Influence of air abrasion tips and operation modes on enamel-cutting characteristics

Objective: To assess the influence of air abrasion tips and system operation modes on enamel cutting. Methods: Forty bovine teeth were abraded with the air abrasion system Mach 4.1 for 10 and 15 seconds, employing conventional and sonic tips of 0.45-mm inner diameter and a 90° angle, and 27.5-μm aluminum oxide at 5.51 bar air pressure in continuous and pulsed modes. The width and depth of the resulting cuts were measured in SEM. Results: The multivariate analysis of variances revealed that, compared to the sonic tip, the conventional tip produced shallower cuts independent of the operation mode and the application period. Conclusions: The cutting patterns observed in this study suggest that the pulsed mode produced deeper cuts when both the conventional and sonic tips were used, and that the sonic tip cut more dental tissue than the conventional one.

Leishmania amazonensis Promastigotes Present Two Distinct Modes of Nucleus and Kinetoplast Segregation during Cell Cycle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparative analysis between overlapping and non-overlapping operation modes for the PWM buck converter using the three-state switching cell

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Photodetection with gate-controlled lateral BJTs from standard CMOS technology

The silicon-based gate-controlled lateral bipolar junction transistor (BJT) is a controllable four-terminal photodetector with very high responsivity at low-light intensities. It is a hybrid device composed of a MOSFET, a lateral BJT, and a vertical BJT. Using sufficient gate bias to operate the MOS transistor in inversion mode, the photodetector allows for increasing the photocurrent gain by 106 at low light intensities when the base-emitter voltage is smaller than 0.4 V, and BJT is off. Two operation modes, with constant voltage bias between gate and emitter/source terminals and between gate and base/body terminals, allow for tuning the photoresponse from sublinear to slightly above linear, satisfying the application requirements for wide dynamic range, high-contrast, or linear imaging. MOSFETs from a standard 0.18-μm triple-well complementary-metal oxide semiconductor technology with a width to length ratio of 8 μm /2 μm and a total area of ∼ 500μm2 are used. When using this area, the responsivities are 16-20 kA/W. © 2001-2012 IEEE.

A novel voltage step-down/up ZCS-PWM Zeta converter

This paper presents an analysis of a novel pulse-width-modulated (PWM) voltage step-down/up Zeta converter, featuring zero-current-switching (ZCS) at the active switches. The applications in de to de and ac to de (rectifier) operation modes are used as examples to illustrate the performance of this new ZCS-PWM Zeta converter. Regarding to the new ZCS-PWM Zeta rectifier proposed, it should be noticed that the average-current mode control is used in order to obtain a structure with high power-factor (HPF) and low total harmonic distortion (THD) at the input current.Two active switches (main and auxiliary transistors), two diodes, two small resonant inductors and one small resonant capacitor compose the novel ZCS-PWM soft-commutation cell, used in these new ZCS-PWM Zeta converters. In this cell, the turn-on of the active switches occurs in zero-current (ZC) and their turn-off in zero-current and zero-voltage (ZCZV). For the diodes, their turn-on process occurs in zero-voltage (ZV) and their reverse-recovery effects over the active switches are negligible. These characteristics make this cell suitable for Insulated-Gate Bipolar Transistors (IGBTs) applications.The main advantages of these new Zeta converters, generated from the new soft-commutation cell proposed, are possibility of obtaining isolation (through their accumulation inductors), and high efficiency, at wide load range. In addition, for the rectifier application, a high power factor and low THD in the input current ran be obtained, in agreement with LEC 1000-3-2 standards.The principle of operation, the theoretical analysis and a design example for the new de to de Zeta converter operating in voltage step-down mode are presented. Experimental results are obtained from a test unit with 500W output power, 110V(dc) output voltage, 220V(dc) input voltage, operating at 50kHz switching frequency. The efficiency measured at rated toad is equal to 97.3%for this new Zeta converter.Finally, the new Zeta rectifier is analyzed, and experimental results from a test unit rated at 500W output power, 110V(dc) output voltage, 220V(rms) input voltage, and operating at 50kHz switching frequency, are presented. The measured efficiency is equal to 96.95%, the power-factor is equal to 0.98, and the input current THD is equal to 19.07%, for this new rectifier operating at rated load.

Quality of performance of the operation of sugarcane mechanized planting in day and night shifts

The sugarcane mechanized planting is becoming increasingly widespread in Brazil due to a higher operability and better working conditions offered to workers compared to other types of planting. Studies related to this topic are insufficient or scarce in Brazil. In this context, the aim of this study was to evaluate the operation quality of sugarcane mechanized planting in two operation shifts, by means of statistical process control. The mechanized planting was held on March 2012 and statistical design was completely randomized with two treatments, totaling 40 replications for the day shift and 40 replications for the night shift. The variables evaluated were: speed, engine rotation, engine oil pressure, water temperature of the engine, effective field capacity and the time consumption hourly and effective fuel. The use of statistical control charts showed that random intrinsic do not cause this process. The tractor alignment error showed outliers in the day and night shifts operations, indicating a possible delay in receiving the signal. The water temperature of the engine and the effective fuel consumption showed lower variability in nighttime operation with average values of 81°C and 22.66 L ha-1, respectively. The hourly fuel consumption had greater variability and consequently lower quality during the night of the operation, with an average consumption of 25.46 L h-1 while the day shift showed 26.86 L h-1.

Controle de Botryosphaeria ribis causador de seca de ponteiro em Corymbia citriodora, com extratos vegetais e fungicidas

A seca de ponteiros é uma doença que vem acarretando danos severos em plantas de eucalipto, causando cancros ao longo do ramo principal. O objetivo deste trabalho foi avaliar o efeito de fungicidas e extratos vegetais no controle de Botryosphaeria ribis. O teste in vitro dos fungicidas foi inteiramente casualizado com oito tratamentos: carbendazim, clorotalonil, difenoconazole, picoxystrobin + ciproconazole, ciproconazole, azoxystrobin, picoxystrobin e testemunha, quatro doses: 1 µg/mL, 10 µg/mL, 100 µg/mL e 1000 µg/mL; com cinco repetições. Após homogeneização do meio foram vertidas para as placas, repicado um disco de meio de cultura contendo o patógeno para estas placas e mantidas em BOD a 25°C por cinco dias. A avaliação foi feita através de medição diária do crescimento radial do micélio em centímetros. O delineamento experimental do controle químico a campo foi em fatorial 5x3, com cinco fungicidas e três métodos de aplicação (poda, pincelado e pulverizado), com quatro repetições. Foram feitas quatro aplicações, com intervalo de quinze dias. Os tratamentos foram: 1. azoxystrobin, 2. carbendazim, 3. clorotalonil + tiofanato-metílico, 4. difenoconazole e 5. testemunha. Simultaneamente foram feitas avaliações seguindo uma escala de notas de 1 a 6. O delineamento experimental do teste in vitro dos extratos vegetais foi em fatorial 5x4, com três repetições. Os tratamentos avaliados foram os extratos de: mil folhas, melão de são caetano, eucalipto , álcool e testemunha, nas concentrações de 5, 10, 15 e 20%. Os extratos e o álcool foram misturados ao meio de cultura previamente autoclavado, sendo estes colocados em placas de Petri. A avaliação foi feita através de medição diária do crescimento radial do micélio em centímetros. No teste com mudas o delineamento experimental foi em fatorial 2 x 2 x 4, sendo utilizado no experimento de duas procedências, dois modos de tratamento (preventivo e convencional) e quatro produtos para o controle (extrato de melão de são caetano, extrato de Corymbia citriodora, álcool e água). A inoculação do patógeno foi feita no caule das mudas. Foram feitas aplicações dos produtos e avaliações semanais. A avaliação foi feita através da contagem de plantas doentes. O ingrediente ativo carbendazin foi o que mostrou os melhores resultados in vitro diferindo estatísticamente dos outros tratamentos pelo teste Tukey a 1% de probabilidade; seguido pelo clorotalonil e difenoconazole. Todos os ingredientes ativos avaliados mostraram-se superiores a testemunha. A campo, azoxystrobin foi superior aos demais tratamentos e não houve diferença significativa entre os métodos de aplicação. In vitro, os extratos de mil folhas, melão e eucalipto não diferiram entre si pelo teste de Tukey a 5% de probabilidade. O álcool proporcionou a maior inibição do crescimento micelial e diferiu estatisticamente dos outros tratamentos utilizados. As concentrações de 10, 15 e 20% dos extratos não diferiram entre si, mas foram superiores a concentração de 5%. No teste em mudas, a aplicação preventiva mostrou-se superior a aplicação curativa, sendo que o álcool e o extrato de C. citriodora não diferiram entre si, mas foram superiores ao extrato de melão-de-são-caetano. Todos os produtos foram superiores a testemunha.

Stochastic stability for Markovian jump linear systems associated with a finite number of jump times

This paper deals with a stochastic stability concept for discrete-time Markovian jump linear systems. The random jump parameter is associated to changes between the system operation modes due to failures or repairs, which can be well described by an underlying finite-state Markov chain. In the model studied, a fixed number of failures or repairs is allowed, after which, the system is brought to a halt for maintenance or for replacement. The usual concepts of stochastic stability are related to pure infinite horizon problems, and are not appropriate in this scenario. A new stability concept is introduced, named stochastic tau-stability that is tailored to the present setting. Necessary and sufficient conditions to ensure the stochastic tau-stability are provided, and the almost sure stability concept associated with this class of processes is also addressed. The paper also develops equivalences among second order concepts that parallels the results for infinite horizon problems. (C) 2003 Elsevier B.V. All rights reserved.

The X-ray crystallographic structure of Escherichia coli branching enzyme

Branching enzyme catalyzes the formation of alpha-1,6 branch points in either glycogen or starch. We report the 2.3-Angstrom crystal structure of glycogen branching enzyme from Escherichia coli. The enzyme consists of three major domains, an NH2-terminal seven-stranded beta-sandwich domain, a COOH-terminal domain, and a central alpha/beta-barrel domain containing the enzyme active site. While the central domain is similar to that of all the other amylase family enzymes, branching enzyme shares the structure of all three domains only with isoamylase. Oligosaccharide binding was modeled or branching enzyme using the enzyme-oligosaccharide complex structures of various alpha-amylases and cyclodextrin glucanotransferase and residues were implicated in oligosaccharide binding. While most of the oligosaccharides modeled well in the branching enzyme structure, an approximate 50degrees rotation between two of the glucose units was required to avoid steric clashes with Trp(298) of branching enzyme. A similar rotation was observed in the mammalian alpha-amylase structure caused by an equivalent tryptophan residue in this structure. It appears that there are two binding modes for oligosaccharides in these structures depending on the identity and location of this aromatic residue.

Observation of a new boson at a mass of 125 GeV with the CMS experiment at the LHC

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Short Comments on an Energy Pumping Levels in a MEMS Gyroscope Vibrating Problem, by Using of an Global and Local Optimal Linear Control Design

This paper deals with an energy pumping that occurs in a (MEMS) Gyroscope nonlinear dynamical system, modeled with a proof mass constrained to move in a plane with two resonant modes, which are nominally orthogonal. The two modes are ideally coupled only by the rotation of the gyro about the plane's normal vector. We also developed a linear optimal control design for reducing the oscillatory movement of the nonlinear systems to a stable point.

Voltage-composition profile and synchrotron X-ray structural analysis of low and high temperature LixCoO2 host material

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sugarcane grown in an oxisol amended with sewage sludge and vinasse: nitrogen contents in soil and plant

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

EXAFS and XRD analyses of the structural evolutions involved during drying of SnO2 hydrogels

In order to determine structural changes during drying of inorganic gels, the local and long-range order structure of SnO2-x(OH)2x xerogels resulting from drying hydrogels with different concentrations of electrolyte (Cl- and NH+ 4) have been measured by extended X-ray absorption fine structure (EXAFS), X-ray diffraction (XRD) and N2 adsorption techniques. EXAFS measurements performed at the Sn K edge on the hydrogels and xerogels show the existence of microcrystallites with the cassiterite structure. Two drying modes have been used: freeze drying and drying by evaporation at 45°C. It is shown that the microcrystallite size determined by XRD and EXAFS techniques on the drying mode and on the electrolyte concentrations. The microcrystallite size measured on the freeze dried xerogels is similar to that of their parent hydrogels, whatever the concentration of electrolyte; however, during drying by evaporation, a preferential growth of microcrystallites along the c-axis of the cassiterite structure is observed. The size of these crystallites is enhanced with a decrease of the electrolyte concentration. Specific surface areas calculated by the Brunauer-Emmett-Teller method indicate that this preferential growth is related to the improvement of the network connectivity. The comparison of both drying processes indicates that crystallization and polycondensation are independent phenomena. © 1995 Elsevier Science B.V. All rights reserved.

The influence of chemical activation on hardness of dual-curing resin cements.

During the cementation of metallic restorations, the polymerization of dual-curing resin cements depends exclusively on chemical activation. This study evaluated the influence of chemical activation compared with dual-curing (chemical and light activation), on the hardness of four dual-curing resin cements. In a darkened environment, equal weight proportions of base and catalyst pastes of the cements Scotchbond Resin Cement, Variolink II, Enforce and Panavia F were mixed and inserted into moulds with cavities of 4 mm in diameter and 2 mm in height. Subsequently, the cements were: 1) not exposed to light (chemical activation = self-cured groups) or 2) photoactivated (dual-curing = dual-cured groups). The Vickers hardness number was measured at 1 hour, 24 hours and 7 days after the start time of cements' spatulation. For all the cements, the hardness values of self-cured groups were lower than those of the respective dual-cured groups at 1 hour and 24 hours. At 7 days, this behavior continued for Variolink II and Panavia F, whilst for Scotchbond Resin Cement and Enforce there was no statistical difference between the two activation modes. All cements showed a significant increase in their hardness values from 1 hour to 7 days for both activation modes. Of the self-cured groups, Scotchbond Resin Cement and Variolink II presented the highest and the lowest hardness values, respectively, for all three times tested. Within the limitations of this study, up to the time of 24 h, chemical activation alone was unable to promote similar hardness as to that obtained with dual-curing.