for the Fall River Long-Term Site Productivity Study. The equations were developed using detailed biomass data taken from 31 Douglas-fir and 11 western hemlock trees within the original stand. The stand had an average of 615 live trees per hectare, with an average dbh of 35.6 cm (39.1 cm for Douglas-fir and 33.3 cm for western hemlock) and an average total tree height of 31.6 m (32.8 m for Douglas-fir and 30.2 m for western hemlock). Equations developed were of the form In Y = b(1) + b(2) In dbh, where Y = biomass in kg, dbh = diameter in cm at 1.3 m height, b(1) = intercept, and b(2) = slope of equation. Each tree part was estimated separately and also combined into total aboveground biomass. The total aboveground biomass estimation equations were In Y = -0.9950 + 2.0765 In dbh for Douglas-fir, and In Y = -1.6612 + 2.2321 In dbh for western hemlock. The estimate of the aboveground live-free biomass was of 395 Mg ha(-1) (235 Mg ha(-1) for Douglas-fir and 160 Mg ha(-1) for western hemlock), with 9.5, 29.3, 12.9, 308, and 32.7 Mg ha(-1) in the foliage, live branches, dead branches, stem wood, and stem hark, respectively. When compared with biomass estimates from six other studies, ranging in age from 22 to 110 years and from 96.3 to 636 Mg ha(-1), the biomass of the Fall River site was relatively high for its age, indicating very high productivity.

Viscosity measurement of Newtonian liquids using the complex reflection coefficient

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação histológica da regeneração óssea do rádio e ulna em cães submetidos ao alongamento com o fixador de Ilizarov

O objetivo do estudo foi analisar histologicamente a qualidade, tipo e orientação dos tecidos formados na área de regeneração óssea produzida durante alongamento simultâneo do rádio e da ulna, com fixador externo de Ilizarov, a partir de osteotomia subperiosteal diafisária distal, com dois incrementos diários de 0,5 mm. A montagem foi composta de dois anéis e quatro hastes telescópicas, sendo a distração óssea iniciada no sexto dia de pós-operatório. Utilizaram-se 15 cães, sem raça definida, adultos, com peso corpóreo entre 17 e 30 kg, divididos por sorteio em subgrupos (A, B, C, D e E) compostos por três animais, que foram submetidos a eutanásia após os seguintes procedimentos: A- oito dias de alongamento, B- 15 dias de alongamento, C- 22 dias de alongamento, D- 28 dias de alongamento e oito dias de fase neutra com o fixador, E- 28 dias de alongamento, 60 dias de fase neutra com fixador e 45 dias sem fixador. Os resultados obtidos mostram que o tipo e localização da osteotomia, bem como o ritmo de distração utilizado, não interferiram sobremaneira na regeneração óssea. A reparação óssea foi eficiente, notadamente intramembranosa, contudo nos subgrupos B e C foi observada a presença de cartilagem.

Myonecrosis by Clostridium septicum in a dog, diagnosed by a new multiplex-PCR

Clostridial myositis is an acute, generally fatal toxemia that is considered to be rare in pet animals. The present report describes an unusual canine clostridial myositis that was diagnosed by a new multiplex-PCR (mPCR) designed for simultaneous identification of Clostridium sordellii, Clostridium septicum, Clostridium perfringens type A, Clostridium chauvoei, and Clostridium novyi type A. A ten-month-old male Rottweiler dog, that had displayed lameness and swelling of the left limb for 12 h, was admitted to a veterinary hospital. The animal was weak, dyspneic and hyperthermic, and a clinical examination indicated the presence of gas and edema in the limb. Despite emergency treatment, the animal died in only a few minutes. Samples of muscular tissue from the necrotic area were aseptically collected and plated onto defibrinated sheep blood agar (5%) in anaerobic conditions. Colonies suggestive of Clostridium spp. were submitted to testing by multiplex-PCR. Impression smears of the tissues, visualized with Gram and also with panoptic stains, revealed long rod-shaped organisms, and specimens also tested positive using the fluorescent antibody technique (FAT). The FAT and mPCR tests enabled a diagnosis of C. septicum myonecrosis in the dog. (C) 2012 Elsevier Ltd. All rights reserved.

Histological and three-dimensional evaluation of osseointegration to nanostructured calcium phosphate-coated implants

Nanostructures on implant surfaces have been shown to enhance osseointegration; however, commonly used evaluation techniques are probably not sufficiently sensitive to fully determine the effects of this process. This study aimed to observe the osseointegration properties of nanostructured calcium phosphate (CaP)-coated implants, by using a combination of three-dimensional imaging and conventional histology. Titanium implants were coated with stable CaP nanoparticles using an immersion technique followed by heat treatment. Uncoated implants were used as the control. After topographical and chemical characterizations, implants were inserted into the rabbit femur. After 2 and 4 weeks, the samples were retrieved for micro-computed tomography and histomorphometric evaluation. Scanning electron microscopy evaluation indicated that the implant surface was modified at the nanoscale by CaP to obtain surface textured with rod-shaped structures. Relative to the control, the bone-to-implant contact for the CaP-coated implant was significantly higher at 4 weeks after the implant surgery. Further, corresponding 3-D images showed active bone formation surrounding the implant. 3-D quantification and 2-D histology demonstrated statistical correlation; moreover, 3-D quantification indicated a statistical decrease in bone density in the non-coated control implant group between 2 and 4 weeks after the surgery. The application of 3-D evaluation further clarified the temporal characteristics and biological reaction of implants in bone. (C) 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.