Influence of voids on the flexural resistance of the NCF/RTM6 composites

A major difficulty to achieve maximum weight savings in the manufacture of composite structural components, is the tendency of these materials have the formation of voids and cracks in the interior and surface components. In aeronautical applications, controlling the volume fraction of fibers, resins and empty the components of composite is very hard. In this work, composites of epoxy matrix RTM6 reinforced with NCF (non crimp fabric carbon) processed by resin transfer molding (RTM) were characterized for porosity (P-ap) and density (rho(ad)). We used a method based on Archimedes' principle (ASTM C830) and the technique of helium pycnometer. The porosity values were compared with those determined by acid digestion (ASTM D3171). The mechanical properties of processed composites was evaluated by testing on the performing flexural and the results were correlated with the porosity value. All techniques tested to determine void content are satisfactory. The differents results can be justified for heterogeneous void distribution on laminate and differences among techniques characteristics. (C) 2011 Published by Elsevier Ltd. Selection and/or peer-review under responsibility of ICM11

Influence of voids in the hybrid layer based on self-etching adhesive systems: a 3-D FE analysis

The presence of porosities at the dentin/adhesive interface has been observed with the use of new generation dentin bonding systems. These porosities tend to contradict the concept that etching and hybridization processes occur equally and simultaneously. Therefore, the aim of this study was to evaluate the micromechanical behavior of the hybrid layer (HL) with voids based on a self-etching adhesive system using 3-D finite element (FE) analysis. Three FE models (Mr) were built: Mr, dentin specimen (41x41x82 μm) with a regular and perfect (i.e. pore-free) HL based on a self-etching adhesive system, restored with composite resin; Mp, similar to M, but containing 25% (v/v) voids in the HL; Mpp, similar to Mr, but containing 50% (v/v) voids in the HL. A tensile load (0.03N) was applied on top of the composite resin. The stress field was obtained by using Ansys Workbench 10.0. The nodes of the base of the specimen were constrained in the x, y and z axes. The maximum principal stress (σmax) was obtained for all structures at the dentin/adhesive interface. The Mpp showed the highest peak of σmax in the HL (32.2 MPa), followed by Mp (30 MPa) and Mr (28.4 MPa). The stress concentration in the peritubular dentin was high in all models (120 MPa). All other structures positioned far from voids showed similar increase of stress. Voids incorporated into the HL raised the σmax in this region by 13.5%. This behavior might be responsible for lower bond strengths of self-etching and single-bottle adhesives, as reported in the literature.

Avaliação do ciclo térmico de conformação por compressão de peças em poli(sulfeto de fenileno) reforçado com fibras contínuas de carbono

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Flexural Test on Recycled Polystyrene

In socio-environmental scenario increased the nature resources concern beyond products and subproducts reuse. Recycling is the approach for a material or energy reintroducing in productive system. This method allows the reduction of garbage volume dumped in environment, saving energy and decreasing the requirement of natural resources use. In general, the ending of expanded polystyrene is deposited sanitary landfills or garbage dumps without control that take large volume and spreads easily by aeolian action, with consequently environmental pollution, however, the recycling avoids their misuse and the obtainment from petroleum is reduced. This work recycled expanded polystyrene via merger and/or dissolution by solvents for the production of integrated circuits boards. The obtained material was characterized in flexural mode according to ASTM D 790 and results were compared with phenolite, traditionally used. Specimens fractures were observed by electronic microscopy scanning in order to establish patterns. Expanded Polyestirene recycled as well as phenolite were also thermo analyzed by TGA and DSC. The method using dissolution produced very brittle materials. The method using merger showed no voids formation nor increased the brittleness of the material. The recycled polystyrene presented a strength value significantly lower than that for the phenolite. (C) 2011 Published by Elsevier Ltd. Selection and peer-review under responsibility of ICM11

Malformação arteriovenosa uterina após doença trofoblástica gestacional

OBJETIVO: investigar a presença e resultados de malformações vasculares uterinas (MAVU) após doença trofoblástica gestacional (DTG). MÉTODOS: estudo retrospectivo com inclusão de casos diagnosticados entre 1987 e 2004; 2764 pacientes após DTG foram acompanhadas anualmente com ultra-sonografia transvaginal e Doppler colorido no Centro de Neoplasia Trofoblástica Gestacional da Santa Casa da Misericórdia (Rio de Janeiro, RJ, Brasil). Sete pacientes tiveram diagnóstico final de MAVU baseado em análise ultra-sonográfica - índice de pulsatilidade (IP), índice de resistência (IR) e velocidade sistólica máxima (VSM) - e achados de imagens de ressonância nuclear magnética (RNM). Dosagens negativas de beta-hCG foram decisivas para estabelecer o diagnóstico diferencial com DTG recidivante. RESULTADOS: a incidência de MAVU após DTG foi 0,2% (7/2764). Achados ultra-sonográficos de MAVU: IP médio de 0,44±0,058 (extremos: 0,38-0,52); IR médio de 0,36±0,072 (extremos: 0,29-0,50); VSM média de 64,6±23,99 cm/s (extremos: 37-96). A imagem de RNM revelou útero aumentado, miométrio heterogêneo, espaços vasculares tortuosos e vasos parametriais com ectasia. A apresentação clínica mais comum foi hemorragia transvaginal, presente em 52,7% (4/7) dos casos. Tratamento farmacológico com 150 mg de acetato de medroxiprogesterona foi empregado para controlar a hemorragia, após a estabilização hemodinâmica. Permanecem as pacientes em seguimento, assintomáticas até hoje. Duas pacientes engravidaram com MAVU, com gestações e partos exitosos. CONCLUSÃO: presente sangramento transvaginal em pacientes com beta-hCG negativo e história de DTG, deve-se considerar a possibilidade de MAVU e solicitar avaliação ultra-sonográfica com dopplervelocimetria. O tratamento conservador é a melhor opção na maioria dos casos de MAVU pós-DTG.

Effects of laser-weld joint opening size on fatigue strength of Ti-6Al-4V structures with several diameters

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structure formation in the presence of dark energy perturbations

We study non-linear structure formation in the presence of dark energy. The influence of dark energy on the growth of large-scale cosmological structures is exerted both through its background effect on the expansion rate, and through its perturbations. In order to compute the rate of formation of massive objects we employ the spherical collapse formalism, which we generalize to include fluids with pressure. We show that the resulting non-linear evolution equations are identical to the ones obtained in the pseudo-Newtonian approach to cosmological perturbations, in the regime where an equation of state serves to describe both the background pressure relative to density, and the pressure perturbations relative to the density perturbations. We then consider a wide range of constant and time-dependent equations of state (including phantom models) parametrized in a standard way, and study their impact on the non-linear growth of structure. The main effect is the formation of dark energy structure associated with the dark matter halo: non-phantom equations of state induce the formation of a dark energy halo, damping the growth of structures; phantom models, on the other hand, generate dark energy voids, enhancing structure growth. Finally, we employ the Press-Schechter formalism to compute how dark energy affects the number of massive objects as a function of redshift (number counts).

Detecção de cavidades em arenitos utilizando gravimetria, eletrorresistividade e GPR

Este trabalho mostra os resultados obtidos com a realização de ensaios geofísicos na em áreas de lavra de areia, no município de Descalvado, SP. O objetivo dos ensaios é o de detectar cavidades no interior de arenitos, pertencentes às Formações Pirambóia e Botucatu. Estas cavidades formaram-se com o rebaixamento do lençol freático, necessário para as operações de extração da areia. As técnicas geofísicas utilizadas foram: gravimetria, eletrorresistividade (caminhamento elétrico dipolo-dipolo) e radar de penetração no solo (GPR). Na primeira etapa dos trabalhos foram utilizados a gravimetria e a eletrorresistividade em uma bancada onde ocorreu um desmoronamento devido ao abatimento do teto de uma cavidade. Os resultados obtidos com estas duas técnicas foram coerentes pois a gravimetria mostrou baixos gravimétricos indicando uma ausência de massa na área de influência da cavidade e o caminhamento detectou um esperado aumento de resistividade elétrica nesta mesma área. Na segunda etapa, com a realização dos ensaios de GPR em uma bancada próxima à anterior, foi possível detectar cavidades por meio das feições hiperbólicas detectadas nos radargramas.

A study of the microstructural characteristics of dental amalgams

Metallographic studies by scanning electron microscopy and energy dispersive spectroscopy carried out for two types of dental amalgam showing a porous multiphase material. Surface analysis shows that the structure of the Dispersalloy amalgam consists of gamma-Ag3Sn, gamma(1)-Ag2Hg3, eta'-Cu6Sn5, epsilon-Cu3Sn and eutectic Ag-Cu phases. while Velvalloy amalgam consists mainly of gamma, gamma(1) and gamma(2)-Sn7-8Hg phases. The latter phase presents an uniform distribution often associated with voids.

Sprawl e o modal de transporte motorizado: impactos na cidade de Londrina, PR

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Podzolization as a deferralitization process: a study of an Acrisol-Podzol sequence derived from Palaeozoic sandstones in the northern upper Amazon Basin

Morphological, geochemical and mineralogical studies were carried out in a representative soil catena of the low-elevation plateaux of the upper Amazon Basin to interpret the steps and mechanisms involved in the podzolization of low-activity clay soils. The soils are derived from Palaeozoic sandstones. They consist of Hydromorphic Podzols under tree savannah in the depressions of the plateaux and predominantly of Acrisols covered by evergreen forest elsewhere.Incipient podzolization in the uppermost Acrisols is related to the formation of organic-rich A and Bhs horizons slightly depleted in fine-size particles by both mechanical particle transfer and weathering. Weathering of secondary minerals by organic acids and formation of organo-metallic complexes act simultaneously over short distances. Their vertical transfer is limited. Selective dissolution of aluminous goethite, then gibbsite and finally kaolinite favour the preferential cheluviation of first Fe and secondly Al. The relatively small amount of organo-metallic complexes produced is related to the quartzitic parent materials, and the predominance of Al over Fe in the spodic horizons is due to the importance of gibbsite in these low-activity clay soils.Morphologically well-expressed podzols occur in strongly iron-depleted topsoils of the depression. Mechanical transfer and weathering of gibbsite and kaolinite by organic acids is enhanced and leads to residual accumulation of sands. Organo-metallic complexes are translocated in strongly permeable sandy horizons and impregnate at depth the macro-voids of embedded soil and saprolite materials to form the spodic Bs and 2BCs horizons. Mechanical transfer of black particulate organic compounds devoid of metals has occurred later within the sandy horizons of the podzols. Their vertical transfer has formed well-differentiated A and Bh horizons. Their lateral removal by groundwater favours the development of an albic E horizon. In an open and waterlogged environment, the general trend is therefore towards the removal of all the metals that have initially accumulated as a response to the ferralitization process and have temporarily been sequestrated in organic complexes in previous stages of soil podzolization.

Nanostructure and properties of ZnO films produced by the pyrosol process

Indium doped ZnO films were deposited by the pyrosol process on glass substrates at different temperatures from solutions containing In/Zn molar ratios up to 10%. The nanostructure of the films was investigated using grazing-incidence small angle X-ray scattering (GISAXS). The mass density was determined by X-ray reflectivity and the composition by X-ray photoelectron spectroscopy. The GISAXS measurements revealed an anisotropic pattern for films deposited at 573 and 623 K and a isotropic one for those deposited at higher temperatures. The anisotropic patterns indicate the presence of elongated nanopores with their long axes perpendicular to the film surface. In contrast, the isotropic nature of GISAXS patterns of films grown at high temperatures (673 and 723 K) suggests the presence of spherical voids. The pore size distribution function determined from the isotropic patterns indicates a multimodal size distribution. on the other hand, the measured mass density of the doped films with isotropic nanotexture is higher than that of the anisotropic films while the electric resistivity is significantly lower. This is in agreement with the detected strong reduction of the void density and specific surface area at approximately constant pore size.

Mullite whiskers grown from erbia-doped aluminum hydroxide-silica gel

Mullite whiskers and anisotropic grains that were derived from erbia-doped aluminum hydroxide-silica gel were studied. Firing 3.0-mol%-erbia-doped isostatically pressed pellets at 1600 degrees C for 1.0-8.0 h resulted in a high surface concentration of mullite whiskers. Their c-axes were aligned preferentially along the pellet surface; the maximum length was 50 mu m, and the maximum aspect ratio was 23. The pellet surface was fully covered by mullite whiskers, and small anisotropic grains with a low aspect ratio were observed in the bulk. The voids that were observed in the fracture surfaces were covered fully by mullite whiskers. The large number of voids resulted in an apparent density of 1.60 g/cm(3) in the sintered pellets. The molar ratio of alumina to silica in the whiskers was in the range of 1.30-1.45 tan average value of 1.31), regardless of whether the alumina/silica powder compositions were mixed in a 3:2 or 2:1 ratio.

Effects of self-assembly process of latex spheres on the final topology of macroporous silica

This paper surveys the topology of macroporous silica prepared using latex templates covering the submicrometric range (0.1-0.7 mu m). The behavior of latex spheres in aqueous dispersion has been analyzed by dynamic light scattering (DLS) measurement indicating the most appropriate conditions to form well-defined cubic arrays. The optical behavior of latex spheres has been analyzed by transmittance and reflectance measurements in order to determine their diameter and filling factor when they were assembled in bidimensional arrays. Macroscopic templates have been obtained by a centrifugation process and their crystalline ordering has been confirmed by porosimetry and scanning electron microscopy. These self-assembled structures have been used to produce macroporous silica, whose final topology depends on the pore size distribution of the original template. It has been seen that latex spheres are ordered in a predominant fcc arrangement with slipping of tetragonal pores due to the action of attractive electrostatic interactions. The main effect is to change the spherical shape of voids in macroporous silica into a hexagonal configuration with possible applications to fabricate photonic devices with novel optical properties. (c) 2005 Elsevier B.V. All rights reserved.

Morphology and topography analysis of mesoporous titania templated by micrometric latex sphere arrays

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)