Biological and DNA evidence of two dissimilar populations of the Rhipicephalus sanguineus tick group (Acari : Ixodidae) in South America

In this work, the biology, mitochondrial DNA and fertility of hybrids from two strains of Rhipicephalus sanguineus, from Brazil and Argentina, were compared. Engorged larvae, nymphs and adults from Argentina weighed more and the engorgement period of adult females was significantly longer than those of their Brazilian counterparts, whereas adult female tick yield rate was higher for the Brazilian strain. High intraspecific divergence of mitochondrial DNA was detected between R. sanguineus from Brazil and Argentina. on the other hand, a strong genetic relationship was detected between European and Argentinean R. sanguineus populations while the Brazilian population appeared to be related to the African Rhipicephalus turanicus. Adult hybrid females laid eggs, which were mostly unviable, whereas a mean of more than 1400 larvae hatched per egg mass from pure Brazilian and Argentinean strains. These results showed that differences between these strains are greater than previously assumed and that the biosysternatic status of R. sanguineus ticks from South America should be re-evaluated. Wide variations, such as these might account for the reported worldwide differences in biology and vector capacity of this species. (c) 2005 Elsevier B.V. All rights reserved.

Organophosphate induced delayed neuropathy in genetically dissimilar chickens: Studies with tri-ortho-cresyl phosphate (TOCP) and trichlorfon

Measurements of plasma cholinesterase (pl.ChE), brain cholinesterase (Br.ChE) and brain Neuropathy Target Esterase (Br.NTE) were made in three different lineages of chickens. All birds received toxicants through gavage in a single oral dose between 08:00 and 09:00 h, after overnight fast. Babcock chickens were treated with 800 mg/kg tri-ortho-cresyl phosphate (TOCP) or 80 mg/kg trichlorfon. The TOCP group had 82% Br.NTE inhibition, when compared to the control group, and no birds displayed symptoms of clinical organophosphate-induced delayed neuropathy (OPIDN). Hy-line w36 lineage chickens were given 1600 mg/kg TOCP and despite this higher dose, Br.NTE inhibition was similar that presented by Babcock chickens. Isabrown chickens were given 1600 mg/kg TOCP or 80 mg/kg trichlorfon. At 36 h all trichlorfon treated birds had from 80 to 90% inhibition of Pl.ChE and Br.ChE, when compared to controls. However, Br.NTE was inhibited less than 20%, and there were no clinical signs of OPIDN. All TOCP treated isabrown chickens had more than 80% Br.NTE inhibition while one of them exhibited just light signs of OPIDN, two chickens became totally paralyzed. This finding suggested that chicken strain was important in the appearance of OPIDN. In addition, 70-80% of NTE inhibition was necessary but was not sufficient to produce OPIDN in chickens, since babcock and hy-line w36 chickens exhibited NTE inhibition in the range of 70-80% without clinical signs of OPIDN. © 2002 Elsevier Science Ireland Ltd. All rights reserved.

Preferential infection sites of Cysticercus bovis in cattle experimentally infected with Taenia saginata eggs

The preferential sites of infection of Cysticercus bovis were evaluated in the skeletal muscle and entrails of 25 cattle that were experimentally infected with Taenia saginata (2 x 10(4) eggs). Two other animals were not inoculated (control). Ninety days after inoculation, all the cattle were euthanized. The carcasses were deboned and dissected into 26 anatomical sections (masseter muscles, brain, tongue, esophagus, heart, diaphragm, lungs, liver, kidneys, spleen, top sirloin butt, bottom sirloin butt, outside round, top (inside) round, transversus abdominus, top sirloin cap, strip loin, full tenderloin, eye of round, knuckle, shoulder clod, foreshank, shank, chuck, back ribs, and tail muscles). The dissected tissues were sliced into 5 mm sections. From the 25 cattle, 9258 C. bovis (cysticerci) were recovered; 75.02% (6946) of these were recovered from skeletal muscles and 24.98% (2312) from the entrails. A high parasitism level was found in the shoulder clod (12.55%), heart (11.02%), liver (9.48%), masseter muscles (8.51%), chuck (8.25%), strip loin and full tenderloin (7.26%), knuckle (6.63%), and back ribs (5.53%), totaling 69.23% (5738) of all of the detected cysticerci. on the other hand, there was a low C. bovis parasitism level in the brain, spleen, tail muscles, kidneys, esophagus, and diaphragm, representing just 3.9% of the total number of cysticerci. Given these results, we conclude that specific skeletal musculature regions, such as the shoulder blade, chuck, strip loin and full tenderloin, knuckle, back ribs and top round, which are not officially examined in many countries, are effective sites to efficiently screen C. bovis infection. To date, these regions have not been considered as preferential sites of C. bovis infection. Based on our work, however, these regions deserve greater attention from health inspectors because they contained a greater number of Cysticercus than the other regions of carcasses that are parasitized by T. saginata larvae. (c) 2010 Elsevier Ltd. All rights reserved.

Divergência genética de cultivares de arroz quanto à resistência a Tibraca limbativentris Stål (Hemiptera: Pentatomidae)

A divergência genética de 16 cultivares de arroz quanto à resistência ao percevejo-do-colmo-do-arroz, Tibraca limbativentris Stål, foi avaliada por meio de técnicas de análise multivariada. O experimento foi conduzido em casa de vegetação, em delineamento experimental de blocos ao acaso, com oito repetições. Na avaliação foram considerados oito caracteres de resistência ao ataque do inseto. A divergência genética foi avaliada por procedimentos multivariados: distância generalizada de Mahalanobis (D²), método de agrupamento de otimização de Tocher e técnica de variáveis canônicas. As cultivares mais dissimilares foram Bico Ganga e Marabá Branco, enquanto Agulha e Branco Tardão foram as mais similares. Foram formados cinco grupos pelo método de otimização de Tocher. As três primeiras variáveis canônicas explicaram 88,5% da variabilidade total disponível. Conclui-se que as técnicas de análise multivariada são eficientes para a análise da divergência genética entre as cultivares de arroz, com destaque para Marabá Branco e Bico Ganga, consideradas as mais promissoras a serem utilizadas em futuros cruzamentos para melhoramento visando resistência ao percevejo-do-colmo-do-arroz.

Strains of Xylella fastidiosa rapidly distinguished by arbitrarily primed-PCR

Genomic DNAs isolated from strains of Xylella fastidiosa that caused citrus variegated chlorosis, coffee leaf scorch, Pierce's Disease of grapevine, and plum leaf scorch were analyzed by arbitrarily primed polymerase chain reaction. Purified DNA was amplified under nonstringent conditions with single primers 21 nucleotides (nt) long. Thirty-nine amplification products were observed that were useful to distinguish among the strains and to derive a similarity matrix and construct a phenogram showing possible relationships among the strains. Strains isolated from diseased coffee and citrus in Brazil were closely related to each other (coefficient of similarity of 0.872), but only distantly related to a strain isolated from diseased grapevine in the USA (coefficient of similarity of 0.650). Strains of Xylella fastidiosa isolated from diseased plums in the USA and Brazil clustered with strains from different hosts isolated from their respective countries of origin. Thus, there may be two quite dissimilar clusters of strains of Xylella fastidiosa, one in North America and the other in South America. Each cluster contains strains that can cause disease in plum. The methods described provide a convenient and rapid method to distinguish between strains of Xylella fastidiosa that cause diseases of coffee and citrus in the same region of Brazil. This has not been possible previously. This will potentially enable the two strains to be distinguished in alternate hosts or in insect vectors.

Influência do tipo de chanfro, tecimento e sentido de laminação na distorção angular em soldagem GMAW-P robotizada de alumínio

The industry's interest in having a greater control of the deformations caused by welding is due to the geometric and dimensional tolerances been more and more precise in the project specifications, motivating the manufacturing engineering to develop stable processes and to ensure routine production. Aiming at it, the main goal of this present work is to analyze how much routine situations used in automatic aluminum welding can influence on the angular deformations of this material. Using the alloy AA 5052 H34, and the automatic welding in pulsed GMAW process, three types of weaving were applied throughout the length of the weld, in butt joints assembled without groove and with 60 degrees single-V-groove, arranged transversely as well as longitudinally to the rolling direction of the plate. The measurement of the deformations was made by a three-dimensional equipment, before and after the welding, in three distinct regions in the specimens. The profile of the weld bead was the main factor for the different types of deformations found, as revealed by macrographical analysis. The 60 degrees single-V-groove had higher amplitudes of deformations as the joint without groove. The torch oscillation wasn't a variable of statistically significant influence on this amplitudes.

Digital radiography using digital detector arrays fulfills critical applications for offshore pipelines

Digital radiography in the inspection of welded pipes to be installed under deep water offshore gas and oil pipelines, like a presalt in Brazil, in the paper has been investigated. The aim is to use digital radiography for nondestructive testing of welds as it is already in use in the medical, aerospace, security, automotive, and petrochemical sectors. Among the current options, the DDA (Digital Detector Array) is considered as one of the best solutions to replace industrial films, as well as to increase the sensitivity to reduce the inspection cycle time. This paper shows the results of this new technique, comparing it to radiography with industrial films systems. In this paper, 20 test specimens of longitudinal welded pipe joints, specially prepared with artificial defects like cracks, lack of fusion, lack of penetration, and porosities and slag inclusions with varying dimensions and in 06 different base metal wall thicknesses, were tested and a comparison of the techniques was made. These experiments verified the purposed rules for parameter definitions and selections to control the required digital radiographic image quality as described in the draft international standard ISO/DIS 10893-7. This draft is first standard establishing the parameters for digital radiography on weld seam of welded steel pipes for pressure purposes to be used on gas and oil pipelines.

Pulsed Nd:YAG laser seam welding of AISI 316L stainless steel thin foils

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Micro Welding of Ni-based Alloy Monel 400 Thin Foil by Pulsed Nd:YAG laser

In this study a pulsed Nd:YAG laser was used to join Monel 400 thin foil with 100 mu m thickness. Pulse energy was varied from 1.0 to 2.25J at small increments of 0.25J. The macro and microstructures were analyzed by optical microscopy, tensile shear test and microhardness. Sound laser welds without discontinuities were obtained with 1.5 J pulse energy. Results indicate that using a precise control of the pulse energy, and so a control of the bottom foil dilution rate, it is possible to weld Monel 400 thin foil. The process appeared to be very sensitive to the gap between couples.

Pulsed Nd:YAG laser welding of Ni-alloy Hastelloy C-276 foils

In this study a pulsed Nd:YAG laser was used to join Hastelloy C-276 thin foil with 100 microns thickness. Pulse energy was varied from 1.0 to 2.25 J at small increments of 0.25 J with a 4 ms pulse duration. The macro and microstructures of the welds were analyzed by optical and electronic microscopy, tensile shear test and microhardness. Sound laser welds without discontinuities were obtained with 1.5 J pulse energy. Results indicate that using a precise control of the pulse energy, and so a control of the dilution rate, it is possible to weld Hastelloy C-276 thin foil by pulsed Nd: YAG laser. (C) 2012 Published by Elsevier B. V. Selection and/or review under responsibility of Bayerisches Laserzentrum GmbH

Influence of Microgap Location and Configuration on Radiographic Bone Loss Around Submerged Implants: An Experimental Study in Dogs

Purpose: The vertical location of the implant-abutment connection influences the subsequent reaction of the peri-implant bone. It is not known, however, whether any additional influence is exerted by different microgap configurations. Therefore, the radiographic bone reactions of two different implant systems were monitored for 6 months. Materials and Methods: In eight mongrel dogs, two implants with an internal Morse-taper connection (INT group) were placed on one side of the mandible; the contralateral side received two implants with an external-hex connection (EXT group). on each side, one implant was aligned at the bone level (equicrestal) and the second implant was placed 1.5 mm subcrestal. Healing abutments were placed 3 months after submerged healing, and the implants were maintained for another 3 months without prosthetic loading. At implant placement and after 1, 2, 3, 4, 5, and 6 months, standardized radiographs were obtained, and peri-implant bone levels were measured with regard to microgap location and evaluated statistically. Results: All implants osseointegrated clinically and radiographically. The overall mean bone loss was 0.68 +/- 0.59 mm in the equicrestal INT group, 1.32 +/- 0.49 mm in the equicrestal EXT group, 0.76 +/- 0.49 mm in the subcrestal INT group, and 1.88 +/- 0.81 mm in the subcrestal EXT group. The differences between the INT and EXT groups were statistically significant (paired t tests). The first significant differences between the internal and external groups were seen at month 1 in the subcrestal groups and at 3 months in the equicrestal groups. Bone loss was most pronounced in the subcrestal EXT group. Conclusions: Within the limits of this study, different microgap configurations can cause different amounts of bone loss, even before prosthetic loading. Subcrestal placement of a butt-joint microgap design may lead to more pronounced radiographic bone loss. INT J ORAL MAXILLOFAC IMPLANTS 2011;26:941-946

Influence of Microgap Location and Configuration on Radiographic Bone Loss in Nonsubmerged Implants: An Experimental Study in Dogs

Purpose: The implant-abutment connection (microgap) influences the pen-implant bone morphology. However, it is unclear if different microgap configurations additionally modify bone reactions. This preliminary study aimed to radiographically monitor pen-implant bone levels in two different microgap configurations during 3 months of nonsubmerged healing. Materials and Methods: Six dogs received two implants with internal Morse taper connection (INT group) on one side of the mandible and two implants with external-hex connection (EXT group) on the other side. One implant on each side was positioned at bone level (equicrestal); the second implant was inserted 1.5 mm below the bone crest (subcrestal). Healing abutments were attached directly after implant insertion, and the implants were maintained for 3 months without prosthetic loading. At implant placement and 1, 2, and 3 months, standardized radiographs were taken to monitor pen-implant bone levels. Results: All implants osseointegrated. A total bone loss of 0.48 +/- 0.66 mm was measured in the equicrestal INT group, 0.69 +/- 0.43 mm in the equicrestal EXT group, 0.79 +/- 0.93 mm in the subcrestal INT group, and 1.56 +/- 0.53 mm in the subcrestal EXT group (P>.05, paired t tests). Within the four groups, bone loss over time became significantly greater in the EXT groups than in the INT groups. The greatest bone loss was noted in the subcrestal EXT group. Conclusion: Within the limits of this animal study, it seems that even without prosthetic loading, different microgap configurations exhibit different patterns of bone loss during nonsubmerged healing. Subcrestal positioning of an external butt joint microgap may lead to faster radiographic bone loss. Int J Prosthodont 2011;24:445-452.

Mechanical Strength and Analysis of Fracture of Titanium Joining Submitted to Laser and Tig Welding

This study compared the tensile strength and fracture mechanism of tungsten inert gas (TIG) welds in cylindrical rods of commercially pure titanium (cp Ti) with those of laser welds and intact samples. Thirty dumbbell-shaped samples were developed by using brass rods as patterns. The samples were invested in casings, subjected to thermal cycles, and positioned in a plasma arc welding machine under argon atmosphere and vacuum, and titanium was injected under vacuum/pressure. The samples were X-rayed to detect possible welding flaws and randomly assigned to three groups to test the tensile strength and the fracture mechanism: intact, laser welding, and TIG welding. The tensile test results were investigated using ANOVA, which indicated that the samples were statistically similar. The fracture analysis showed that the cpTi samples subjected to laser welding exhibited brittle fracture and those subjected to TIG welding exhibited mixed brittle/ductile fracture with a predominance of ductile fracture with the presence of microcavities and cleavage areas. Intact samples presented the characteristic straightening in the fracture areas, indicating the ductility of the material.

Partitioning the relative fitness effects of diet and trophic morphology in the threespine stickleback

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Tendency towards homogenization in fish assemblages in the cascade reservoir system of the Tiete river basin, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)