Consumo de combustível na operação de subsolagem realizada antes e depois de diferentes sistemas de preparo periódico do solo

A subsolagem tem aumentado nos últimos anos de forma indiscriminada, faltando estudos que norteiem os melhores procedimentos para que novos problemas não sejam acrescentados devido a subsolagens inadequadas ou mesmo em solos onde a operação é desnecessária, e principalmente buscar redução no consumo de combustível. Dessa forma, este trabalho teve o objetivo de avaliar o consumo de combustível na operação de subsolagem efetuada antes e depois de diferentes sistemas de preparo periódico do solo, classificado como Nitossolo Vermelho distroférrico. Os preparos foram realizados com arado de discos, arado de discos mais uma gradagem de nivelamento, grade pesada, grade pesada mais gradagem de nivelamento e escarificador. A realização da subsolagem depois dos sistemas de preparo periódico requereu 15% menos de potência na barra de tração. A subsolagem depois dos diferentes sistemas de preparo economizou 16,5% de combustível por área. O deslizamento das rodas motrizes e a velocidade média operacional obtiveram melhor desempenho quando se realizou a subsolagem depois do preparo do solo.

Análise de ordem de uma bancada experimental aplicada ao estudo de rotores

In this work the main concepts to apply to dynamic signal analysis technique for rotating machines known as order analysis, discussing their characteristics and applying it on an experimental test rig. It aims to characterize the dynamic behavior of experimental test rig in run up and run down tests, it's operational speed range and the identification of the critical speed of shaft rotation. The results of the critical speed and stationary natural frequency of the shaft are discussed

Operational parameters of soybean seeding in santa fe system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desempenho operacional de um protótipo “aerossolo”

It is been a great deal of interest the studying of the operational performance of tractors and its machinery especially in work conditions. The present study had as objective to evaluate the operational performance of an Aerossolo prototype tracked with a Valtra BM100 4x2 TDA, with the engine power of 73.6 kW (100 cv). The prototype equipment is a drag type, hydraulically commanded, with telescopic heading for longitudinal adjustment, two lateral sections with 28 knifes in each one of them, concrete ballasts, wheels of transport and aggregate breaker coil. The work was conducted in the Department of Agricultural Engineering of the UNESP, Jaboticabal Campus, in a randomized blocks design, factorial 3 x 3, with four repetitions. The nine studied treatments were a combination for three ballast conditions (0; 960 and 1,307 kg) and three angles of the sections (0 degrees; 7 degrees and 14 degrees). The results indicate an increase in operational consumption (liters per hectare) of 32.4% in relation to the concrete ballast addition, and a 26.8% in relation to the angle variation between sections. The working depth, traction force and power demands were higher with the increases in the concrete ballast and the angle variation between sections.

Perdas de grãos e distribuição de palha na colheita mecanizada de soja

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Demanda energética e eficiência da distribuição de sementes de milho sob variação de velocidade e condição de solo

O trabalho teve o objetivo de avaliar a demanda energética e a eficiência da distribuição de sementes de uma semeadora-adubadora para semeadura direta, submetida à variação de velocidade e condições de solo, na semeadura da cultura do milho. O estudo foi desenvolvido em um Nitossolo Vermelho distrófico, na Fazenda Experimental Lageado, no município de Botucatu - SP. O delineamento experimental foi em blocos casualizados, com oito repetições, combinando-se três velocidades de deslocamento (4,4; 6,1 e 8,1 km h-1) e duas condições de solo (solo manejado sob sistema de plantio direto há cinco anos e solo preparado com escarificador há 18 meses). Avaliaram-se a força de tração, a potência na barra de tração, o consumo de combustível, a capacidade de campo efetiva, a distribuição longitudinal de plantas, o coeficiente de variação, o índice de precisão e o número de plantas por hectare (estande inicial). Os resultados revelaram que, aumentando-se a velocidade de 4,4 para 8,1 km h-1, consegue-se aumentar em 86% a capacidade operacional, com incremento de 96% na demanda de potência na barra de tração e redução de 26% no consumo operacional de combustível. A maior velocidade (8,1 km h-1) proporcionou menor porcentual de espaçamentos normais e aumento no porcentual de espaçamentos múltiplos e falhos, maior coeficiente de variação e pior índice de precisão. A variação da velocidade não interferiu no número de plantas por hectare.

Desempenho de uma semeadora-adubadora direta, em função da velocidade de eslocamento e do tipo de manejo da biomassa da cultura de cobertura do solo

O objetivo do presente trabalho foi estudar o desempenho de uma semeadora-adubadora, operando em duas velocidades sobre a palhada da cultura do milheto (Pennisetum glaucum (L.) R. Brown), após diferentes manejos, na semeadura direta da cultura da soja (Glycine Max L.). O experimento foi realizado com seis tratamentos, em esquema fatorial, delineados em blocos ao acaso, com quatro repetições. Os tratamentos combinaram três manejos (triturador de palhas tratorizado, rolo- faca e herbicida) com duas velocidades de deslocamento da semeadora-adubadora (5,2 e 7,3 km h-1). Foram analisadas as seguintes variáveis: acúmulo e decomposição de massa seca do milheto, índice de emergência da cultura da soja, uniformidade de distribuição longitudinal de sementes, capacidade de campo efetiva da semeadora-adubadora e produtividade da soja. Os resultados mostraram que não houve diferença na decomposição da massa de milheto após os manejos e que esses, juntamente com a velocidade de deslocamento do conjunto trator-semeadora-adubadora, não influenciaram no número de dias para a emergência das plântulas de soja e na distribuição longitudinal das sementes. A capacidade de campo efetiva da semeadora-adubadora foi maior na velocidade mais alta. O rendimento de grãos não diferiu significativamente nos tratamentos estudados.

Genetic associations between flight speed and growth traits in Nellore cattle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização física do solo e desempenho operacional de máquinas agrícolas na implantação da cultura do sorgo forrageiro

Forage sorghum can be grown in areas presenting dry and hot environmental situations where the yield of other grasses can often be uneconomical. The objective of this study was to analyze the operating performance of agricultural machines in the deployment of sorghum forage in four tillage systems, as follows: no-tillage system, disk harrow + seeding, disk harrow + two light disking + seeding, minimum tillage + seeding and four seeding different speeds, as follows: 3, 5, 6 and 9 km h(-1). The study was performed under field conditions in FCA/UNESP, Botucatu County, SP, Brazil. The data were subjected to variance analysis in a simple factorial 4 x 4, and a random block design with split plots. Operational performance of the agricultural machinery, physical characteristics the soil, its water content and the yield of dry matter and green sorghum were determined. The operational performance of agricultural machines in the deployment of sorghum forage is influenced by the sowing speed and the soil tillage system used. Chisel plow was the equipment that required the highest mean traction force, mean traction and slip, as well as the lowest mean speed for the studied tillage system. Forage sorghum showed higher yields in no-tillage systems at a seeding speed of 5 km h(-1).

Performance of aerodynamic baffles in cylindrical grinding analyzed on the basis of air layer pressure and speed

Over the years, grinding has been considered one of the most important manufacturing processes. Grinding is a high precision process, and the loss of a single workpiece in this stage of the production is unacceptable, fir the value added to the material is very high due to many processes it has already undergone prior to grinding. This study aims to contribute toward the development of an experimental methodology whereby the pressure and speed of the air layer produced by the high rotation of the grinding wheel is evaluated with and without baffles, i.e., in an optimized grinding operation and in a traditional one. Tests were also carried out with steel samples to check the difference in grinding wheel wear with and without the use of baffles.

Influence of the grinding wheel's dive speed on the damage of rectified hardened steels

The world tendency is the increase of the productivity and the production of pieces more and more sophisticated, with high degree of geometric and dimensional tolerances, with good surface finish and low cost. Rectification is responsible for the final finish in the machining process of a material. However, damages generated in this production phase affect all the resources used in the previous processes. Great part of the problems happennig in the rectification process is due to the enormous temperature generated in this activity because of the machining conditions. The dive speed, which is directly related to the productivity, is considered responsible for the damages that occur during rectification, limiting its values to those that do not cause such damages. In this work, through the variation of the dive speed in the process of cylindrical grinding of type ABNT D6 steel, rationalizing the application of two cutting fluids and using a CBN (cubic boron nitrate) abrasive wheel with vitrified blond, the influence of the dive speed on the surface damages of hardened steels was evaluated. The results allowed to say that the dive speed, associated to an efficient cooling and lubrication, didn't provoke thermal damages (including heated zones, cracks and tension stresses) to the material. Residual stresses and the roughness of rectified materials presented a correlation with the machining conditions. The work concluded that it is possible to increase the productivity without provoking damages in the rectified components.

Influence of belt speed, grit sizes and pressure on the sanding of Eucalyptus grandis wood

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Power performance evaluation of an electric home fan with triac-based automatic speed control system

In order to provide a low cost system of thermal comfort, a common model of home fan, 40 cm diameter size, had its manual four-button control system replaced by an automatic speed control. The new control system has a temperature sensor feeding a microcontroller that, by using an optic coupling, DIAC or TRIAC-based circuit, varies the RMS value of the fan motor input voltage and its speed, according to the room temperature. Over a wide range of velocity, the fan net power and the motor fan input power were measured working under both control system. The temperature of the motor stator and the voltage waveforms were observed too. Measured values analysis showed that the TRIAC-based control system makes the fan motor work at a very low power factor and efficiency values. The worst case is at low velocity range where the higher fan motor stator temperatures were registered. The poor power factor and efficiency and the harmonics signals inserted in the motor input voltage wave by the TRIAC commutation procedure are correlated.

Positive leader characteristics from high-speed video observations

Based on analyses of high-speed video recordings of cloud-to-ground lightning in Brazil and the USA, the characteristics of positive cloud-to-ground (+CG) leaders are presented. The high frame rates permitted the average, 2-dimensional speeds of development along the paths of the channels to be resolved with good accuracy. The values range from 0.3 to 6.0 x 10(5) ms(-1) with a mean of 2.7 x 10(5) ms(-1). Contrary to what is usually assumed, downward +CG leader speeds are similar to downward -CG leader speeds. Our observations also show that the speeds tend to increase by a factor of 1.1 to 6.5 as they approach the ground. The presence of short duration, recoil leaders (RLs) during the development of positive leaders reveal a highly branched structure that is not usually recorded when using conventional photographic and video cameras. The existence of the RLs may help to explain observations of UHF-VHF radiation during the development of +CG flashes.

A novel HPF voltage source rectifier for variable speed refrigeration systems

A novel single-phase voltage source rectifier capable to achieve High-Power-Factor (HPF) for variable speed refrigeration system application, is proposed in this paper. The proposed system is composed by a single-phase high-power-factor boost rectifier, with two cells in interleave connection, operating in critical conduction mode, and employing a soft-switching technique, controlled by a Field Programmable Gate Array (FPGA), associated with a conventional three-phase IGBT bridge inverter (VSI - Voltage Source Inverter), controlled by a Digital Signal Processor (DSP). The soft-switching technique for the input stage is based on zero-current-switching (ZCS) cells. The rectifier's features include the reduction in the input current ripple, the reduction in the output voltage ripple, the use of low stress devices, low volume for the EMI input filter, high input power factor (PF), and low total harmonic distortion (THD) in the input current, in compliance with the EEC61000-3-2 standards. The digital controller for the output stage has been developed using a conventional voltage-frequency control (scalar V/f control), and a simplified stator oriented Vector control, in order to verify the feasibility and performance of the proposed digital controls for continuous temperature control applied at a refrigerator prototype.