The effect of thermal cycles on the mechanical properties of fiber-metal laminates

The effect of thermal-shock cycles on the mechanical properties of fiber-metal laminates (FMLs) has been evaluated. FML plates were composed by two AA2024 Al sheets (1.6 mm thick) and one composite ply formed by two layers of unidirectional glass fiber epoxy prepreg and two layers of epoxy adhesive tape of glass fiber reinforced epoxy adhesive. The set was manufactured by hand layup and typical vacuum bag technique. The curing cycle was in autoclave at 125 +/- 5 degrees C for 90 min and an autoclave pressure of 400 kPa. FML coupons taken from the manufactured plate were submitted to temperature variations between -50 and +80 degrees C, with a fast transition between these temperatures. Tensile and interlaminar shear strength were evaluated on samples after 1000 and 2000 cycles, and compared to nonexposed samples. 2000 Cycles corresponds to typical C Check interval for commercial aircraft maintenance programs. It was observed that the thermal-shock cycles did not result in significant microstructural changes on the FML, particularly on the composite ply. Similarly, no appreciable effect on the mechanical properties of FML was observed by the thermal-shock cycles. (c) 2012 Elsevier Ltd. All rights reserved.

Effect of combined bending strain and thermal cycling on the voltage-current characteristic curves of Bi-2223 tapes

High critical temperature superconductors are evolving from a scientific research subject into large-scale application devices. In order to meet this development demand they must withstand high current capacity under mechanical loads arising from thermal contraction during cooling from room temperature down to operating temperature (usually 77 K) and due to the electromagnetic forces generated by the current and the induced magnetic field. Among the HTS materials, the Bi2Sr2Ca2Cu3Ox, compound imbedded in an Ag/AgMg sheath has shown the best results in terms of critical current at 77 K and tolerance against mechanical strain. Aiming to evaluate the influence of thermal stress induced by a number of thermal shock cycles we have evaluated the V-I characteristic curves of samples mounted onto semicircular holders with different curvature radius (9.75 to 44.5 mm). The most deformed sample (epsilon = 1.08%) showed the largest reduction of critical current (40%) compared to the undeformed sample and the highest sensitivity to thermal stress (I-c/I-c0 = 0.5). The V-I characteristic curves were also fitted by a potential curve displaying n-exponents varying from 20 down to 10 between the initial and last thermal shock cycle.

Fatores que afetam a germinação e a emergência de Xanthium strumarim L.: dormência, qualidade da luz e profundidade de semeadura

Foram conduzidos três ensaios com o objetivo de estudar os efeitos de diferentes métodos de quebra de dormência das sementes, da qualidade da luz e da profundidade de semeadura na germinação e emergência do Xanthium strumarim L. (carrapichão). No primeiro ensaio, sob condições de câmara de crescimento, os tratamentos constaram de 5 métodos de quebra de dormência: mecânico (lixa), químico (H2SO4 conc. por 10 min.), pré-tratamento em água (imersão por 2 horas), físico (choque térmico: água à 80oC por 2 min.) e testemunha, que proporcionaram 100%, 93%, 93%, 87% e 80% de germinação, respectivamente, sem haver diferença estatística entre os mesmos. O pré-tratamento em água apresentou menor índice de velocidade de germinação (IVG) e os demais não diferiram significativamente entre si. No segundo ensaio, também sob condições de câmara de crescimento, os tratamentos de qualidade da luz constaram de 6 filtros de luz, que resultaram nas seguintes porcentagens de germinação: azul - com refletividade máxima a 450 nm (13%), verde-500 nm (33%), vermelho-700 nm (13%), vermelho/distante-760 nm (7%), ausência de luz (26%) e transparente - sem absortividade na região de 380 a 760 nm (testemunha, 73%), indicando sensibilidade das sementes à qualidade de luz. No terceiro ensaio, sob condições de casa-de-vegetação, os tratamentos foram diferentes profundidades de semeadura (0 a 20 cm, em intervalos de 2 cm), sendo que o máximo de emergência ocorreu no intervalo de 0 a 8 cm, no qual foi observado 67% de emergência do carrapichão, com maior índice de velocidade emergência (IVE), sendo que após os 16 cm, praticamente não houve emergência.

Esporos de Clostridium botulinum em mel comercializado no Estado de São Paulo e em outros Estados brasileiros

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Métodos de superação de dormência de sementes de barbatimão

The aim of this research was to identify methods for breaking dormancy and promoting germination of Stryphnodendron adstringens and S. polyphyllum seeds. Seeds of both species were submitted to the following treatments for breaking dormancy: control; mechanical scarification (sandpaper number 220); hot water (initial temperature of 87 degrees C) for 5 and 15 minutes; chemical scarification with H(2)SO(4) (95%) for 30, 45, 60, 75, 90 and 105 minutes; thermal shock 1 (0 degrees C and 50% RH for 1 h and thereafter 10 minutes into water Ti=85 degrees C, Tf=57 degrees C); thermic shock 2 (40 degrees C and 40% RH for 6 h and thereafter 10 minutes into water, Ti=0 degrees C, Tf=3 degrees C); thermal shock 3 (40 degrees C and 40% RH for 6h and thereafter 10 minutes into water, Ti=25 degrees C, Tf=25 degrees C). We concluded that seeds belonging to same genus but from different species answered differently to some treatments for breaking dormancy. Chemical scarification with H(2)SO(4) (45 minutes) and mechanical scarification with sandpaper are methods that can be employed with efficiency to break dormancy and promote germination for both species.

Improvement in RNA extraction from S. cerevisie by optimization in the autolysis and NH3 hydrolysis

The optimization of autolysis of Saccharomyces cerevisiae from brewery was studied aiming at the maximum ribonucleic acid extraction and yeast extract production. The best conditions for yeast autolysis was 55.2ºC, pH= 5.1 and 9.8% NaCl for 24h of processing, without the NH3 use. In these conditions, the RNA yield was 89.7%, resulting in 51.3% of dehydrated yeast extract with 57.9% protein. The use of 12.2% NH3 at 60ºC after autolysis (8h) and plasmolysis (8h) was not viable due to the reduction in the RNA yield from 89.7to78.4%. on the other hand, the thermal shock at 60ºC for 15 minutes prior to autolysis provided an increase in the yield from 89.7 to 91.4%. The autolysis, including NaCl plasmolysis in the optimized conditions was efficient, economic and with short time, thus usable for industrial purpose to obtain more valuable products such as yeast extract enriched in RNA and/or protein, for different applications.

Development of a new epoxy resin for superconducting magnet impregnation

A novel epoxy resin system based on a low viscosity Bisphenol-A (DGEBA)/Bisphenol-F (DGEBF) blend has been investigated for use in tight-wound superconducting magnet impregnation. The principle is to decrease the Bisphenol-A resin system viscosity by adding the low viscosity Bisphenol-F resin. The rheological and mechanical properties of the blend system are compared to the pure Bisphenol-A resin and also to the Bisphenol-F resin both cured with acid anhydride. For the vacuum/pressure impregnation, both the pure Bisphenol-F resin system and DGEBA/DGEBF blend system can be applied without S-glass fabric between coil layers due to its higher rigidity at low temperature and good resistance to thermal shock. This resin system have been tested for impregnation of copper and NbTi wire wound coils whilst Bisphenol-A resin system have been used for testing Nb3Sn coil impregnation where S-glass braid is present as wire insulation.

Critical current degradation of Bi-2223 composite tapes induced by cyclic deformation and fatigue-related effects

Application of high temperature superconductor Bi2Sr2Ca2Cu3Ox. (Bi-2223) compound embedded in an Ag matrix requires the knowledge of critical current as a function of mechanical properties. Commercial tapes available in different types have been developed in industrial production scale in which a combination of small diameter filaments, long tape lengths and a ductile matrix results in a conductor with low crack formation and good tolerance against strain. The measurement of critical current and the evaluation of n-index from V-I characteristic curves of Bi-2223/Ag composite tapes subjected to an initial bending strain as a function of number of thermal cycles were done for two types of Bi-2223/Ag composite tapes: with and without steel tape reinforcement. The results showed that tapes with reinforcement presented small critical current degradation as a function of the number of thermal cycles whereas tapes without reinforcement exhibited steadily critical current degradation caused by the propagation of cracks. The n-index followed the same critical current behavior.

Study of the presence of the spores of Clostridium botulinum in honey in Brazil

The isolation of Clostridium botulinum from honey samples is described. Botulism is characterized as an intoxication provoked by ingestion of contaminated foods with this toxin. Infant botulism happens by the ingestion of spores of C. botulinum together with food that in special conditions of the intestinal tract, such as those present in babies of less than 1 year old, will allow the germination and colonization of the intestine with production and absorption of botulinic toxin. The samples were subjected to dilution and to a thermal shock and cultivated in modified CMM (Difco). Cultures were subjected to Gram smears and toxicity tests in mice. The toxic cultures were purified in RFCA (Oxoid) plates and incubated in anaerobic jars. Positive samples were typed using the mouse assay neutralization test. From the 85 honey samples analyzed, six were positive for C. botulinum (7.06%), and identified as producers of type A, B, and D toxins.

Evaluation of weather influence on mechanical and viscoelastic properties of polyetherimide/carbon fiber composites

In order to investigate how environmental degradation affects the mechanical and thermal performance of polyetherimide/carbon fiber laminates, in this work different weathering were conducted. Additionally, dynamic mechanical analysis, interlaminar shear strength tests and non-destructive inspections were performed on this composite before and after being submitted to hygrothermal, UV radiation and thermal shock weathering. According to our results, hygrothermally aged samples had their glass transition temperature and elastic and storage moduli reduced by plasticization effect. Photooxidation, due to UV radiation exposure, occurred only on the surface of the laminates. Thermal shock induced a reversible stress on the composite's interface region. The results revealed that the mechanical behavior can vary during weather exposure but since this variation is only subtle, this thermoplastic laminate can be considered for high-performance applications, such as aerospace. © The Author(s) 2013.

Efeito do condicionamento ambiental em compósitos soldados de PPS/fibras contínuas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Produtividade de Agaricus blazei Murril em função do ambiente de cultivo, massa do substrato e camada de cobertura

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Use of mathematical models in the study of bodily growth in GIFT strain Nile tilapia

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Fractografia quantitativa e o conceito de tenacidade à fratura para a análise do efeitodo choque térmicos em TiO2

The present study evaluated the use of semicircular bending test (SCB) as an alternative to conventional bending test to examine the effect of thermal shock. Still, studies the behavior of fracture surfaces generated by monofractal behavior analysis, which allows us to evaluate the contributions of the microstructure and the mechanical context in forming reliefs during the crack propagation. The fractal analysis is made from elevation maps obtained by reconstruction method by extension of the focus stacks of digital images acquired in microscope. The specimens used were samples semicircular pressed TiO2 (rutile) with and without heat shock, prepared for testing mode I loading. Were also produced, specimens in the form of bars for Weibull statistical analysis. From the three-point bending test, we found the variation of fracture toughness between the samples after the heat shock and natural condition. The SCB test was feasible for the analysis of thermal shock resistance. The results showed that the value of the fracture toughness decreases as the heat shock treatment

Avaliação do efeito ambiental nas propriedades mecânicas e viscoelásticas de compósitos híbridos de titânio/fibra de carbono/resina epóxi

Hybrid composites combining metal plates and laminates with continuous fiber reinforced polymer, called fiber-metal (CHMF), have been particularly attractive for aerospace applications, due mainly to their high mechanical strength and stiffness associated with low density. These laminates (CHMF) consist of a sandwich structure consisting of layers of polymer composites and metal plates, stacked alternately. This setting allows you to combine the best mechanical performance of polymer composites reinforced with long fibers, to the high toughness of metals. Environmental effects should always be considered in the design of structural components, because these materials in applications are submitted to the effects of moisture in the atmosphere, the large cyclical variations of temperature around 82 ° C to -56 ° C, and high effort mechanical. The specimens of fibermetal composite were prepared at EMBRAER with titanium plates and laminates of carbon fiber/epoxy resin. This study aims to evaluate the effect of different environmental conditions (water immersion, hygrothermal chamber and thermal shock) of laminate hybrid titanium/carbon fiber/epoxy resin. The effects of conditioning were evaluated by interlaminar shear tests - ILSS, tensile, and vibration free