Calorimetric study of the effect of water quantity on tetramethoxysilane hydrolysis under ultrasound stimulation

The ultrasound stimulated and oxalic acid-catalyzed hydrolysis of tetramethoxysilane (TMOS) was studied by means of a heat flux calorimetric method as a function of the initial water/TMOS molar ratio (r) ranging from 2 to 10. The method is based on the time recording of the hydrolysis exothermic heat peak. which takes place in acidulated heterogeneous water-TMOS mixtures under ultrasonic stimulation, accounting for the instantaneous hydrolysis rate. The hydrolysis rate increases from zero up to a maximum value during the heterogeneous step of the process and then diminishes naturally according to the reactant consumption. The total hydrolyzed quantity was found to be slightly increasing with r. The immiscibility gap of the TMOS- water system in the presence of the hydrolysis products has been inferred from the evaluation of the reacted quantity during the heterogeneous step of the reaction and it has been represented in a ternary diagram in the studied r-range.

Effects of the water quantity on the solventless TEOS hydrolysis under ultrasound stimulation

The acid hydrolysis under ultrasound stimulation of solventless tetraethoxysilane(TEOS)-water mixtures was studied at 40 degrees C, by means of a heat flux calorimetric method, as a function of the initial water/TEOS molar ratio (r) ranging from 2 to 10. The method is based on the time record of the exothermic heat peak of hydrolysis, arising after an induction time under ultrasound stimulation, which is a measure of the reaction rate. The hydrolysed quantity was found to be approximately independent of the water/TEOS molar ratio, even for r < 4. Polycondensation reaction takes place mainly for low water/TEOS molar ratio in order to supply water to allow almost complete hydrolysis. The overall process of dissolution and hydrolysis has reasonably been described by a previous modelling. The dissolution process of water in TEOS, under ultrasound stimulation and acid conditions, was found to be rather dependent of the alcohol produced in the hydrolysis reaction instead of the initial water quantity present in the mixture.

Formação de mudas de eucalipto com utilização de lixo orgânico e níveis de irrigação calculados por dois métodos

O estudo das características e das possibilidades de utilização de Resíduo Sólido Urbano (R.S.U.) e mais especificamente de Resíduo Sólido Orgânico Urbano (R.S.O.U.), no Brasil e no Mundo, ainda não produziu informações que possibilitem conhecimentos suficientes para tomadas de decisões que estão sendo exigidas, em razão do crescente volume de resíduos produzidos e os impactos ao meio ambiente. Este trabalho teve o objetivo de estudar o efeito da irrigação associada ao uso de R.S.O.U. para formação de mudas de eucalipto. A pesquisa foi desenvolvida na UNESP, Câmpus de Jaboticabal - SP, sendo adotado como delineamento estatístico o esquema fatorial inteiramente casualizado. Foram utilizados 11 substratos: dois tipos de solos (um Latossolo Vermelho eutrófico e um Latossolo Vermelho distrófico), com e sem adubação química, seis misturas de solo e R.S.O.U., e um utilizando somente R.S.O.U. Sementes de eucalipto var. Citriodora Hooker foram semeadas diretamente em topetes e irrigadas com base em dois métodos de quantificação da água evapotranspirada (tanque Classe A e determinação da massa), em quatro níveis (50; 70; 100 e 130% da evapotranspiração). Os dados coletados e analisados estatisticamente demonstraram que doses acima de 20% de R.S.O.U. na mistura, em solos destinados à produção de mudas de eucalipto, causam efeitos negativos na sobrevivência das plantas.

Isolado protéico de farinha de semente de goiaba (Psidium guajava): caracterização de propriedades funcionais e térmicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Características estruturais de géis de sílica preaparados a partir da sonohidrólise do tetraetilortosilicato com adições de álcool polivinílico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Propriedades estruturais de géis de sílica preparados a partir da sonohidrólise do tetraetilortosilicato com adições de dimetilformamida

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização de lodo de esgoto compostado e irrigação com água residuária em laranjeira valência

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Balanço hídrico na sub-bacia hidrográfica do Boi Branco – SP para gestão sustentável da agricultura irrigada

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Avaliação de genótipos de cártamo quanto ao desempenho agronômico, divergência genética e produtividade da água

Pós-graduação em Agronomia (Agricultura) - FCA

Utilization of Minimum Quantity Lubrication (MQL) with Water in CBN Grinding of Steel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A study on the viability of minimum quantity lubrication with water in grinding of ceramics using a hybrid-bonded diamond wheel

With the currently strict environmental law in present days, researchers and industries are seeking to reduce the amount of cutting fluid used in machining. Minimum quantity lubrication is a potential alternative to reduce environmental impacts and overall process costs. This technique can substantially reduce cutting fluids in grinding, as well as provide better performance in relation to conventional cutting fluid application (abundant fluid flow). The present work aims to test the viability of minimum quantity lubrication (with and without water) in grinding of advanced ceramics, when compared to conventional method (abundant fluid flow). Measured output variables were grinding power, surface roughness, roundness errors and wheel wear, as well as scanning electron micrographs. The results show that minimum quantity lubrication with water (1:1) was superior to conventional lubrication-cooling in terms of surface quality, also reducing wheel wear, when compared to the other methods tested.

CERAMIC MATERIAL FROM SEWAGE SLUDGE AS SUPPORT MATERIAL SUPPLY WATER FILTRATION

This study shows a possibility of using municipal sewage sludge after thermal treatment in the production of a filtering material to water treatment. Due to the fast urbanization and implementation of high standards for effluent in many countries in recent years, the sewage sludge is being produced in an ever increasing amount. Therefore, the use of sludge is a suitable solution for the expected large quantity of sludge. Dehydration of sludge was performed by controlled heating at temperatures of 1100 degrees C, 850 degrees C, 650 degrees C, 350 degrees C for 3 hours. After thermal treatment the sludge was characterized by X-ray fluorescence, TG/DTG/DTA, residue solubilization and residue lixiviation tests. The aim of the present work was to observe, thought the characterization techniques, if the treated sewage sludge is or not adequate to be used as filter material to water treatment. It will be verified which treatment temperature of the sludge offer possibility to its use in water treatment without carrying pollutants in concentrations out of the standards.

Structural features of silicas prepared in n-heptane/water/ethanol/sodium dodecylsulfate microemulsions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermal behavior of residues (sludge) originated from Araraquara water and sewage treatment station

The number of the cities with canalized water and sewage treatment stations has increased lately and consequently having in mind the great concern on environment preservation and the quality of the water used by society. However, these stations are nowadays causing another kind of problem: a huge quantity of sludge as residue. Due to the implication of the residue on the environment and, consequently, to human life quality, performing of an accurate investigation about the components of such sludge, as well as the thermal stability of this residue in the environment become necessary. This paper presents a study on sludge from water and sewage treatment station, as well as the thermal characterization of residue. Such study was performed through FTIR, atomic absorption, thermoanalytical (TG/DTG, DTA) techniques, that made it possible to observe that the main components of the sludge are clay, carbonates and organic substance, presenting a low rate of metals and a unique thermal behavior since the sludge from the treatment station has a higher thermal stability.

A dissolution and reaction modeling for hydrolysis of TEOS in heterogeneous TEOS-water-HCl mixtures under ultrasound stimulation

A simplified dissolution and reaction modeling was employed to study the hydrolysis of heterogeneous tetraethoxysilane (TEOS)-water-HCl mixtures under ultrasound stimulation. The nominal pH was changed from 0.8 to 2.0. The acid specific hydrolysis rate constant was determined as k = 6.1 mol(-1) 1 min(-1) [H+](-1) at 39 degreesC, in good agreement with the literature. Along the heterogeneous step of the reaction, the ultrasound maintains an additional quantity of water under a virtual state of dissolution besides the water dissolved due to the homogenizing effect of the alcohol produced in the reaction. The forced virtually dissolved water is probably represented by water at the TEOS-water interface during the heterogeneous step of the reaction. The mean radius of the heterogeneity represented by water dispersed in TEOS phase, while hydrolysis has not started yet, was evaluated as about 290 A. The HCl concentration accordingly increases the hydrolysis rate constant but its fundamental role on the immiscibility gap of the TEOS-water-ethanol system has not been unequivocally established. (C) 2002 Elsevier B.V. B.V. All rights reserved.