Produtividade fabril I: método para rápido aumento da produtividade fabril

O método para rápido aumento da produtividade fabril, aplicável principalmente à indústria brasileira de manufatura (17% do PIB), fundamenta-se exclusivamente na redução ou eliminação do tempo inativo do homem, da máquina e do material, que é a grande causa da ineficiência. O método exige a utilização de apenas cinco das mais simples, elementares e conhecidas técnicas e é aplicável às vinte situações mais freqüentes (objetos de estudo) na indústria de manufatura. Nossa experiência atesta que o método é capaz de aumentar a produtividade fabril em valor superior a 30%, em poucos meses e de forma perene (houve um caso de aumento de 160% em toda uma seção de usinagem de uma empresa multinacional). Sua aplicação e a implantação das medidas dele decorrentes são feitas com extrema facilidade e, por isto, os resultados surgem muito rapidamente. Atinge portanto seu objetivo: proporcionar aumento da produtividade fabril em curto espaço de tempo. Os demais artigos da série detalharão os objetos de estudo.

Influência da queima de cana-de-açúcar na presença de HPAs em ambiente residencial

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Spatial variability of soil penetration resistance influenced by season of sampling

O objetivo deste trabalho foi analizar a distribuição espacial da compactação do solo e a influência da umidade do solo na resistência à penetração. Esta última variável foi descrita pelo índice de cone. O solo estudado foi Nitossolo e os dados de índice de cone foram obtidos usando um penetrômetro. A resistência do solo foi avaliada a 5 profundidades diferentes, 0-10 cm, 10-20 cm, 20-30 cm, 30-40 cm e mais de 40 cm, porém o conteúdo de umidade do solo foi medido a 0-20 cm e 20-40 cm. As condições hídricas do solo variaram nas diferentes amostragems. Os coeficientes de variação para o índice de cone foram 16,5% a 45,8% e os do conteúdo de umidade do solo variaram entre 8,96% e 21,38%. Os resultados sugeriram elevada correlação entre a resistência do solo, estimada pelo índice de cone e a profundidade do solo. Sem embargo, a relação esperada com a umidade do solo não foi apreciada. Observou-se dependência espacial em 31 de 35 séries de dados de índice de cone e umidade do solo. Esta dependência foi ajustada por modelos exponenciais com efeito pepita variável de 0 a 90% o valor do patamar. em séries de dados o comportamento foi aleatório. Portanto, a técnica das distâncias inversas foi utilizada para cartografar a distribuição das variáveis que não tiveram estrutura espacial. Na krigagem constatou-se uma suavização dos mapas comparados com esses das distâncias inversas. A krigagem indicadora foi utilizada para cartografar a variabilidade espacial do índice de cone e recomendar melhor manejo do solo.

Determination of Population Size of Glass-like Carbon Sampling Used in Weibull Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Phylogenetic relationships within the speciose family Characidae (Teleostei: Ostariophysi: Characiformes) based on multilocus analysis and extensive ingroup sampling

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sampling mobility index: Case study in Assis - Brazil

The objective of this work is to present an index which may synthesize a set of indicators of mobility for medium size cities urban centers. Three great areas were selected to compose the mobility index: pedestrians, motor vehicles and cycling. The Sampling Mobility Index is given by the sum of the punctuation the indicators selected and can to result in 700 points, the best result to mobility, and 0 points, the worse to mobility. The result obtained is given by the Sampling Mobility Index equal to 390. This result indicates a critical situation in Assis, as far as mobility is concerned. (c) 2005 Elsevier Ltd. All rights reserved.

Methodology for load compensation in four-wire electrical power systems based on instantaneous sampling

This work describes a methodology for power factor control and correction of the unbalanced currents in four-wire electric circuits. The methodology is based on the insertion of two compensation networks, one wye-grounded neutral and other in delta, in parallel to the load. The mathematical development has been proposed in previous work [3]. In this paper, however, the determination of the compensation susceptances is based on the instantaneous values of load currents. The results are obtained using the MatLab-Simulink enviroment

Use of the internal standardization for difficult sampling by graphite furnace atomic absorption spectrometry

This work shows the potentiality of As as internal standard to compensate errors from sampling of sparkling drinking water samples in the determination of selenium by graphite furnace atomic absorption spectrometry. The mixture Pd(NO 3) 2/Mg(NO 3) 2 was used as chemical modifier. All samples and reference solutions were automatically spiked with 500 μg l -1 As and 0.2% (v/v) HNO 3 by the autosampler, eliminating the need for manual dilutions. For 10 μl dispensed sample into the graphite tube, a good correlation (r=0.9996) was obtained between the ratio of analyte absorbance by the internal standard absorbance and the analyte concentrations. The relative standard deviations (R.S.D.) of measurements varied from 0.05 to 2% and from 1.9 to 5% (n=12) with and without internal standardization, respectively. The limit of detection (LD) based on integrated absorbance was 3.0 μg l -1 Se. Recoveries in the 94-109% range for Se spiked samples were obtained. Internal standardization (IS) improved the repeatability of measurements and increased the lifetime of the graphite tube in ca. 15%. © 2004 Elsevier B.V. All rights reserved.

Determination of copper in fish feed by graphite furnace atomic absorption spectrometry using slurry sampling

The present work develops and optimizes a method to determine copper in samples of feces and fish feed by graphite furnace atomic absorption spectrometry (GFAAS) through the direct introduction of slurries of the samples into the spectrometer's graphite tube coated internally with metallic rhodium and tungsten carbide that acts as chemical modifiers. The limits of detection (LOD) and quantification (LOQ) calculated for 20 readings of the blank of the standard slurries (0.50% m/v of feces or feed devoid of copper) were 0.24 and 0.79 μg L -1 for the standard feces slurries and 0.26 and 0.87 μg L -1 for the standard feed slurries. The proposed method was applied in studies of absorption of copper in different fish feeds and their results proved compatible with that obtained from samples mineralized by acid digestion using microwave oven. © Springer Science+Business Media, LLC 2008.

SEQUENTIAL SAMPLING AND MICROSATELLITES FOR EVALUATION OF THE GENETIC QUALITY IN CORN SEEDS LOTS

In the seed production system, genetic purity is one of the fundamental requirements for its commercialization. The present work had the goal of determined the sample size for genetic purity evaluation, in order to protect the seed consumer and the producer and to evaluate the sensitivity of microsatellite technique for discriminating hybrids from their respective relatives and for detecting mixtures when they are present in small amounts in the samples. For the sequential sampling, hybrid seeds were marked and mixed in with the seed lots, simulating the following levels of contamination: 0.25, 0.5, 1.0, 2.0, 4.0, and 6.0%. After this, groups of 40 seeds were taken in sequence, up to a maximum of 400 seeds, with the objective of determining the quantity of seeds necessary to detect the percentage of mixture mentioned above. The sensitivity of microsatellite technique was evaluated by mixing different proportions of DNA from the hybrids with their respective seed lines. For the level of mixture was higher than 1:8 (1P1:8P2; 8P1:1P2), the sensitivity of the marker in detecting different proportions of the mixture varied according to the primer used. In terms of the sequential sampling, it was verified that in order to detect mixture levels higher than 1% within the seed lot- with a risk level for both the producer and the consumer of 0.05- the size of the necessary sample was smaller than the size needed for the fixed sample size. This also made it possible to reduce costs, making it possible to use microsatellites to certify the genetic purity of corn seeds lots.