A BEM formulation for analysing the coupled stretching-bending problem of plates reinforced by rectangular beams with columns defined in the domain

In this work, a boundary element formulation to analyse plates reinforced by rectangular beams, with columns defined in the domain is proposed. The model is based on Kirchhoff hypothesis and the beams are not required to be displayed over the plate surface, therefore eccentricity effects are taken into account. The presented boundary element method formulation is derived by applying the reciprocity theorem to zoned plates, where beams are treated as thin sub-regions with larger rigidities. The integral representations derived for this complex structural element consider the bending and stretching effects of both structural elements working together. The standard equilibrium and compatibility conditions along interface are naturally imposed, being the bending tractions eliminated along interfaces. The in-plane tractions and the bending and in-plane displacements are approximated along the beam width, reducing the number of degrees of freedom. The columns are introduced into the formulation by considering domain points where tractions can be prescribed. Some examples are then shown to illustrate the accuracy of the formulation, comparing the obtained results with other numerical solutions.

Nitrification processes in groundwaters evidenced by modification on the U contents and U-234/U-238 activity ratios

Groundwaters from the Botucatu-Piramboia aquifer system located at the Parana sedimentary basin in Brazil and sampled at Ribeirao Preto city, São Paulo State, were chemically and isotopically analysed, with the aim of evaluating how uranium isotopes U-234 and U-238 can be utilized to monitor the progress of nitrate, the main indicator of agrichemical pollution into an aquifer. Based on the isotope dilution analysis, the U-234/U-238 activity ratio and U content data in the groundwaters were utilized to deduce their proportions in a mixture, suggesting that the water not affected significantly by nitrification still dominates the exploitation system involving the studied wells.

Uranium in groundwaters from Botucatu-Piramboia aquifer, Brazil

Groundwater from 60 pumped tubular wells of the Botucatu-Piramboia aquifer system located at the Parana sedimentary basin in Brazil were chemically analysed with the aim of evaluating if the mechanisms related to the migration of uranium can generate concentrations greater than the maximum permissible limit in drinking water, as defined by the Brazilian national standards.

Health risk related to radon in a thermal spa utilizing waters from Guarani aquifer

This investigation was carried out within the Parana sedimentary basin, Brazil, involved the sampling of groundwater and air, and was realized with the purpose of evaluating the radioactivity, due to radon gas, in a thermal spa utilizing the waters from Guarani (Botucatu-Piramboia) aquifer. The results reported here provide additional information relative to that of previous studies focusing on the presence of radionuclides in the aquifer, which have mainly characterized those belonging to uranium and thorium series decay, such as the uranium isotopes (U-238 and U-234), radium isotopes (Ra-226 and Ra-228), radon daughters (Bi-214 and Pb-214) and radon (Rn-222) itself the results obtained were compared with the maximum permissible concentration limits in air and drinking water defined by international standards, such as the guidelines for drinking water quality established by the World Health Organization. The possible processes responsible for the presence of radon in the aquifer were also considered in order to evaluate the data obtained.

An implicit BEM formulation to model strong discontinuities in solids

A boundary element method (BEM) formulation to predict the behavior of solids exhibiting displacement (strong) discontinuity is presented. In this formulation, the effects of the displacement jump of a discontinuity interface embedded in an internal cell are reproduced by an equivalent strain field over the cell. To compute the stresses, this equivalent strain field is assumed as the inelastic part of the total strain. As a consequence, the non-linear BEM integral equations that result from the proposed approach are similar to those of the implicit BEM based on initial strains. Since discontinuity interfaces can be introduced inside the cell independently on the cell boundaries, the proposed BEM formulation, combined with a tracking scheme to trace the discontinuity path during the analysis, allows for arbitrary discontinuity propagation using a fixed mesh. A simple technique to track the crack path is outlined. This technique is based on the construction of a polygonal line formed by segments inside the cells, in which the assumed failure criterion is reached. Two experimental concrete fracture tests were analyzed to assess the performance of the proposed formulation.

Linear analysis of building floor structures by a BEM formulation based on Reissner's theory

In this work, the plate bending formulation of the boundary element method (BEM) based on the Reissner's hypothesis is extended to the analysis of zoned plates in order to model a building floor structure. In the proposed formulation each sub-region defines a beam or a slab and depending on the way the sub-regions are represented, one can have two different types of analysis. In the simple bending problem all sub-regions are defined by their middle surface. on the other hand, for the coupled stretching-bending problem all sub-regions are referred to a chosen reference surface, therefore eccentricity effects are taken into account. Equilibrium and compatibility conditions are automatically imposed by the integral equations, which treat this composed structure as a single body. The bending and stretching values defined on the interfaces are approximated along the beam width, reducing therefore the number of degrees of freedom. Then, in the proposed model the set of equations is written in terms of the problem values on the beam axis and on the external boundary without beams. Finally some numerical examples are presented to show the accuracy of the proposed model.

Environmental education and the health risk question: how do we educate the educators working with this theme?

Our society is presently seeing a trend of continuous increase of risk with severe consequences, especially those linked to environmental aspects. It has obligated us to reflect on this production and its effects, either positive or negative, and, after a long reflection, to think about the adopted model of civilization and the possibilities of changing such a model. The educational institution is among the social departments responsible for this revision process, since it represents one possibility to promote a more critical vision from society, providing it with tools needed for a more responsible action. However, schools are dominated by a traditional work, which does not allow for enough and proper attention to these relevant and current questions, and which involve a critical analysis of the conceptions and values established by our civilization, resulting in the present patterns of science-technology-society relations and their influence on the environment and health. Several research works have indicated a diversity of barriers that obstruct this necessary change. Since formal education plays an important role in the education of society for this theme, in this paper the possibilities and difficulty dealing with this problem are discussed, focusing on the question of teacher education, based on investigations related to teacher education programs for environmental education. The data collected show the urgency for introducing this theme in teacher training programs, taking into account the fact that educators have their own conceptions, values and attitudes that should be considered in these programs.

Aircraft accident in Brazil: Boeing vs. Legacy?

Air accidents represent a small proportion of the flights registered worldwide. Airplane collisions in the air are rare. In September of 2006, a Boeing 737-800 collided in midair with a Legacy Jet. It was the largest accident registered in the history of Brazilian aviation until that time. The present study explores aspects of press coverage of the accident. Data and information reported in the media about the accident from September 2006 to August 2007 were collected and discussed. Media coverage called attention to two unusual aspects: politicisation of the discussion, culminating in the opening of congressional inquiries, and equally the concomitance of police investigations interfering in the work of agencies responsible for the official accident investigation. Emphasis on assigning guilt and establishing penalties may close the windows of opportunity an accident had opened for discussions on the improvement of air safety. In Brazil, political imperatives and organizational pressures have interfered and the possibilities of organizational learning from the accident have been drastically curtailed.

A BEM formulation based on Reissner's theory to perform simple bending analysis of plates reinforced by rectangular beams

In this work, the plate bending formulation of the boundary element method (BEM), based on the Reissner's hypothesis, is extended to the analysis of plates reinforced by rectangular beams. This composed structure is modelled by a zoned plate, being the beams represented by narrow sub-regions with larger thickness. The integral equations are derived by applying the weighted residual method to each sub-region, and summing them to get the equation for the whole plate. Equilibrium and compatibility conditions are automatically imposed by the integral equations, which treat this composed structure as a single body. In order to decrease the number of degrees of freedom, some approximations are considered for both displacements and tractions along the beam width. The accuracy of the proposed model is illustrated by simple examples whose exact solution are known as well as by more complex examples whose numerical results are compared with a well-known finite element code.

Wavelet-Galerkin method for one-dimensional elastoplasticity and damage problems: Constitutive modeling and computational aspects

This work presents an analysis of the wavelet-Galerkin method for one-dimensional elastoplastic-damage problems. Time-stepping algorithm for non-linear dynamics is presented. Numerical treatment of the constitutive models is developed by the use of return-mapping algorithm. For spacial discretization we can use wavelet-Galerkin method instead of standard finite element method. This approach allows to locate singularities. The discrete formulation developed can be applied to the simulation of one-dimensional problems for elastic-plastic-damage models. (C) 2007 Elsevier B.V. All rights reserved.

Computational tool to support design of DAC Converter model AD7528 with the object code in XML

Based on literature review, electronic systems design employ largely top-down methodology. The top-down methodology is vital for success in the synthesis and implementation of electronic systems. In this context, this paper presents a new computational tool, named BD2XML, to support electronic systems design. From a block diagram system of mixed-signal is generated object code in XML markup language. XML language is interesting because it has great flexibility and readability. The BD2XML was developed with object-oriented paradigm. It was used the AD7528 converter modeled in MATLAB / Simulink as a case study. The MATLAB / Simulink was chosen as a target due to its wide dissemination in academia and industry. From this case study it is possible to demonstrate the functionality of the BD2XML and make it a reflection on the design challenges. Therefore, an automatic tool for electronic systems design reduces the time and costs of the design.

Celestial mechanics: from the errant stars to guidance of spacecrafts

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Computational analysis and physico-chemical characterization of an inclusion compound between praziquantel and methyl-beta-cyclodextrin for use as an alternative in the treatment of schistosomiasis

Schistosomiasis is still an endemic disease in many regions, with 250 million people infected with Schistosoma and about 500,000 deaths per year. Praziquantel (PZQ) is the drug of choice for schistosomiasis treatment, however it is classified as Class II in the Biopharmaceutics Classification System, as its low solubility hinders its performance in biological systems. The use of cyclodextrins is a useful tool to increase the solubility and bioavailability of drugs. The aim of this work was to prepare an inclusion compound of PZQ and methyl-beta-cyclodextrin (MeCD), perform its physico-chemical characterization, and explore its in vitro cytotoxicity. SEM showed a change of the morphological characteristics of PZQ:MeCD crystals, and IR data supported this finding, with changes after interaction with MeCD including effects on the C-H of the aromatic ring, observed at 758 cm(-1). Differential scanning calorimetry measurements revealed that complexation occurred in a 1:1 molar ratio, as evidenced by the lack of a PZQ transition temperature after inclusion into the MeCD cavity. In solution, the PZQ UV spectrum profile in the presence of MeCD was comparable to the PZQ spectrum in a hydrophobic solvent. Phase solubility diagrams showed that there was a 5.5-fold increase in PZQ solubility, and were indicative of a type A(L) isotherm, that was used to determine an association constant (K(a)) of 140.8 M(-1). No cytotoxicity of the PZQ:MeCD inclusion compound was observed in tests using 3T3 cells. The results suggest that the association of PZQ with MeCD could be a good alternative for the treatment of schistosomiasis.

Effects of Tityus serrulatus scorpion venom on lung mechanics and inflammation in mice

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Two-dimensional modeling of material failure in reinforced concrete by means of a continuum strong discontinuity approach

The paper presents a new methodology to model material failure, in two-dimensional reinforced concrete members, using the Continuum Strong Discontinuity Approach (CSDA). The mixture theory is used as the methodological approach to model reinforced concrete as a composite material, constituted by a plain concrete matrix reinforced with two embedded orthogonal long fiber bundles (rebars). Matrix failure is modeled on the basis of a continuum damage model, equipped with strain softening, whereas the rebars effects are modeled by means of phenomenological constitutive models devised to reproduce the axial non-linear behavior, as well as the bondslip and dowel effects. The proposed methodology extends the fundamental ingredients of the standard Strong Discontinuity Approach, and the embedded discontinuity finite element formulations, in homogeneous materials, to matrix/fiber composite materials, as reinforced concrete. The specific aspects of the material failure modeling for those composites are also addressed. A number of available experimental tests are reproduced in order to illustrate the feasibility of the proposed methodology. (c) 2007 Elsevier B.V. All rights reserved.