Influência da altura das garras dos pneus de um trator em área de plantio direto

This work was carried out to evaluate the performance of a farm tractor fitted with two sets of tires with high lugs and another set of tires with tallow lugs in straw without tillage (corn straw). The travel speeds used were approximately 4, 5, 6 and 7 km h(-1) and a constant pulling force of 25 kN was fixed. Tractor traction, forward speed, slip and consumption of fuel were measured and drawbar power, the ratio between the consumption and power and traction coefficient were calculated. It was observed that the tractor performance was similar to high and low lug tire conditions, in an area covered with corn straw.

Desempenho de trator agrícola em três superfícies de solo e quatro velocidades de deslocamento

The aim of this work was to evaluate tractor performance in soil with three different surfaces: firm soil without covering, mobilized soil, and firm soil with vegetal residue of corn and braquiaria, for four forward speeds. The experiment was accomplished in three plots determined by the soil conditions. In each plot four treatments were composed by the forward speed obtained by the changes of the tractor gear. Six repetitions were used in each plot, totaling 72 experimental units, combination of the traction, slip of the rear and front wheels, forward speed and fuel consumption. The values of the tractor performance obtained led to the conclusion that in the firm soil without vegetable covering the tractor performance was better, followed by the soil with the firm surface and covered with corn straw and braquiaria and finally the mobilized soil. The best tractor performance was obtained in the C1 gear that supplied the forward speed of 6 km h(-1).

Avaliação do ruído e da vibração no posto de trabalho em dois tratores agrícolas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento e avaliação de equipamentos e metodologia para determinação de parâmetros físicos do solo relacionados a dias trabalháveis com máquinas agrícolas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Limitações humanas do operador de máquinas agrícolas e o ambiente socio-laboral na sojicultura

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Avaliação dos níveis de vibração no operador de um trator agrícola ensaiado em pista normatizada em diferentes velocidades de deslocamento

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Soil compaction by machine traffic and least limiting water range related to soybean yield

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Seeder-fertilizer machine: energetic demand as a function of vegetal covering handling and manure deposition shank depth in no-tillage system

O trabalho teve por objetivo avaliar a demanda energética de uma semeadora-adubadora, em função do tipo e manejo da cultura de cobertura vegetal e da profundidade da haste de deposição de adubo. Foi utilizado um trator Valtra BM100, instrumentado, para tracionar uma semeadora-adubadora de precisão equipada com quatro fileiras de semeadura espaçadas de 0,9 m para cultura de milho. O experimento foi conduzido em parcelas subsubdivididas, na área experimental do Laboratório de Máquinas e Mecanização Agrícola (LAMMA) da UNESP-Jaboticabal, utilizando duas culturas de cobertura (mucuna-preta e crotalária), três manejos dessas coberturas, sendo dois mecânicos (triturador de palhas e rolo-faca) e um químico (pulverização com herbicida), realizados 120 dias após a semeadura das culturas de cobertura e três profundidades da haste de deposição do adubo (0,11; 0,14 e 0,17 m), perfazendo 18 tratamentos, com quatro repetições, totalizando 72 observações. Foram avaliados os parâmetros velocidade de deslocamento, patinagem, força na barra de tração, força de pico, potência na barra de tração, potência de pico e consumo de combustível. Pôde-se concluir que a força na barra de tração foi menor para as profundidades de 0,11 e 0,14 m da haste sulcadora de adubo, o mesmo ocorrendo para força de pico, potência na barra de tração e consumo volumétrico. O consumo específico foi menor na profundidade de 0,17 m da haste sulcadora de adubo. As culturas de cobertura e seus manejos não interferiram no desempenho das máquinas estudadas.

Networked control system for the guidance of a four-wheel steering agricultural robotic platform

A current trend in the agricultural area is the development of mobile robots and autonomous vehicles for precision agriculture (PA). One of the major challenges in the design of these robots is the development of the electronic architecture for the control of the devices. In a joint project among research institutions and a private company in Brazil a multifunctional robotic platform for information acquisition in PA is being designed. This platform has as main characteristics four-wheel propulsion and independent steering, adjustable width, span of 1,80m in height, diesel engine, hydraulic system, and a CAN-based networked control system (NCS). This paper presents a NCS solution for the platform guidance by the four-wheel hydraulic steering distributed control. The control strategy, centered on the robot manipulators control theory, is based on the difference between the desired and actual position and considering the angular speed of the wheels. The results demonstrate that the NCS was simple and efficient, providing suitable steering performance for the platform guidance. Even though the simplicity of the NCS solution developed, it also overcame some verified control challenges in the robot guidance system design such as the hydraulic system delay, nonlinearities in the steering actuators, and inertia in the steering system due the friction of different terrains. Copyright © 2012 Eduardo Pacincia Godoy et al.

Vibration and tipping of agricultural machinery: A reality to be adjusted

The present study aimed to develop a methodology for the collection, transfer, storage and processing of vibration levels emitted in jobs occupied in agricultural machinery. The reason of this work is the study the vibration dose applied to operators of heavy vehicles and its relation to occupational health, linking the still high number of accidents involving farm machinery in relation to overturning (tipping). There is a need for the development and improvement of efficient tools in measuring vibration and tilt machine work, which minimize damage to health and accident risks for operators.

Prediction of soil shear strength in agricultural and natural environments of the Brazilian Cerrado

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)