Si-based thin film coating on Y-TZP: Influence of deposition parameters on adhesion of resin cement

This study evaluated the influence of deposition parameters for Si-based thin films using magnetron sputtering for coating zirconia and subsequent adhesion of resin cement. Zirconia ceramic blocks were randomly divided into 8 groups and specimens were either ground finished and polished or conditioned using air-abrasion with alumina particles coated with silica. In the remaining groups, the polished specimens were coated with Si-based film coating with argon/oxygen magnetron discharge at 8:1 or 20:1 flux. In one group, Si-based film coating was performed on air-abraded surfaces. After application of bonding agent, resin cement was bonded. Profilometry, goniometry, Energy Dispersive X-ray Spectroscopy and Rutherford Backscattering Spectroscopy analysis were performed on the conditioned zirconia surfaces. Adhesion of resin cement to zirconia was tested using shear bond test and debonded surfaces were examined using Scanning Electron Microscopy. Si-based film coating applied on air-abraded rough zirconia surfaces increased the adhesion of the resin cement (22.78 ± 5.2 MPa) compared to those of other methods (0-14.62 MPa) (p = 0.05). Mixed type of failures were more frequent in Si film coated groups on either polished or air-abraded groups. Si-based thin films increased wettability compared to the control group but did not change the roughness, considering the parameters evaluated. Deposition parameters of Si-based thin film and after application of air-abrasion influenced the initial adhesion of resin cement to zirconia. © 2013 Elsevier B.V. All rights reserved.

Preparation of SrBi2Ta2O9 ferroelectric thick films by electrophoretic deposition using aqueous suspensions

SrBi2Ta2O9 ferroelectric thick films were prepared by electrophoretic deposition (EPD). For that, ceramic powders were prepared by chemical method in order to obtain compounds with chemical homogeneity. The polymeric precursor method was used for the synthesis of the SrBi2Ta2O9 powder. The crystallographic structure of the powder was examined by X-ray diffraction, and the surface area was determined by single point BET adsorption. The 0.03 vol% suspension was formed by dispersing the powder in water using two different polymers as dispersants: an ester polyphosphate (C213) and an ammonium polyacrilate (Darvan 821-A). The influence of the different dispersants on the powder surface properties were investigated by zeta potential measurements. The films were deposited on platinum-coated alumina and Pt/Ti/SiO2/Si substrates by electrophoretic deposition using a 4 mA constant current, for 10 min, with two parallel electrodes placed at a separation distance of 3 min in the suspension. Several cycles of deposition-drying of the deposit was carried out until the desired thickness was obtained. After thermal treatment at temperatures ranging from 700 to 1000degreesC, the films were characterized by X-ray diffraction and scanning electron microscopy.

Aerosol Deposition of Ba0.8Sr0.2TiO3 Thin Films

In this work we optimized conditions for aerosol deposition of homogeneous, nano-grained, smooth Ba0.8Sr0.2TiO3 thin films. Investigation involved optimization of deposition parameters, namely deposition time and temperature for different substrates. Solutions were prepared from titanium isopropoxide, strontium acetate and barium acetate. Films were deposited on Si (1 0 0) or Si covered by platinum (Pt (1 1 1) /Ti/SiO2/Si). Investigation showed that the best films were obtained at substrate temperature of 85 degrees C. After deposition films were slowly heated up to 650 degrees C, annealed for 30 min, and slowly cooled. Grain size of BST films deposited on Si substrate were in the range 40-70 nm, depending on deposition conditions, while the same films deposited on Pt substrates showed mean grain size in the range 35-50 nm. Films deposited under optimal conditions were very homogeneous, crack-free, and smooth with rms roughness lower than 4 nm for both substrates.

Aspectos clínicos e patológicos em frangos de corte (Gallus gallus domesticus) infectados experimentalmente com oocistos esporulados de Eimeria acervulina Tyzzer, 1929

No presente estudo, sinais clínicos e alterações patológicas foram avaliados por 30 dias em frangos de corte, linhagem Cobb, machos, com dez dias de idade, infectados com Eimeria acervulina. Foram utilizados 192 animais distribuídos em 3 grupos: grupo A inoculado com 1x10(6) oocistos esporulados; grupo B inoculado com 1x10(5) oocistos esporulados; grupo C inoculado com água destilada. Os sinais clínicos observados foram anorexia, diarréia e apatia. As alterações patológicas macroscópicas observadas foram: enterite, hiperemia seguido de congestão intestinal, excesso de exsudato mucoso no lúmen do intestino delgado, palidez e desidratação muscular, alto acúmulo de bile na vesícula biliar e deposição de gordura hepática. A atrofia de vilosidades e alta presença de células inflamatórias foram as alterações microscópicas observadas no epitélio intestinal. Na análise histopatológica do fígado observaram-se infiltrados inflamatórios e deposição de gordura. Os resultados demonstraram que frangos de corte infectados experimentalmente com E. acervulina apresentam progressivas lesões intestinais de intensidade variável e que essas anormalidades são as principais causas de redução no desenvolvimento da ave.

Voltammetric characteristics of miconazole and its cathodic stripping voltammetric determination

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Compact disks, a new source for gold electrodes. Application to the quantification of copper by PSA

In this work we describe a versatile and very sensitive way for copper quantification by potentiometric stripping analysis using gold electrodes obtained from recordable compact disks (CDs). This new source of electrodes (CDtrodes) shown similar performance to the commercial gold electrodes with superior versatility and lower cost. Recordable CDs contains a highly pure gold film with thickness between 50 and 100 nm and superficial area of ca. 100 cm(2). The working electrode developed was used successfully in stationary cell and many experimental parameters have been optimized. For copper, the detection limit attained was 30 ng L-1 (600 s deposition time) with remarkable precision (standard deviation of 1.8 % for 20 repetitive measurements using 25 mu gL(-1) of copper with 60 s of deposition time). The gold electrode developed was used for analysis of copper in sugar cane spirits and tap water samples. The results were compared with those obtained by atomic absorption spectroscopy.

SrBi2Ta2O9 ferroelectric thick films prepared by electrophoretic deposition using aqueous suspension

SrBi2Ta2O9 ferroelectric thick films were prepared by electrophoretic deposition (EPD). For that, ceramic powders were prepared by chemical method in order to obtain compounds with chemical homogeneity. The polymeric precursor method was used for the synthesis of the SrBi2Ta2O9 powder. The crystallographic structure of the powder was examined by X-ray diffraction, and the surface area was determined by single point BET adsorption. The 0.03 vol.% suspension was formed by dispersing the powder in water using two different polymers as dispersants: an ester polyphosphate (C213) and an ammonium polyacrilate (Darvan 821-A). It was investigated the influence of the different dispersants in the surface properties of the powder by zeta potential measurements. The films were deposited on platinum-coated alumina and Pt/Ti/SiO2/Si substrates by a 4 mA constant current, for 10 min, using two parallel electrodes placed at a separation distance of 3 min in the suspension. Several cycles of deposition-drying of the deposit were carried out until reaching the desired thickness. After thermal treatment at temperatures ranging from 700 to 1000 degreesC, the films were characterized by X-ray diffraction and scanning electron microscopy for the microstructure observation. (C) 2003 Elsevier Ltd. All rights reserved.

Preparation of Fe-Cr-P-Co amorphous alloys by electrodeposition

The effects of bath composition and electroplating conditions on structure, morphology, and composition of amorphous Fe-Cr-P-Co deposits on AISI 1020 steel substrate, priorly plated with a thin Cu deposit, were investigated. The increase of charge density activates the inclusion of Cr in the deposit. However, above specific values of the charge density, which depend on the deposition current density, the Cr content in the deposit decreases. This Cr content decreasing is probably due to the significant hydrogen evolution with the increasing of deposition cur-rent and charge density. The effect of charge density on the content of Fe and Co is not clear. However, there is a tendency of increasing of Fe content and decreasing of Co content with the raising of current density. The Co is more easily deposited than the P, and its presence results in a more intense inhibition effect on the Cr deposition than the inhibition effect caused by P presence. Scanning electron microscope (SEM) analysis showed that Co increasing in the Fe-Cr-P-Co alloys analyzed does not promote the susceptibility to microcracks, which led to a good quality deposit. The passive film of the Fe-Cr-P-Co alloy shows a high ability formation and high protective capacity, and the results obtained by current density of corrosion, j(cor), show that the deposit with addition of Co, Fe31Cr11P28Co30, presents a higher corrosion resistance than the deposit with addition of Ni, Fe54Cr21P20Ni5. (C) 2004 Published by Elsevier B.V.

A study of different calcification areas in newly formed bone 8 weeks after insertion of dental implants in rabbit tibias

In orofacial implantology there are many types of implants for the different systems. Among these is the implant surface type, e.g., a screw type, cylindrical and laminar. Furthermore, the implants are different in their dimensions, their metal composition, their surface condition, such as smooth, grit or layered surfaces and in their methods of application. Two different self-tapping implants, one smooth and the other grit-blasted, are screwed into the bone, and another one with a plasma of titanium coating, which is also in a screw form but with greater spaces between the screw threads are compared. The greatest amount of bone deposition in the bone/implant interface was encountered in the latter one, the smooth surfaced implant being in second place. All of these systems can alter the implant healing process and to demonstrate this, we injected bone markers in the rabbits over different periods of time so as to observe the different areas of bone deposition in the tibias where the implants had been inserted. The bone tracers used were Alizarin, Calcein and Xylenol-orange. The amount of deposition was calculated by using the method of surface morphometry.

The significance and determination by image analysis of microcrack density in hard chromium plating

It is well known that the microcrack density is a fundamental parameter in hard chromium electroplating. The chemical and mechanical properties of this coating are widely dependent on its microcrack density. In this paper a simple image analysis procedure to determine microcrack density is presented in order to demonstrate it as a fundamental tool to estimate the fatigue, corrosion and wear behavior, as well as the residual stress field of a coated component. For this purpose, the image analysis procedure was carried out on two kinds of hard chromium plating - one called accelerated (high velocity of deposition and fluoride-free) and the other conventional (with fluoride). The coatings were applied on samples of AISI 4340 aeronautical steel, which is widely used in aircraft landing gear components. To characterize the practical significance of this study, the microcrack density results were related to the fatigue, wear and corrosion behavior from previous study and to the residual stress field in the coatings.

Aplicação do eletrocapilaridade na manipulação de microgotas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ácaro da mancha-anular do cafeeiro: controle em função da cobertura pela calda com ramais e volumes de aplicação

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Ganhos de peso, taxas de deposição e composição química corporal de tourinhos Santa Gertrudes confinados, recebendo alto concentrado e níveis crescentes de polpa cítrica peletizada

Objetivou-se avaliar a substituição do milho em grão pela polpa cítrica peletizada e seus efeitos sobre os ganhos de peso, as taxas de deposição e a composição química corporal de tourinhos Santa Gertrudes em confinamento. Vinte e oito animais (idade média de nove meses e peso inicial de 277 kg) foram mantidos em baias individuais durante 92 dias, após 21 dias de adaptação. Os animais receberam dietas contendo 20% da MS como silagem de milho que continha 40% de grãos. Foram testados os níveis de 0, 25, 40 e 55% de participação da polpa cítrica peletizada na MS da dieta. A composição química corporal foi estimada a partir de equações desenvolvidas para a mesma raça, utilizando-se a composição química do corte da 9-10-11ª costelas. A participação da polpa cítrica peletizada não afetou significativamente o peso corporal final (449 kg) e os ganhos diários de peso corporal (1,50 kg), de corpo vazio (1,26 kg) e de carcaça (0,78 kg). Não houve diferença entre tratamentos para as taxas diárias de deposição de água (0,374 kg), EE (0,589 kg), proteína (0,253 kg), minerais (0,040 kg) e energia (6,934 Mcal) e, conseqüentemente, a composição química corporal final foi similar entre os animais recebendo diferentes níveis de polpa cítrica na dieta. A substituição do milho em grão por polpa cítrica peletizada, até 55% da MS, em dietas para tourinhos em terminação recebendo altos níveis de concentrado, não altera os ganhos de peso, as taxas de deposição e a composição química corporal desses animais.

Velocidade do ar em barra de pulverização na deposição da calda fungicida, severidade da ferrugem asiática e produtividade da soja

O trabalho objetivou comparar a deposição da pulverização e o controle da ferrugem asiática após o tratamento com fungicidas sob quatro velocidades da assistência de ar junto à barra de pulverização na cultura da soja. Dois experimentos foram conduzidos na FCA/UNESP - Campus de Botucatu, safra 2006/07. Alvos artificiais foram fixados na superfície adaxial e abaxial de folíolos posicionados nas partes superior e inferior das plantas selecionadas e distribuídas perpendicularmente ao deslocamento do pulverizador. O oxicloreto de cobre (50% de cobre metálico) foi o marcador utilizado em pulverização e a determinação quantitativa dos depósitos feita com o uso de espectrofotometria de absorção atômica. Após a aplicação do fungicida piraclostrobina + epoxiconazole sob diferentes velocidades da assistência de ar junto à barra de pulverização (0, 9, 11 e 29 km h-1) procedeu-se a avaliação da severidade da doença e produtividade da soja. Na parte superior das plantas os maiores níveis de depósitos foram encontrados na pulverização sem assistência de ar. Já na parte inferior da planta foram encontrados os maiores níveis de deposição quando foram utilizadas as maiores velocidades da assistência de ar. No geral, a severidade da doença foi mais acentuada nos tratamentos sem o uso da assistência de ar. em relação à produtividade não houve diferenças entre os tratamentos com aplicação de fungicidas, porém houve incremento na produtividade para os tratamentos com assistência de ar.

Assistência de ar e volumes de aplicação na deposição de calda e no controle do arroz vermelho (Oryza sativa L.)

O trabalho teve como objetivo avaliar o efeito da assistência de ar junto à barra pulverizadora e de três volumes de pulverização na dessecação e deposição da calda em arroz vermelho, sob cultivo de nabo forrageiro, em áreas de recuperação de várzeas, utilizando o herbicida paraquat e o corante Azul Brilhante, respectivamente. Os volumes de pulverização foram 100; 200 e 300 L ha-1 da solução aquosa, contendo corante alimentício (1.500 mg L-1). Com ou sem a assistência de ar junto à barra, foram utilizadas pontas de pulverização de jato plano tipo AXI 110015 à pressão de 117,3 kPa, AXI 11002 e AXI 11003 a 276 kPa. A avaliação da deposição da pulverização deu-se em folhas de plantas de arroz vermelho. Os maiores volumes (200 e 300 L ha-1) pulverizados com a assistência de ar junto à barra pulverizadora proporcionaram maiores depósitos do corante em relação ao volume de 100 L ha-1. Não foram constatadas diferenças na deposição do corante para os volumes pulverizados, sem a assistência de ar junto à barra, tampouco entre os volumes de 200 e 300 L ha-1 com a assistência de ar junto à barra. As maiores percentagens de controle do arroz vermelho foram obtidas com a assistência de ar junto à barra, independentemente do volume pulverizado, equivalendo-se ao controle obtido com 300 L ha-1, sem o uso dessa tecnologia.