A theoretical and experimental analysis of cold-formed steel shapes subjected to bending - Channel and simple lipped channel

Cold-formed steel shapes have been widely employed in steel construction, where they frequently offer a lower cost solution than do traditional laminated shapes. A classic application of cold-formed steel shapes is purlins in the roof panel of industrial buildings, connected to the roof panel by means of screws. The combined effect of these two elements has been the subject of investigations in some countries. Design criteria were included in the AISI Code in 1991 and 1996. This paper presents and discusses the results obtained from bending tests carried out on shapes commonly used in Brazil, i.e., the channel and the simple lipped channel, Tests were carried out on double shapes with 4.5 and 6.0 meter spans, which were subjected to concentrated loads and braced against each other on the supports and at intermediary points in three different load situations. The panel shape was also analyzed experimentally, simulating the action of wind by means of a vacuum box designed specifically for this purpose. The test results were then compared to those obtained through the theoretical analysis, enabling us to extract important information upon which to base proposed design criteria for the new Brazilian code.

Distortional buckling of simple lipped channel in bending results of the experimental analysis versus direct strength methods

Cold-formed steel members are subject to failure caused by buckling, normally under loads smaller than those corresponding to partial or total yielding of the cross section. The buckling of members in bending can be classified as local or global, and the occurrence of one or the other type is expected by the members' geometric characteristics and by the constraints and load conditions. One of the local instability modes that can characterize a member's failure is distortional buckling of the cross section occurring on its own plane and involving lateral displacements and rotations. This paper presents and discusses the procedures and results obtained from experimental tests of cold-formed steel members under bending. Forty-eight beams were carried out on members in simple lipped channel, in pairs, with 6-meter spans and loads applied by concentrated forces at every 1/3 of the span. The thickness, width and dimensions, of the stiffeners were chosen so that the instability by distortion buckling of the cross section was the principal failure mode expected. The experimental results are compared with the obtained results by using the direct strength method.

Verificação de pilares metálicos compostos constituídos por perfis formados a frio por meio de programa computacional

In this work, we discuss the procedures adopted for the design of built-up columns (laced and battened columns). Built-up columns are widely used in steel construction generally when the compression forces are relatively low and the column buckling lengths are large. They are commonly used in industrial buildings, for example, as posts for cladding, or as columns supporting a crane girder. Unlike columns with full section, in the case of built-up columns, it is necessary to evaluate the shear stiffness. In fact, the shear strength leads to a significant reduction of the critical load. In the context of this work, the components of the columns (chords, diagonals, posts, etc.) are formed by cold-formed members. In order to systematize and rationalize the verification of the built-up columns, this work aim to develop a computer program based on the standards NBR 14762, NBR 6355 and Eurocode 3, basically the considerations of the part EN 1993-1-1

Cryptic lineages and Pleistocene population expansion in a Brazilian Cerrado frog

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Características de carcaça e composição corporal de touros jovens da raça Nelore terminados em diferentes sistemas

O objetivo do trabalho foi avaliar comparativamente as características de carcaça e a composição corporal de machos jovens da raça Nelore não-castrados, filhos de touros com diferencial positivo (Linhagem Seleção) ou nulo (Linhagem Controle) para ganho de peso aos 378 dias de idade. Utilizaram-se informações de 92 zebuínos Nelore, com peso de abate médio de 456,00 kg, sendo 51 animais pertencentes à Linhagem Seleção e 41 animais da Linhagem Controle, foram criados em pastagens cultivadas até os 18 meses, quando foram alocados nos dois sistemas de terminação, de forma a compor grupos homogêneos quanto ao peso e filiação. Os animais de confinamento receberam, em baias individuais, ração para possibilitar ganhos de 1,0 kg/cab/dia. Antes do abate, os animais foram submetidos a jejum e pesados, quando se obteve o peso de abate. Após o armazenamento das carcaças em câmara fria, obteve-se a seção da 9ª-10ª-11ª costelas. Não houve efeito significativo de linhagem para nenhuma das características analisadas, exceto para a porcentagem de ossos, sendo que os animais da Linhagem Seleção superaram os animais da Linhagem Controle. O regime de terminação apresentou efeito significativo para a quase totalidade das características estudadas, com exceção para as características de composição corporal. Não houve efeito significativo de interação entre linhagem e terminação. As classes de idade apresentaram efeito significativo para as características peso de abate, peso de carcaça quente, peso da gordura renal-pélvica-ingüinal, porcentagem de músculo, gordura e osso.

Ligações em estruturas metálicas com ênfase em perfís formados a frio

Pós-graduação em Engenharia Civil - FEIS

Estudo da estabilidade e da capacidade resistente de painéis estruturais do sistema construtivo Light Steel Framing

Pós-graduação em Engenharia Civil - FEIS

Determinação teórico-experimental da rigidez ao cisalhamento devido à restrição das telhas conectadas nas terças

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização de extratos vegetais em proteção de plantas

Usage of pesticies in excessive doses or in an inadequate way to control diseases, pests and weeds, has promoted significant environmental damage, contamination of animals, intoxication of farmers, among others. These factors lead to occur the resistance of weeds, pests and pathogens, the appearance of iatrogenic diseases, biological imbalance and reduction in biodiversity. Seeking less aggressive alternatives, plant extracts have been used successfully. Compared to synthetic products, they offer great advantages as generating new compounds, which pathogens are unable to inactivate, and are less toxic, of rapid degradation in the environment, they have broad modes of action, and are derived from renewable resources. It should be emphasized that there are some limitations on its use. The extracts have potencial as insecticide, fungicide, herbicide and nematicide and are considered of good efficiency. The methodologies for obtaining can be achieved through cold extraction, open and closed hot system. The use of plant extracts reappears as a promising and unique option for integrated management in plant protection, being considered as an alternative to control plant pathogens, demonstrating excellent results without causing harm to the environment and living beings.

Electrochemical behavior of cobalt oxide coatings on cold-rolled steel in alkaline sodium sulfate

The electrochemical behavior of a coating of cobalt oxide on cold-rolled steel in alkaline sodium sulfate was Studied using the electrochemical techniques of open-circuit potential measurements and electrochemical impedance spectroscopy. The coating was prepared at different annealing temperatures ranging from 350 to 750 degreesC and characterized by SEM, EDX and XRD. Below 550 degreesC the composition of the coating was basically of Co3O4. At 750 degreesC CoO was formed and big cracks appeared on the film exposing an inner layer of iron oxides. Analysis of the EIS data is very difficult because of the complexity of the interface structure. It can be inferred that the charge transfer resistance of the coatings prepared at 350 and 450 C were higher than those for the coatings prepared at temperatures above 550 degreesC. (C) 2002 Published by Elsevier B.V. Ltd.

Preliminary X-ray crystallographic studies of a tetrameric phospholipase A(2) formed by two isoforms of crotoxin B from Crotalus durissus terrificus venom

Crotoxin B is a basic phospholipase A(2) found in the venom of Crotalus durissus terrificus and is one of the subunits that constitute crotoxin. This heterodimeric toxin, which is the main component of C. d. terrificus venom, is completed by an acidic, nontoxic and non-enzymatic component (crotoxin A) and is involved in important envenomation effects, such as neurological disorders, myotoxicity and renal failure. Although crotoxin was first crystallized in 1938, no crystal structure is currently available for crotoxin, crotoxin A or crotoxin B. In this work, the crystallization, X-ray diffraction data collection to 2.28 angstrom resolution and molecular-replacement solution of a novel tetrameric complex formed by two dimers of crotoxin B isoforms (CB1 and CB2) is presented.

THE SECTION SIRODOTIA OF BATRACHOSPERMUM (RHODOPHYTA, BATRACHOSPERMACEAE) IN BRAZIL

The taxonomy, distribution and ecology of Section Sirodotia of Batrachospermum in Brazil is studied. Only one species, B. delicatulum (SKUJA) NECCHI & ENTWISLE, was recognized. This species presents a wide range of morphological features, occurs in a number of distinct habitats and environmental conditions and is widely distributed in Brazil. A full account of the species taxonomy is given and the synonyMy of B. ateleium comb. nov. SKUJA is confirmed. Two growth forms (dense and open) were found in the Brazilian specimens, but they were not treated as different taxa because a continuous range was observed between them. Two morphological features were proposed for species delineation: early development of gonimoblast and presence of specialized spermatangial branches. Three distinct groups of Sirodotia species can be recognized on the basis of these criterions: B. delicatulum (gonimoblast initial arises from a semiglobular protuberance of the carpogonium), B. suecicalum KYLIN (gonimoblast initial arises from the non-protuberant side of the carpogonium) and B. segawae KUMANO and B. yutakae KUMANO (with specialized spermatangial branches).

Morphological analysis of pits formed on Al 2024-T3 in chloride aqueous solution

It has been used a new image analysis method, based on segmentation by shape parameters, for pits morphology examination from Al 2024 aluminum-copper alloy in chloride aqueous solution. Corrosion behavior of this alloys in naturally aerated 3.5% NaCl solution has been investigated through open circuit potential measurements. Afterwards, pits have been characterized by image analysis taking density and size measurements right from corroded surfaces. Morphological investigation has been conducted for profiles, cut orthogonally from mean surface planes, and observed through light microscopy. Image analysis data could demonstrate that pits are wider than deep, evoluting for conical, quasi-conical or irregular shapes. Most pits have presented a quasi-conical morphology, but the wider ones have evoluted to an irregular shape influenced by sub-surface microstructure. Image analysis based on shape segmentation could enhance the differences on morphological behavior. (C) 2004 Elsevier B.V. All rights reserved.

Leaf anatomical and molecular studies in Bulbophyllum section Micranthae (Orchidaceae) and their implications for systematics

Bulbophyllum section Micranthae comprises 12 species of rupicolous or epiphytic orchids occurring in forests or in open rocky fields in Cerrado/Atlantic Forest ecotones throughout South America. We examined the leaf anatomy of 14 species and compared them with molecular data (nrITS) in phylogenetic analyses. The leaves of Bulbophyllum section Micranthae are characterised by uniseriate epidermis, with periclinal external cell wall thicker than the internal, presence of epicuticular wax, stomata present only on the abaxial surface with suprastomatic chambers, and collateral vascular bundles associated with sclerenchyma fibres. Some of these characters are shared with other rupicolous Orchidaceae species, demonstrating adaptive convergence in xeromorphic habitats. We found some anatomical characteristics with phylogenetic value. Bulbophyllum section Micranthae can be separated into two lineages: those with needle-like leaves, or flat leaves. The analyses show that anatomical characters as well as molecular data may contribute to the development of phylogenetic hypotheses. © 2013 Botanical Society of Sao Paulo.

Sequential healing of open extraction sockets. An experimental study in monkeys

AimTo describe the sequential healing of open extraction sockets at which no attempts to obtain a primary closure of the coronal access to the alveolus have been made.Material and methodsThe third mandibular premolar was extracted bilaterally in 12 monkeys, and no sutures were applied to close the wound. The healing after 4, 10, 20, 30, 90 and 180days was morphometrically studied.ResultsAfter 4days of healing, a blood clot mainly occupied the extraction sockets, with the presence of an inflammatory cells' infiltrate. A void was confined in the central zones of the coronal and middle regions, in continuity with the entrance of the alveoli. At 10days, the alveolus was occupied by a provisional matrix, with new bone formation lining the socket bony walls. At 20days, the amount of woven bone was sensibly increasing. At 30days, the alveolar socket was mainly occupied by mineralized immature bone at different stages of healing. At 90 and 180days, the amount of mineralized bone decreased and substituted by trabecular bone and bone marrow. Bundle bone decreased from 95.5% at 4days to 7.6% at 180days, of the whole length of the inner alveolar surface.ConclusionsModeling processes start from the lateral and apical walls of the alveolus, leading to the closure of the socket with newly formed bone within a month from extraction. Remodeling processes will follow the previous stages, resulting in trabecular and bone marrow formation and in a corticalization of the socket access.