Integrating open source codes for solid modeling and automatic mesh generation in FEM applications

The applications of the Finite Element Method (FEM) for three-dimensional domains are already well documented in the framework of Computational Electromagnetics. However, despite the power and reliability of this technique for solving partial differential equations, there are only a few examples of open source codes available and dedicated to the solid modeling and automatic constrained tetrahedralization, which are the most time consuming steps in a typical three-dimensional FEM simulation. Besides, these open source codes are usually developed separately by distinct software teams, and even under conflicting specifications. In this paper, we describe an experiment of open source code integration for solid modeling and automatic mesh generation. The integration strategy and techniques are discussed, and examples and performance results are given, specially for complicated and irregular volumes which are not simply connected. © 2011 IEEE.

An open source GPS multipath simulator in Matlab/Octave

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sperm motility parameters for Steindachneridion parahybae based on open-source software

Summary: The objective of this work was to evaluate the sperm motility of 13 Steindachneridion parahybae males using open-source software (ImageJ/CASA plugin). The sperm activation procedure and image capture were initiated after semen collection. Four experimental phases were defined from the videos captured of each male as follows: (i) standardization of a dialogue box generated by the CASA plugin within ImageJ; (ii) frame numbers used to perform the analysis; (iii) post-activation motility between 10 and 20 s with analysis at each 1 s; and (iv) post-activation motility between 10 and 50 s with analysis at each 10 s. The settings used in the CASA dialogue box were satisfactory, and the results were consistent. These analyses should be performed using 50 frames immediately after sperm activation because spermatozoa quickly lose their vigor. At 10 s post-activation, 89.1% motile sperm was observed with 107.2 μm s-1 curvilinear velocity, 83.6 μm s-1 average path velocity, 77.1 μm s-1 straight line velocity; 91.6% were of straightness and 77.1% of wobble. The CASA plugin within ImageJ can be applied in sperm analysis of the study species by using the established settings. © 2013 Blackwell Verlag GmbH.

Uma proposta de desenvolvimento de laboratório remoto de automação e acionamento de máquinas elétricas para uso didático, utilizando software open source

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Delaunay Tetrahedralization of the Heart Based on Integration of Open Source Codes

The Finite Element Method (FEM) is a way of numerical solution applied in different areas, as simulations used in studies to improve cardiac ablation procedures. For this purpose, the meshes should have the same size and histological features of the focused structures. Some methods and tools used to generate tetrahedral meshes are limited mainly by the use conditions. In this paper, the integration of Open Source Softwares is presented as an alternative to solid modeling and automatic mesh generation. To demonstrate its efficiency, the cardiac structures were considered as a first application context: atriums, ventricles, valves, arteries and pericardium. The proposed method is feasible to obtain refined meshes in an acceptable time and with the required quality for simulations using FEM.

Entropy effect in quantum computing and information: an open-source environment simulation

The technologies are rapidly developing, but some of them present in the computers, as for instance their processing capacity, are reaching their physical limits. It is up to quantum computation offer solutions to these limitations and issues that may arise. In the field of information security, encryption is of paramount importance, being then the development of quantum methods instead of the classics, given the computational power offered by quantum computing. In the quantum world, the physical states are interrelated, thus occurring phenomenon called entanglement. This study presents both a theoretical essay on the merits of quantum mechanics, computing, information, cryptography and quantum entropy, and some simulations, implementing in C language the effects of entropy of entanglement of photons in a data transmission, using Von Neumann entropy and Tsallis entropy.

Tolerância a falha em um ambiente de computação em nuvem open source

Pós-graduação em Ciência da Computação - IBILCE

Determination of minimum fluidization velocity for gas-solid beds by experimental data and numerical simulations

The purpose of this work is to predict the minimum fluidization velocity Umf in a gas-solid fluidized bed. The study was carried out with an experimental apparatus for sand particles with diameters between 310μm and 590μm, and density of 2,590kg/m3. The experimental results were compared with numerical simulations developed in MFIX (Multiphase Flow with Interphase eXchange) open source code [1], for three different sizes of particles: 310mum, 450μm and 590μm. A homogeneous mixture with the three kinds of particles was also studied. The influence of the particle diameter was presented and discussed. The Ergun equation was also used to describe the minimum fluidization velocity. The experimental data presented a good agreement with Ergun equation and numerical simulations. Copyright © 2011 by ASME.

Three-dimensional modeling and highly refined mesh generation of the aorta artery and its tunics

This paper describes strategies and techniques to perform modeling and automatic mesh generation of the aorta artery and its tunics (adventitia, media and intima walls), using open source codes. The models were constructed in the Blender package and Python scripts were used to export the data necessary for the mesh generation in TetGen. The strategies proposed are able to provide meshes of complicated and irregular volumes, with a large number of mesh elements involved (12,000,000 tetrahedrons approximately). These meshes can be used to perform computational simulations by Finite Element Method (FEM). © Published under licence by IOP Publishing Ltd.

A development process proposal for the ERP5 system

Modeling ERP software means capturing the information necessary for supporting enterprise management. This modeling process goes down through different abstraction layers, from enterprise modeling to code generation. Thus ERP is the kind of system where enterprise engineering undoubtedly has, or should have, a strong influence. For the case of Free/Open Source ERP, the lack of proper modeling methods and tools can jeopardize the advantage brought by source code availability. Therefore, the aim of this paper is to present a development process proposal for the Open Source ERP5 system. The proposed development process aims to cover different abstraction levels, taking into account well established standards and common practices, as well as platform issues. Its main goal is to provide an adaptable meta-process to ERP5 adopters. © 2006 IEEE.

Enterprise systems modeling: The ERP5 development process

The design and implementation of an ERP system involves capturing the information necessary for implementing the system's structure and behavior that support enterprise management. This process should start on the enterprise modeling level and finish at the coding level, going down through different abstraction layers. For the case of Free/Open Source ERP, the lack of proper modeling methods and tools jeopardizes the advantages of source code availability. Moreover, the distributed, decentralized decision-making, and source-code driven development culture of open source communities, generally doesn't rely on methods for modeling the higher abstraction levels necessary for an ERP solution. The aim of this paper is to present a model driven development process for the open source ERP ERP5. The proposed process covers the different abstraction levels involved, taking into account well established standards and common practices, as well as new approaches, by supplying Enterprise, Requirements, Analysis, Design, and Implementation workflows. Copyright 2008 ACM.

Sistema WEB para gerenciamento de informações agrícolas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Estudo numérico de modelos de arrasto e do coeficiente de restituição no escoamento gás-sólido em leito fluidizado

Pós-graduação em Engenharia Mecânica - FEG

Gerenciamento integrado de rede local com software livre

Pós-graduação em Engenharia Elétrica - FEIS