Hybrid layer thickness and resin tag length of a self-etching adhesive bonded to sound dentin

Objectives: the purpose of this study is to employ optical microscopy to measure the thickness of the hybrid layer and the penetration (tags) of an aggressive self-etching adhesive system into sound dentin.Methods: occtusat cavities were prepared in 40 extracted human posterior teeth. The prepared teeth were randomly assigned to four experimental groups with 10 specimens each. The self-etching adhesive system Adper Prompt L-Pop was applied to the dentin surface as follows: Group 1: cavosurface enamel was etched for 60 s and dentin for 20 s with 35% phosphoric acid get, immediately followed by application of the self -etching adhesive with a brush to the entire cavity for 15 s; Groups 2, 3, and 4: no pre-etching was performed, and the self -etching adhesive was applied to both enamel and dentin for 15, 30 and 45 s, respectively. After curing, the cavities were fitted with composite resin Fittek Z250. Afterwards, the teeth were decalcified and the restorations were carefully removed for later embedding in paraffin. The specimens were serially sectioned at 6 mu m of thickness and sequentially mounted in glass slides. These sections were stained with Brown and Brenn staining for posterior analysis and measurement of the hybrid layer and resin tags on a tight microscope with a micrometric ocular 40/075. The results were submitted to analysis of variance at the 5% level.Results: whenever there was significance, the Tukey test was applied at the 5% level. The specimens receiving application of acid etching before the selfetching. adhesive displayed a larger thickness of the hybrid layer; on the other hand, specimens receiving only application of the self -etching adhesive on dentin for 15, 30 and 45 s exhibited similar thickness of the hybrid layer. As regards the resin tags, no statistically significant differences could be found between the study groups.Conclusions: it could be concluded that the increase in the time of application of the self-etching adhesive Adper Prompt L-Pop did not significantly influence the formation and thickness of hybrid layer, as well as its penetration into the sound dentin surface. (c) 2005 Elsevier Ltd. All rights reserved.

Correlation of the hybrid layer thickness and resin tags length with the bond strength of a self-etching adhesive system.

The objective of this study was to measure the thickness of the hybrid layer (HLT), length of resin tags (RTL) and bond strength (BS) in the same teeth, using a self-etching adhesive system Adper Prompt L Pop to intact dentin and to analyze the correlation between HLTand RTL and their BS. Ten human molars were used for the restorative procedures and each restored tooth was sectioned in mesio-distal direction. One section was submitted to light microscopy analysis of HLT and RTL (400x). Another section was prepared and submitted to the microtensile bond test (0.5 mm/min). The fractured surfaces were analyzed using scanning electron microscopy to determine the failure pattern. Correlation between HLT and RTL with the BS data was analyzed by linear regression. The mean values of HLT, RTL and BS were 3.36 microm, 12.97 microm and 14.10 MPa, respectively. No significant relationship between BS and HLT (R2= 0.011, p>0.05) and between BS and RTL (R2= 0.038) was observed. The results suggested that there was no significant correlation between the HLT and RTL with the BS of the self-etching adhesive to dentin.

Analysis of hybrid layer thickness, resin tag length and their correlation with microtensile bond strength using a total etch adhesive to intact dentin.

The objective of this study was to evaluate the use of a two-step total etch and rinse adhesive, the correlation between the hyybrid layer thickness (HL) and bond strength (BS), and between resin tag length (RT) and bond strength in the same teeth, and also to evaluate the fracture patterns of the tested specimens. Ten human molars were used for the restorative procedure and then sectioned in two halves (mesio-distally). The materials used were Adper Single Bond 2, 3M ESPE, Ultra etch gel, Ultradent and Filtek Z250, 3M ESPE. One half were utilized to measure the HL thickness and RT length through light microscopy analysis (400x), and the other half was subject to a microtensile test to measure the BS. The fractured surfaces were analyzed by scanning electron microscopy and fracture patterns classified. The Pearson correlation test was applied (p = 0.05). The results of the analyses of each specimen then were correlated: mean HL thickness = 4.39 (0.48) microm, mean length of RT = 9.94 (1.69) microm, mean BS = 23.98 (10.24) MPa. A statistically significant correlation between HL thickness and bond strength was found (r = 0.93). The two step etch and rinse adhesive system, showed a strong correlation between HL thickness and bond strength. The most common fractures were adhesive, followed by cohesive in resin.

Influence of the hybrid layer thickness and resin tag length on microtensile bond strength.

The purpose of this study was to evaluate the correlation between the hybrid layer thickness/resin tag length and the microtensile bond strength of conventional two-step adhesive system, when applied to healthy dentinal tissue. After performing the restorative adhesive procedures and tooth extractions, ten specimens were sectioned in the mesiodistal direction. One section was used for microscopic analysis of the resin tag lengths and the hybrid layer thickness, while the other was used for the microtensile bond strength test (0.5 mm/min). The fractured surface was classified according to the fracture pattern, under a stereoscopic microscope at 40x magnification. Data obtained were submitted to analysis using one-way ANOVA and Pearson's Correlation test (alpha=0.05). The means corresponding to the hybrid layer thickness, resin tag lengths and the microtensile test were 2.68 microm, 6.43 microm and 16.23 MPa, respectively. There was no correlation between the means of the values obtained for the microtensile test, and those presented by the hybrid layer (r2=0.40, p>0.05) and resin tags (r2=0.21, p>0.05). The microtensile bond strength of the conventional two-step adhesive system Adper Single Bond 2 did not depend on the thickness of the hybrid layer and length of resin tags.

Correlation between hybrid layer thickness, resin tag length and microtensile bond strength of a self-etching adhesive system

The purpose of this study was to evaluate the correlation between the hybrid layer thickness, resin tag length and resin bond strength of a self-etching adhesive system to sound dentin tissue in vivo. After performing restorative procedures and tooth extractions, ten specimens were sectioned in a mesiodistal direction. One dental section was used for light microscope analysis, in which both the resin tag length and hybrid layer thickness were measured, while the other section was analyzed using a microtensile test (0.5 mm/min). The fractured surface of the latter section was characterized using a stereoscopic magnifying glass (40x magnifcation). The results were subject to statistical analysis using the Pearson Correlation Test (a = 0.05). The hybrid layer thickness, resin tag length and resin bond strength mean values were 2.19 microm (0.34), 4.34 microm (0.28) and 9.73 MPa (5,55), respectively. In addition, correlation tests between the resin tag length and the resin bond strength (r=0.014) and also between the hybrid layer thickness and bond strength (r=0.43), showed no statistically significant correlation. The microtensile bond strength of Adper Prompt L Pop self-etching adhesive system does not depend on hybrid layer thickness or resin tag length.

Características anatômicas da lâmina foliar e do colmo de gramíneas forrageiras tropicais, em função do nível de inserção no perfilho, da idade e da estação de crescimento

Foram avaliados os efeitos da idade, do nível de inserção da folha no perfilho e da estação de crescimento (verão ou outono), sobre a proporção de tecidos e a espessura da parede celular em lâminas foliares e segmentos de colmo de capim-braquiária (Brachiaria decumbens), capim-gordura (Melinis minutiflora) e capim-tifton 85 (Cynodon sp). Lâminas foliares das posições inferior e superior do perfilho foram colhidas no dia da exposição da lígula e 20 dias após. Foram determinadas as proporções relativas de epiderme, xilema, floema, bainha parenquimática dos feixes, esclerênquima, parênquima no colmo e mesofilo na lâmina foliar. Foram medidas as espessuras das paredes dos vasos de metaxilema e do esclerênquima da lâmina e do colmo. A proporção de tecidos em lâminas foliares não foi alterada pela idade nem pela estação de crescimento, sendo a espessura da parede de células do esclerênquima da lâmina a única característica modificada pela idade. Lâminas do nível de inserção superior apresentaram mais elevadas proporções de esclerênquima, bainha parenquimática dos feixes e xilema e células do esclerênquima e do metaxilema com paredes mais espessas, enquanto as lâminas do nível de inserção inferior se destacaram por apresentar mais elevada proporção de mesofilo e paredes celulares mais delgadas. Enquanto a proporção de parênquima decresceu, a área relativa de esclerênquima e as espessuras das paredes celulares variaram diretamente com a idade do colmo e foram maiores, em geral, no verão.

Morfologia do útero de cutias nulíparas e não nulíparas

Descreveu-se a morfologia do útero de cutias nulíparas e não nulíparas por meio de ovariossalpingoisterectomia. A análise macroscópica do útero foi realizada in loco e na peça retirada. Segmentos das porções proximal, média e distal do órgão foram colhidas, fixadas e preparadas histologicamente, sendo as amostras analisadas à microscopia de luz, e realizada a histomorfometria das camadas uterinas. Topograficamente, o útero localiza-se na região sublombar, caudalmente aos rins, em continuação aos ovários e às tubas uterinas, estendendo-se até à entrada da pelve, onde se posiciona dorsalmente à bexiga. Caracteriza-se como do tipo duplo, embora culmine em apenas um óstio cervical externo. Microscopicamente, a mucosa uterina é formada por variações do epitélio, de cilíndrico a pseudoestratificado, que se apoia em tecido conjuntivo frouxo, onde se observam glândulas endometriais revestidas por epitélio cilíndrico, além da presença de vasos sanguíneos. A camada muscular subdivide-se em interna ou submucosa, média ou vascular e externa ou subserosa. A camada serosa é composta por tecido conjuntivo e mesotélio. Na histomorfometria, verificou-se que a espessura uterina total e a espessura da camada mucosa, em média, foram maiores nas fêmeas não nulíparas.

Avaliação Macroscópica e Morfométrica do Oviduto de Codornas (Coturnix coturnix japonica) Quando Alimentadas com Diferentes Níveis de Proteína

Foram utilizadas doze codornas domésticas, divididas em três grupos de quatro aves cada. As aves receberam rações padronizadas contendo 16%, 20% e 24% de proteína, sendo alimentadas por um período de quinze semanas, quando foram pesadas e sacrificadas imediatamente. Após a abertura da cavidade abdominal e evisceração do trato gastrointestinal, os ovários e ovidutos foram dissecados e pesados. Com o auxílio de um paquímetro mediu-se o comprimento das partes do oviduto: infundíbulo, magno, istmo, útero e vagina e avaliou-se o número de pregas do magno e do istmo. Foram realizados cortes histológicos do magno, istmo e útero onde se obteve medidas das espessuras das camadas epitelial e glandular. Os dados foram submetidos a análise de variância (ANOVA) e observou-se que não houve diferenças significativas no peso corporal, peso do ovário, do oviduto e nos comprimentos das partes do oviduto bem como no número de pregas do magno e ístmo. Verificou-se diferenças significavas na espessura da camada epitelial do istmo de aves alimentadas com 20% de proteína na ração. Além disso, houve diferenças significativas na espessura da camada glandular do magno, istmo e útero das aves alimentadas com 24% de proteína na ração em relação às aves que receberam 16% e 20% de proteína. O nível de 24% de proteína aumentou a espessura da camada glandular do magno, ístmo e útero o que poderia resultar em melhoria no peso dos ovos e na espessura da casca.

Ultrasonic density measurement cell design and simulation of non-ideal effects

This paper presents a theoretical analysis of a density measurement cell using an unidimensional model composed by acoustic and electroacoustic transmission lines in order to simulate non-ideal effects. The model is implemented using matrix operations, and is used to design the cell considering its geometry, materials used in sensor assembly, range of liquid sample properties and signal analysis techniques. The sensor performance in non-ideal conditions is studied, considering the thicknesses of adhesive and metallization layers, and the effect of residue of liquid sample which can impregnate on the sample chamber surfaces. These layers are taken into account in the model, and their effects are compensated to reduce the error on density measurement. The results show the contribution of residue layer thickness to density error and its behavior when two signal analysis methods are used. (c) 2006 Elsevier B.V. All rights reserved.

Histological and immunohistochemical study of the expression of p53 and ki-67 proteins in the mucosa of the tongue, pharynx and larynx of rats exposed to cigarette smoke

Introduction: Head and neck cancers are linked to smoking. The most affected sites are the oral cavity, pharynx and larynx. Experimental studies show epithelial lesions caused by cigarette smoke. Objectives: To investigate in rats the effects of acute cigarette smoke exposure on the mucosa of the tongue, pharynx and larynx.Material and method: Wistar rats were allocated into two groups of 20 animals: CG (control) receiving food and water ad libitum and TG (Tobacco) exposed to the smoke of 40 cigarettes/day for 60 days. Biopsy of their tongues, pharynxes and larynxes were subjected to histopathological, histomorphometric and immunohistochemical studies of protein p53 and ki-67.Result: The histological analysis of tongue from the Tobacco group revealed epithelial hyperplasia (90%), basal cell hyperplasia (95%) and mild to moderate dysplasia (85%). In pharynx showed basal cell hyperplasia (85%), dysplasia (25%) and vascular congestion (95%). In larynx showed basal cell hyperplasia (70%), epithelial hyperplasia (55%), congestion (100%) and inflammatory infiltrate (25%). Morphometric analysis revealed that keratin layer thickness was greater in the tobacco group. P53 immunoexpression was negative in both groups. Ki-67 immunoexpression was positive in basal cell nuclei but in parabasal cell nuclei it was positive only in the Tobacco group.Conclusions: The exposure of animals to cigarette smoke for 60 days resulted in benign lesions. The duration of exposure was not enough to cause the development cancer, as confirmed by the negative expression of p53 protein in all slides examined. Analysis of ki-67 expression showed intense epithelial proliferation in response to damage.

Phosphate distribution in the sediments along a cascade of reservoirs - (Paranapanema River, SE, Brazil)

Total phosphorus concentrations in the sediment of a cascade of 8 reservoirs located in the Paranapanema River (SE, Brazil) were analysed during two consecutive seasonal periods (2000 and 200 1). The reservoirs of Jurumirim, Chavantes, Salto Grande, Canoas 11, Canoas 1, Capivara, Taquarucu and Rosana were built during the last five decades with the purpose of hydroelectric generation. The sampling points were distributed along a 700 km of river stretch in 19 stations distributed in the river-reservoirs zones and main tributaries as well as in 5 stations representing the adjacent wetlands. The nutrient concentration was determined in samples from surface layers of sediment. Temporal and spatial changes were observed for both years. Three different areas could be identified along the river, considering not only Tot-P variations but also others physical and chemical characteristics such as organic matter concentration, nitrogen concentration of sediment and 02, pH, conductivity and Eh measured in the bottom layer of the water column. Higher values of Tot-P were found in the middle and lower region of the Paranapanema basin (maximum value of 1.96 mg g(-1) in Tibagi River in October/2001). Agricultural practices and cattle raising are the main external sources of nutrient in these regions. Superficial or sub-superficial watershed drainage and tributaries entrances are important nutrient contributors, leading to an increasing accumulation of nutrient in the sediment. This process seems to be especially important in the middle region of the Paranapanema Valley, were the values of Tot-P were higher comparing to the other areas.

Bond strengths, degree of conversion of the cement and molecular structure of the adhesive-dentine joint in fibre post restorations

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Dry matter production of shoots and root density of two cultivars of Lablab purpureus (L.) Sweet

This experiment was conducted in green house conditions to evaluate the DM accumulation in the shoots and in the roots of two cultivars of Lablab purpureus (L.) Sweet. A 2x3 factorial (two cultivars and three evaluation dates) was conducted according to a randomized complete block design with four replications, being the cultivars Highworth and Rongai evaluated at 42, 56, and 70 days after seedling emergence (DASE). The results indicated that the cvs. Highworth and Rongai have the same pattern of DM accumulation in the shoots. In the upper layer of the soil (0-0.20 in) it was found 38.83% and 43.64% of the DM accumulated in the roots down to 2.00 in depth, in the cvs. Highworth and Rongai, respectively. In the deepest layer (1.80-2.00 in) it was found 3.02% and 1.5% of the DM accumulated in the roots of the cvs. Highworth and Rongai, respectively. The root density showed a striking decrease upper layer from the soil (0-0.2 m) down to the depth of 0.60 0.80 in (from 10.83 to 1.75 cm.cm(-3) in the cv. Highworth and from 10.76 to 1.28 cm.cm(-3) in the cv. Rongai). At the bottom layer (1.80-2.00 in) the root density values were 0.98 cm.cm(-3) and 0.59 cm.cm(-3), respectively for the cvs. Highworth and Rongai. The root/shoot ratios were similar in both cvs. and decreased from 42 to 70 DASE showing that the cvs. evaluated had the same dynamics of DM accumulation.

Root growth and cotton nutrition as affected by liming and soil compaction

Soil columns were produced by filling PVC tubes with a Dark Red Latosol (Acrortox, 22% of clay). A compacted layer was established at the depth of 15 cm in the columns. In the compacted layer, soil was packed to 1.13, 1.32, 1.48, and 1.82 Mg kg(-1), resulting in cone resistances of 0.18, 0.43, 1.20, and 2.50 MPa. Cotton was cropped for 30 days. Lime was applied to raise base saturation to 40, 52, and 67%. The highest base saturation caused a decrease in phosphorus (P) and zinc (Zn) concentrations in the plants. A decrease in root dry matter, length and surface area was also observed. This could be a consequence of lime induced Zn deficiency. Root growth was decreased in the compacted layer, and complete inhibition was noticed at 2.50 MPa. Once the roots got through the compacted layer, there was a growth recovery in the bottom layer of the pots. The increase in base saturation up 52% was effective in preventing a decrease in cotton root length at soil resistances to 1.20 MPa. Where the roots were shorter, there was an increase in nutrient uptake per unit of root surface area, which kept the plants well nourished, except for P.