The position effect of structural Eucalyptus round timber on the flexural modulus of elasticity

A madeira roliça possui grande emprego nas construções civis, desempenhando a função de vigas, colunas, fundações, postes para distribuição de energia elétrica, entre outras, apresentando a vantagem de não ser processada, como é o caso da madeira serrada. O projeto envolvendo elementos roliços requer, além de outras variáveis estruturais, o conhecimento do módulo de elasticidade. No Brasil, os documentos normativos que tratam da determinação das propriedades de rigidez e resistência para peças roliças de madeira estão em vigência há mais de vinte anos sem revisão técnica. A madeira roliça, por geralmente possuir eixo com curvatura não nula, pode apresentar, segundo a posição da peça no ensaio de flexão, valores diferentes do módulo de elasticidade. Este trabalho tem como objetivo analisara influência da posição de peças roliças de madeira de Eucalyptus grandis na determinação do módulo de elasticidade na flexão. O ensaio de flexão utilizado é o de três pontos, sendo cada peça avaliada em duas posições distintas, definidas mediante o giro da seção transversal em torno do eixo. Os resultados encontrados indicam a necessidade do ensaio de flexão em, pelo menos, duas posições distintas da peça.

Study of the timber constructive systems that are more commercialized in Brazil

The Brazilian houses in wood are executed with several techniques and species, in function of the areas they are located, therefore, it is treated of regional traditional houses, built practically without modem technological resources. These houses are the ones of the tropical areas, where there is abundance of this material, or the ones of the south region, prevailing the European immigrant's constructive techniques. Nowadays, in the urbanized centers of the country it is observed that this type of house can be found sheltering the most lacking populations, in the slums; or in highly sophisticated residential units which are conceived and executed by specialist professionals for a social class of high purchasing power; or still, those that are marketed by companies of small load, that offer standardized residences, usually acquired by the middle class as second residence, in the field or in the coast. The work has for objective to study the houses of these companies that are consolidated at the market, identifying the constructive system, the product; as well as, its production process, trying to verify which technologies are incorporated to these processes. The analysis that was made allows a larger understanding of the product, wood house, that exists in the market and identification of the technological degree in the productive process of those constructive systems.

Electromyographic activity of shoulder muscles during exercises performed with oscillatory and non-oscillatory poles

CONTEXTUALIZAÇÃO: A dor e a disfunção no complexo articular do ombro é comumente encontrada na prática fisioterapêutica. Essas anormalidades musculoesqueléticas estão relacionadas à instabilidade e inadequado funcionamento cinemático, que dependem da integridade dos tecidos musculares. Assim, no sentido de prevenir e reabilitar esses sintomas, o uso da haste oscilatória vem sendo implantado para melhorar os resultados de técnicas cinesioterapêuticas. OBJETIVOS: Analisar a atividade eletromiográfica (EMG) dos músculos que estabilizam a articulação do ombro durante a realização de exercícios com haste oscilatória e haste não-oscilatória. MÉTODOS: Participaram do estudo 12 voluntárias com idade de 20,4±1,9 anos. Os dados EMG foram coletados nos músculos trapézio superior (TrS), trapézio inferior (TrI) e deltoide médio (DM) durante três diferentes exercícios realizados com haste oscilatória e haste não-oscilatória. O sinal EMG foi analisado no domínio do tempo pelo cálculo do Root Mean Square (RMS). Os valores de RMS foram normalizados pelo valor de pico obtido em todas as tentativas por cada músculo. A análise estatística foi feita com os testes ANOVA para medidas repetidas e post-hoc de Bonferroni. RESULTADOS: A atividade EMG dos músculos TrS, TrI e DM foi significativamente maior nos exercícios com haste oscilatória do que com haste não-oscilatória (todos p<0,001). Não foram significativas as diferenças na ativação desses músculos entre os exercícios. CONCLUSÃO: Os resultados do presente estudo indicaram que a haste oscilatória requisitou maior atividade EMG dos músculos do ombro e, assim, pode ser um instrumento útil no treinamento desses músculos.

Electromyographic activity of trunk muscles during exercises with flexible and non-flexible poles

Objective: Hand-held flexible poles which are brought into oscillation to cause alternating forces on trunk, are advocated as training devices that are supposed to solicit increased levels of stabilizing trunk muscle activity. The aim of this study was to verify this claim by comparing electromyographic (EMG) activity of trunk muscles during exercises performed with a flexible pole and a rigid pole.Methods: Twelve healthy females performed three different exercises with flexible and rigid poles. EMG activity of iliocostalis lumborum (IL), multifidus (MU), rectus abdominis (RA), external oblique (EO) and internal oblique (IO), and was continuously measured. The EMG signals were analyzed in time domain by calculation of the Root Mean Square (RMS) amplitudes over 250 ms windows. The mean RMS-values over time were normalized by the maximum RMS obtained for each muscle.Results: The IO showed a 72% greater EMG activity during the exercises performed with the flexible pole than with the rigid pole (p = 0.035). In exercises performed in standing, the IO was significantly more active than when sitting (p = 0.006).Conclusion: As intended, the cyclic forces induced by the oscillating pole did increase trunk muscle activation. However, the effect was limited and significant for the IO muscle only.

GHOST POLES IN THE NUCLEON PROPAGATOR - VERTEX CORRECTIONS AND FORM-FACTORS

Vertex corrections are taken into account in the Schwinger-Dyson equation for the nucleon propagator in a relativistic field theory of fermions and mesons. The usual Hartree-Fock approximation for the nucleon propagator is known to produce the appearance of complex (ghost) poles which violate basic theorems of quantum field theory. In a theory with vector mesons there are vertex corrections that produce a strongly damped vertex function in the ultraviolet. One set of such corrections is known as the Sudakov form factor in quantum electrodynamics. When the Sudakov form factor generated by massive neutral vector mesons is included in the Hartree-Fock approximation to the Schwinger-Dyson equation for the nucleon propagator, the ghost poles disappear and consistency with basic requirements of quantum field theory is recovered.

Ghost poles in the nucleon propagator in the linear sigma model approach and its role in pi N low-energy theorems

Complex mass poles, or ghost poles, are present in the Hartree-Fock solution of the Schwinger-Dyson equation for the nucleon propagator in renormalizable models with Yukawa-type meson-nucleon couplings, as shown many years ago by Brown, Puff and Wilets (BPW), These ghosts violate basic theorems of quantum field theory and their origin is related to the ultraviolet behavior of the model interactions, Recently, Krein et.al, proved that the ghosts disappear when vertex corrections are included in a self-consistent way, softening the interaction sufficiently in the ultraviolet region. In previous studies of pi N scattering using ''dressed'' nucleon propagator and bare vertices, did by Nutt and Wilets in the 70's (NW), it was found that if these poles are explicitly included, the value of the isospin-even amplitude A((+)) is satisfied within 20% at threshold. The absence of a theoretical explanation for the ghosts and the lack of chiral symmetry in these previous studies led us to re-investigate the subject using the approach of the linear sigma-model and study the interplay of low-energy theorems for pi N scattering and ghost poles. For bare interaction vertices we find that ghosts are present in this model as well and that the A((+)) value is badly described, As a first approach to remove these complex poles, we dress the vertices with phenomenological form factors and a reasonable agreement with experiment is achieved, In order to fix the two cutoff parameters, we use the A((+)) value for the chiral limit (m(pi) --> 0) and the experimental value of the isoscalar scattering length, Finally, we test our model by calculating the phase shifts for the S waves and we find a good agreement at threshold. (C) 1997 Elsevier B.V. B.V.

Reliability of timber bridges using nailed plywood box beams

The Nailed Box Beam structural efficiency is directly dependent of the flange-web joint behavior, which determines the partial composition of the section, as the displacement between elements reduces the effective rigidity of the section and changes the stress distribution and the total displacement of the section. This work discusses the use of Nailed Plywood Box Beams in small span timber bridges, focusing on the reliability of the beam element. It is presented the results of tests carried out in 21 full scale Nailed Plywood Box Beams. The analysis of maximum load tests results shows that it presents a normal distribution, permitting the characteristic values calculation as the normal distribution theory specifies. The reliability of those elements was analyzed focusing on a timber bridge design, to estimate the failure probability in function of the load level.

Portable Hardness tester for timber classification

Hardness is a property largely used in material specifications, mechanical and metallurgical research and quality control of several materials. Specifically for timber, Janka hardness is a simple, quick and easy test, with good correlations with the compression parallel to grain strength, a strong reference in structural classification for this material. More recently, international studies have reported the use of Brinell hardness for timber assessment which resumes the advantages previously mentioned for Janka hardness and make it easier to be performed in the field, especially because of the lower magnitude of the involved loads. A first generation of an equipment for field evaluation of hardness in wood - Portable Hardness tester for wood - based on Brinell hardness has already been developed by the Research Group on Forest Products from FCA/UNESP, Brazil, with very good correlations between the evaluated hardness and several other mechanical properties of the material when performing tests with different species of native and reforested wood (traditionally used as ties - sleepers - in railways). This paper presents results obtained in the experimental program with the first generation of this equipment and preliminary tests with its second generation, which uses accelerometers to substitute the indentation measurements in wood. For the first generation of the equipment functional and calibration tests were carried out using 16 native and reforestation timber lots, among there E. citriodora, E. tereticornis, E. saligna, E. urophylla, E. grandis, Goupia glabra and Bagassa guianenses, with different origins and ages. The results obtained confirm its potential in the classification of specimens, with inclusion errors varying from 4.5% to 16.6%.

The formation of the professionals for the timber industrial sector of the civil construction

The common point between the two forms of production of the wood-based sector in Brazil, one practically manufacturing and the other high technology, is in the qualification of the of the labor. In both cases, the professionals are being formed directly in the productive line and rarely with qualification in the academic area. There is not a public political education for the qualification of the labor, and the work market that does not demand qualified professionals, contributes for the sector stagnation. So, in order to excel the socio-cultural barriers in relation to the use of wood in the buildings, new attitudes are necessary in the teaching of the contents of the curricular programs, mainly, in formation of the architect and civil engineering.

Can overharvesting of a non-timber-forest-product change the regeneration dynamics of a tropical rainforest? The case study of Euterpe edulis

The exploitation of non-timber forest products is often considered a low-impact activity in tropical forests. However, assessments of the impacts of such activity are mostly focused on the harvested species and not on the plant community, thus limiting our understanding for establishing forest management recommendations. We investigated the consequences of Euterpe edulis palm heart harvesting on the seed rain in the Brazilian Atlantic rainforest. We compared the density of E. edulis individuals, as well as the density of E. edulis seeds, and the density, richness and functional composition of seed rain of the whole plant community, before and after palm heart harvesting in a 10 ha permanent plot. This assessment was carried out in preserved (typical old-growth Atlantic rainforest) and in disturbed (more open habitat dominated by the native bamboo Guadua tagoara) forest patches. Palm harvesting reduced the E. edulis population from 202.16 to 25.67 ind/ha and its seed rain density from 0.362 to 0.3 seeds/m2 and from 2.395 to 0.15 seeds/m2 in preserved and disturbed forest patches, respectively. Seed density of light-dependent climbers, pioneer trees, bamboo and animal-dispersed seeds increased after palm harvesting, especially in the disturbed forest patches, where palm harvesting was more intense and may have changed the light regime of the understory. On the other hand, species richness of the plant community declined by half. We observed a remarkable decline in the number of animal-dispersed species, especially for those with large seeds, suggesting that the activity of seed dispersers, including many species attracted by E. edulis fruits, was reduced. Therefore, harvesting of E. edulis palm heart may change the regeneration dynamics of the Atlantic rainforest, both due to shifts in forest structure, mediated by the removal of individuals from the forest canopy, and in community functioning, mediated by the interference on the activity of seed dispersers. © 2013 Elsevier B.V. All rights reserved.

Variação, herdabilidade e ganhos genéticos em progênies de eucalyptus tereticornis aos 25 anos de idade em Batatais – SP

Pós-graduação em Agronomia - FEIS

Variação, herdabilidade e ganhos genéticos em progênies de Eucalyptus tereticornis aos 25 anos de idade em Batatais-SP

The wood of Eucalyptus tereticornis is intensively used for timber, structures, buildings, poles, posts and coal. The aim of this study was to estimate genetic parameters and genetic and phenotypic correlations in growth and stem form traits of 52 open-pollinated progenies of E. tereticornis sampled from three Australian populations (20 progenies from Helenvale, 19 from Ravenshoe and 13 from Mt. Garnet). The progenies were compared with three commercial control also from Australian. The experimental design used was the compact family block, with the effect of provenance allocated in the plots and progenies within provenances in the subplots. Ten repetitions of the 52 treatments, sub-plots with six plants and the spacing of 3 x 2 m was used. At 25 years of age it was measured the diameter at breast height (DBH), total height, true volume and the stem form. We found genetic variation amon and within the three provenances and the possibility of obtaining high gains from mass selection and individual among and within progenies. The provenance Helenvale showed the best development for DBH, height and volume. The traits DBH, height and volume showed high genetic correlations (> 0.9), indicating the possibility to use the indirect selection. The coefficient of heritability on a progeny mean for the traits DBH and height was median, being 0.31 and 0.30, respectively. The expected genetic gain with the selection were estimated at 12.4% for DBH and 8.5 % for plant height. These results will subsidize the transformation of the provenance and progeny test in a seedling seed orchard and a clonal seed orchard.

Minimizing inter-genotypic competition effects to predict genetic values and selection in forestry genetic tests

The effect of competition is an important source of variation in breeding experiments. This study aimed to compare the selection of plants of open-pollinated families of Eucalyptus with and without the use of competition covariables. Genetic values were determined for each family and tree and for the traits height, diameter at breast height and timber volume in a randomized block design, resulting in the variance components, genetic parameters, selection gains, effective size and selection coincidence, with and without the use of covariables. Intergenotypic competition is an important factor of environmental variation. The use of competition covariables generally reduces the estimates of variance components and influences genetic gains in the studied traits. Intergenotypic competition biases the selection of open-pollinated eucalypt progenies, and can result in an erroneous choice of superior genotypes; the inclusion of covariables in the model reduces this influence.

Análise operacional e econômica do processamento de madeira de Eucalitpo com Hypro em região montanhosa

O processo constante de avaliação técnica e econômica dos sistemas de colheita de madeira é intrínseco às empresas florestais, devido ao fato de corresponder a uma fase de suma importância que despende elevado investimento financeiro. No experimento deste trabalho, estudaram-se o rendimento operacional e custos operacionais e de produção do processador florestal Hypro. A análise técnica englobou estudos de tempos e movimentos pelo método de tempo contínuo. O rendimento operacional foi determinado através do volume, em metros cúbicos de madeira processada. A análise econômica incorporou os parâmetros do custo operacional, custo de processamento da madeira e rendimento energético. A análise dos dados evidenciou que o rendimento operacional por hora efetiva de trabalho foi de 38 árvores e, em metros cúbicos sem casca por hora efetiva de trabalho, de 11,68 m³ h-1, com custo de processamento de madeira sem casca de US$ 6.85 por metro cúbico.

Efeito do tempo de experiência de operadores de Harvester no rendimento operacional

A mecanização da colheita de madeira permite maior controle dos custos e pode proporcionar reduções em prazos relativamente curtos. Além disso, tem um lugar de destaque na humanização do trabalho florestal e no aumento do rendimento operacional. O presente trabalho teve por objetivo avaliar o desempenho de operadores de harvester em função do tempo de experiência na atividade. Foram avaliados oito operadores do sexo masculino, com idade entre 23 e 46 anos. O estudo consistiu na análise do volume de madeira colhida pelo harvester. O tempo de experiência afeta significativamente o rendimento operacional dos operadores de harvester. Tal rendimento aumenta expressivamente nos primeiros 18 meses de experiência, mantendo-se em ascensão nos próximos 26 meses. Após os 44 meses de experiência, o rendimento dos operadores tende a reduzir, revelando as possíveis acomodações do cotidiano. Tais resultados permitem concluir que por volta dos 50 meses de experiência na atividade de operação de harvester, se faz necessária a adoção de medidas de reciclagem, motivação, entre outras, a fim de proporcionar aos operadores melhores condições de trabalho que os possibilitem continuar exercendo a atividade de forma eficiente e rentável à empresa.