Detecção de áreas de oclusão para geração de ortoimagem verdadeira utilizando dados LASER

Pós-graduação em Ciências Cartográficas - FCT

Dinâmica não linear e projeto de controle em sistemas de transporte vertical: comportamentos periódicos e caóticos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The correlation between thermal comfort in buildings and fashion products

This article is about thermal comfort in the wearable product. The research correlates fashion and architecture, in so far as it elects the brise soleil - an architectural element capable of regulating temperature and ventilation inside buildings - as a study referential, in trying to transpose and adapt its mechanisms to the wearable apparel.

PCM thermal insulation in buildings

This paper presents the results of a numerical and experimental study of phase change material (PCM) filled walls and roofs under real operational conditions to achieve passive thermal comfort. The numerical part of the study was based on a one-dimensional model for the phase change problem controlled by pure conduction. Real radiation data was used to determine the external face temperature. The numerical treatment was based upon using finite difference approximations and the ADI scheme. The results obtained were compared with field measurements. The experimental set-up consisted of a small room with movable roof and side wall. The roof was constructed in the traditional way but with the phase change material enclosed. Thermocouples were distributed across the cross section of the roof. Another roof, identical but without the PCM, was also used during comparative tests. The movable wall was also constructed as is done traditionally but with the PCM enclosed. Again, thermocouples were distributed across the wall thickness to enable measurement of the local temperatures. Another wall, identical but without the PCM, was also used during comparative tests. The PCM used in the numerical and experimental tests was composed of a mixture of two commercial grades of glycol in order to obtain the required fusion temperature range. Comparison between the simulation results and the experiments indicated good agreement. Field tests also indicated that the PCM used was adequate and that the concept was effective in maintaining the indoor temperature very close to the established comfort limits. Further economical analysis indicated that the concept could effectively help in reducing the electric energy consumption and improving the energy demand pattern. © 1997 by John Wiley & Sons, Ltd.

Growth and yield analysis in different methods of beet (Cv. 'tall top early wonder') plantation

This objective of this study was to evaluate the effects of different methods of red beet seedling production and direct sowing on the development of the plant in field conditions. 'Tall Top Early Wonder' was used as the cultivar. The experimental design was a randomized blocks with 4 replications of each treatment: T1 - seedling produced in trays of 288 cells; T2 - 200 cells; T3 - 128 cells; T4 - 128 cells; T5 - direct sowing and T6 - bare-root seedling. The seedlings produced in trays and bare root seedlings were transplanted in the field 28 DAS with spacing of 0.20 x 0.10m. The mean height of plants, leaf area, leaf dry matter, petiole dry matter, shoot dry matter, root dry matter, relationship between shoot dry matter and root dry matter, absolute growth rate, relative growth rate, net assimilation rate, leaf area ratio and specific leaf area were determined. Storage root fresh matter and mean storage root diameter were determined starting from 77 DAS. Initial growth of the plants were superior for the direct sowing, resulting in smaller RGR and NAR than the other treatments. Independent of the production method, an increase of the cycle of the crop was verified. T6 had larger delay in the initial development. There was no difference for productivity. Method T1, had less expenses with respect to substrate and space in the vegetation home, without reduction in production.

Semi-automatic modeling of buildings from digital surface models

Semi-automatic building detection and extraction is a topic of growing interest due to its potential application in such areas as cadastral information systems, cartographic revision, and GIS. One of the existing strategies for building extraction is to use a digital surface model (DSM) represented by a cloud of known points on a visible surface, and comprising features such as trees or buildings. Conventional surface modeling using stereo-matching techniques has its drawbacks, the most obvious being the effect of building height on perspective, shadows, and occlusions. The laser scanner, a recently developed technological tool, can collect accurate DSMs with high spatial frequency. This paper presents a methodology for semi-automatic modeling of buildings which combines a region-growing algorithm with line-detection methods applied over the DSM.

Tall oil e seus subprodutos: alternativas como preservantes para madeira

Pós-graduação em Engenharia Mecânica - FEG

Analysis of the electrical characteristics and surge protection of EHV transmission lines supported by tall towers

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of Cracks Caused by Mechanical Vibrations in Buildings

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Detecção e restauração de áreas sombreadas em imagens digitais de alta resolução espacial

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Barriers to green buildings at two Brazilian engineering schools

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)