Modelos matemáticos aplicados a problemas na cultura da cana-de-açúcar e no aproveitamento da energia da biomassa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resposta varietal da cana-de-açúcar à deficiência hídrica, durante o desenvolvimento inicial em um latossolo vermelho distroférrico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modificação da fração lignocelulósica durante o processo de compostagem do bagaço de cana-de-açúcar

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Mudanças no uso da terra decorrentes da expansão da cultura da cana-de-açúcar na região oeste do estado de São Paulo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Biodegradação da vinhaça resíduo da produção de etanol

The State of São Paulo is responsible for the largest sugar cane production in Brazil, as well as the largest production of ethanol made of this raw material – which is widely used as fuel for automobiles. This utilization began in the 1970’s, with the institution by the Brazilian government of the National Alcohol Program (PRO-ÁLCOOL), as a consequence of the petroleum crisis, rising again five years ago, with the development of flex fuel cars. The obtaining process of ethanol originates residues; amongst them, vinasse is the one that’s generated in the largest amount (an average of 10 to 13 litres/litre of ethanol produced). The disposal of this residue in waters was only forbidden in 1978, but before that, researchers had already been investigating its utilization as raw material. This paper had the objective of accompany the biodegradation of vinasse by evaluating the oxygen comsumption during it until the ultimate Biochemical Oxygen Demand (uBOD), performed in twenty days; another objective was to analyse the biomass production of Saccharomyces cerevisae in this residue. Physical and chemical analyses of the residue were also performed, as well as acute toxicity essays using Daphnia similis and Dugesia tigrina, before and after its biodegradation. The physical and chemical analyses pointed elevated acidness (pH = 3,98), conductivity (8,30 mS/cm) and COD (25.693,43 mg O2/L) and mean quantity of suspended solids (5.246 mg/L). The toxicity essays indicated absence of toxic potential in vinasse after biodegradation for both species. The uBOD degradated until 88,22% of the COD, demonstrating the possibility of biodegradation of most of the residue’s organic load in a relatively short period of time. S. cerevisae caused a 37,03% COD diminution in vinasse, diminished its conductivity and promoted a slight elevation of the pH; it obtained low biomass...(Complete abstract click electronic access below)

Proposta de traçado de alcoolduto ligando a hidrovia Tietê Paraná à refinaria do planalto paulista com uso de avaliação multicritérios e geotecnologias

From the beginning of the century, with the advent of the flex fuel car, successor fluctuations in oil prices and the rise of awareness of the impending shortage of fossil fuels, the alcohol sector begins to reappear in the panorama of national economy making Brasill reaches the point of becoming a leading exporter of this product. Ethanol assumed the role of such importance in Brazilian exports, which Petrobras through the Growth Acceleration Program (PAC) has made investments in the Brazilian pipeline network to better ensure the production of ethanol to major ports. The means of transport in pipelines are safe and inexpensive, but require careful evaluation in its implementation, they may lead to negative social and environmental impacts. Thus, the purpose of this project is to propose the best route for an ethanol pipeline connectin the Tietê-Paraná, leaving the municipality of Santa Maria da Serra (SP), to the Planalto Paulista Refinery (REPLAN), located in Paulinia (SP), belonging to the passage of ethanol export corridor, currently under revelopment. The technique used for the development of the stroke is the association of multicriteria evaluation, the geographical information system (SIG) and geotechnologies. This study presented three possible layouts for the ethanol pipeline, highlighting the best option, in addition, demonstrated the suitability of the area to receive projects of similar nature to a pipeline

Campesinato e agrohidronegócio canavieiro no Pontal do Paranapanema: os desafios para a transição agroecológica

This paper appears in order to promote a discussion on the use and ways of working with the land. For this, we present a scenario of conflict initiated in Pontal do Parananema, São Paulo, Brazil, between the peasantry and the agrohidronegócio. The Pontal is a territory marked by agrarian and land conflicts, originated by the illegal occupation of land by the squatters, the decimation / expropriation of indigenous, and deforestation and environmental devastation. This conflict is represented today by the sugarcane agro-industrial capital companies on one side, and the other peasants. The expansion occurs agrohidronegócio strongly from 2005, due mainly to the change in the energy matrix of the country and state incentives with strong momentum in the production of flex-fuel vehicles. Rural agrarian reform settlements, made possible by the state under pressure from social movements, are spatialized in 16 municipalities with a total of 112 settlements, occupying an area of 139. 682 hectares, seating 5. 892 families. These families have seen their possibilities of social reproduction increasingly suppressed by the advance of sugarcane agrohidronegócio in the region, which suffocates the living spaces and work of these peasants. Front of it, agroecology is an alternative for these workers to ensure their reproductive possibilities. Agroecology also arises as a means of confronting agribusiness model, adding elements to the environment, such as the eradication of the use of pesticides and considering the dynamics of nature to promote agriculture, and social order, contributing food sovereignty and the production of healthy food and diversity to the population...

Eficácia da utilização de grânulos de argila como veículo para a aplicação aérea de sulfentrazone e isoxaflutole em área de implantação de eucalipto

Realizou-se um experimento em uma área de implantação da cultura do eucalipto no município de São Miguel Arcanjo-SP, com o objetivo de avaliar a eficácia da aplicação aérea de grânulos de argila como veículo dos herbicidas sulfentrazone e isoxaflutole, no controle de plantas daninhas. Foi realizada aplicação aérea dos herbicidas sulfentrazone, nas doses de 500 e 750 g i.a. ha-1, e isoxaflutole, nas doses de 150 e 225 g i.a. ha-1, utilizando-se como veículo grânulos de argila com densidade de 1,05 g cm ³, alta capacidade de absorção (24 mL 100 g-1), alta resistência ao desgaste e tamanho das partículas entre 500 mícrons e 1 mm. Também foram feitas aplicações via líquida dos mesmos herbicidas e doses com um pulverizador convencional, acoplado a um trator. Além desses tratamentos, foi mantida uma parcela testemunha, sem aplicação dos herbicidas. Nas parcelas experimentais foram semeadas as espécies de plantas daninhas Brachiaria decumbens, Ipomoea grandifolia, Merremia cissoides e Panicum maximum, sendo realizadas avaliações visuais de controle aos 75 e 110 dias após a aplicação. em geral, foram observados, nas plantas daninhas avaliadas, resultados de controle semelhantes ou superiores para a aplicação aérea (via grânulos) até 75 DAA e superiores para essa modalidade de aplicação aos 110 DAA, indicando uma extensão no período do efeito do residual dos herbicidas estudados.

Briquetting of charcoal from sugar-cane bagasse fly ash (scbfa) as an alternative fuel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Analysis of a molten carbonate fuel cell: cogeneration to produce electricity and cold water

The fuel cell is an emerging cogeneration technology that has been applied successfully in Japan, the USA and some countries in the European Union. This system performs direct conversion of the chemical energy of the oxidation of hydrogen from fuel with atmospheric oxygen into direct current electricity and waste heat via an electrochemical process relying on the use of different electrolytes (phosphoric acid, molten carbonate and solid oxide, depending on operating temperature). This technology permits the recovery of waste heat, available from 200 degreesC up to 1000 degreesC depending on the electrolyte technology, which can be used in the production of steam, hot or cold water, or hot or cold air, depending on the associated recuperation equipment. In this paper, an energy, exergy and economic analysis of a fuel cell cogeneration system (FCCS) is presented. The FCCS is applied in a segment of the tertiary sector to show that it is a feasible alternative for rational decentralized energy production under Brazilian conditions. The technoeconomic analysis shows a global efficiency or fuel utilization efficiency of 86%. Analysis shows that the exergy losses in the fuel cell unit and the absorption refrigeration system are significant. Furthermore, the payback period estimated is about 3 and 5 years for investments in fuel cells of 1000 and 1500 US$/kW, respectively. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Fuel cell cogeneration system: a case of technoeconomic analysis

Fuel Cell is the emerging technology of cogeneration, and has been applied successfully in Japan, U.S.A. and some OECD countries. This system produces electric power by an electrolytic process, in which chemical substances (the most utilized substances are solid oxide, phosphoric acid and molten carbonate) absorb the components H-2 and O-2 of the combustion fuel. This technology allows the recovery of residual heat, available from 200 degrees C up to 1000 degrees C (depending on the electrochemical substance utilized), which can be used for the production of steam, hot or cold water, or hot or cold air, depending on the recuperation equipment used. This article presents some configurations of fuel cell cogeneration cycles and a study of the technical and economic feasibility for the installation of the cogeneration systems utilizing fuel cell, connected to an absorption refrigeration system for st building of the tertiary sector, subject to conditions in Brazil. (C) 1999 Elsevier B.V. Ltd. All rights reserved.

Thermodynamic analysis of direct steam reforming of ethanol in molten carbonate fuel cell

Fuel cell as molten carbonate fuel cell (MCFC) operates at high temperatures. Thus, cogeneration processes may be performed, generating heat for its own process or for other purposes of steam generation in the industry. The use of ethanol is one of the best options because this is a renewable and less environmentally offensive fuel, and is cheaper than oil-derived hydrocarbons, as in the case of Brazil. In that country, because of technical, environmental, and economic advantages, the use of ethanol by steam reforming process has been the most investigated process. The objective of this study is to show a thermodynamic analysis of steam reforming of ethanol, to determine the best thermodynamic conditions where the highest volumes of products are produced, making possible a higher production of energy, that is, a more efficient use of resources. To attain this objective, mass and energy balances were performed. Equilibrium constants and advance degrees were calculated to get the best thermodynamic conditions to attain higher reforming efficiency and, hence, higher electric efficiency, using the Nernst equation. The advance degree (according to Castellan 1986, Fundamentos da Fisica/Quimica, Editora LTC, Rio de Janeiro, p. 529, in Portuguese) is a coefficient that indicates the evolution of a reaction, achieving a maximum value when all the reactants' content is used of reforming increases when the operation temperature also increases and when the operation pressure decreases. However, at atmospheric pressure (1 atm), the advance degree tends to stabilize in temperatures above 700 degrees C; that is, the volume of supplemental production of reforming products is very small with respect to high use of energy resources necessary. The use of unused ethanol is also suggested for heating of reactants before reforming. The results show the behavior of MCFC. The current density, at the same tension, is higher at 700 degrees C than other studied temperatures such as 600 and 650 degrees C. This fact occurs due to smaller use of hydrogen at lower temperatures that varies between 46.8% and 58.9% in temperatures between 600 and 700 degrees C. The higher calculated current density is 280 mA/cm(2). The power density increases when the volume of ethanol to be used also increases due to higher production of hydrogen. The highest produced powers at 190 mA/cm(2) are 99.8, 109.8, and 113.7 mW/cm(2) for 873, 923, and 973 K, respectively. The thermodynamic efficiency has the objective to show the connection among operational conditions and energetic factors, which are some parameters that describe a process of internal steam reforming of ethanol.

Preconcentration and determination of metal ions in commercial ethanol used as fuel for automotive engines

The present investigation reports the synthesis, characterization, and adsorption properties of a new nanomaterial based on organomodified silsesquioxane nanocages. The adsorption isotherms for CuCl,, CoCl2, ZnCl2, NiCl2, and FeCl3 from ethanol solutions were performed by using the batchwise method. The equilibrium condition is reached very quickly (3 min), indicating that the adsorption sites are well exposed. The results obtained in the flow experiments, showed a recovery of ca. 100% of the metal ions adsorbed in a column packed with 2 g of the nanomaterial, using 5 mL of 1.0 mol L-1 HCl solution as eluent. The sorption-desorption of the metal ions made possible the development of a method for preconcentration and determination of metal ions at trace level in commercial ethanol, used as fuel for car engines. The values determined by recommended method for plants 1, 2, and 3 indicated an amount of copper of 51, 60, and 78 mu g L-1, and of iron of 2, 15, and 13 mu g L-1, respectively. These values are very close to those determined by conventional analytical methods. Thus, these similar values demonstrated the accuracy of the determination by recommended method.

Voltammetric determination of total iron in fuel ethanol using a 1,10 fenantroline/nafion carbon paste-modified electrode

This work presents a methodology for iron determination in fuel ethanol using a modified carbon paste electrode with 1.10 fenantroline/nafion. The electrochemical parameters were optimized for the proposed system and the voltammetric technique of square wave was employed for iron determination. An accumulation time of 5 minutes, such as a 100 mV of pulse magnitude (E(sw)) and frequency (f) of 25 Hz were used as optimized experimental conditions. The modified carbon paste electrode presented linear dependence of amperometric signal with iron concentration in a work range from 6.0x10(-6) until 2.0x10(-5) mol L(-1) of iron, exhibiting a linear correlation coefficient of 0.9884, a detection limit of 2.4 x10(-6) mol L(-1) (n = 3) and amperometric sensibility of 4.5x10(5) mu A/mol L(-1). Analytical curve method was used for iron determination at a commercial fuel sample. Flame atomic absorption spectroscopy was employed as comparative technique.

Application of cellulose modified with p-aminobenzoic groups in preconcentration system for determination of Cu, Fe, Ni, and Zn in fuel ethanol samples by flame atomic absorption spectrometry

Cellulose chemically modified with p-aminobenzoic groups, abbreviated as Cel-PAB, was used for preconcentration of copper, iron, nickel, and zinc from ethanol fuel, normally used in Brazil as engine fuel. The surface characteristics and the surface area of the cellulose were obtained before and after chemical modification using FT-IR, elemental analysis, and surface area analysis (B.E.T.). The retention and recovery of the analyte elements were studied by applying batch and column techniques.