Short Implant to Support Maxillary Restorations: Bone Stress Analysis Using Regular and Switching Platform

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Cortical Bone Stress Distribution in Mandibles with Different Configurations Restored with Prefabricated Bar-Prosthesis Protocol: A Three-Dimensional Finite-Element Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Regular and Platform Switching: Bone Stress Analysis Varying Implant Type

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Micromechanics of dentin/adhesive interface in function of dentin depth: 3d finite element analysis

Objectives: The aim of this study was to analyze the stress distribution on dentin/adhesive interface (d/a) through a 3-D finite element analysis (FEA) varying the number and diameter of the dentin tubules orifice according to dentin depth, keeping hybrid layer (HL) thickness and TAǴs length constant. Materials and Methods: 3 models were built through the SolidWorks software: SD - specimen simulating superficial dentin (41 x 41 x 82 μm), with a 3 μm thick HL, a 17 μm length Tag, and 8 tubules with a 0.9 μm diameter restored with composite resin. MD - similar to M1 with 12 tubules with a 1.2 μm diameter, simulating medium dentin. DD - similar to M1 with 16 tubules with a 2.5 μm diameter, simulating deep dentin. Other two models were built in order to keep the diameter constant in 2.5 μm: MS - similar to SD with 8 tubules; and MM - similar to MD with 12 tubules. The boundary condition was applied to the base surface of each specimen. Tensile load (0.03N) was performed on the composite resin top surface. Stress field (maximum principal stress in tension - σMAX) was performed using Ansys Wokbench 10.0. Results: The peak of σMAX (MPa) were similar between SD (110) and MD (106), and higher for DD (134). The stress distribution pathway was similar for all models, starting from peritubular dentin to adhesive layer, intertubular dentin and hybrid layer. The peak of σMAX (MPa) for those structures was, respectively: 134 (DD), 56.9 (SD), 45.5 (DD), and 36.7 (MD). Conclusions: The number of dentin tubules had no influence in the σMAX at the dentin/adhesive interface. Peritubular and intertubular dentin showed higher stress with the bigger dentin tubules orifice condition. The σMAX in the hybrid layer and adhesive layer were going down from superficial dentin to deeper dentin. In a failure scenario, the hybrid layer in contact with peritubular dentin and adhesive layer is the first region for breaking the adhesion. © 2011 Nova Science Publishers, Inc.

Influence of the implant diameter with different sizes of hexagon: Analysis by 3-dimensional finite element method

The aim of this study was to evaluate the stress distribution in implants of regular platforms and of wide diameter with different sizes of hexagon by the 3-dimensional finite element method. We used simulated 3-dimensional models with the aid of Solidworks 2006 and Rhinoceros 4.0 software for the design of the implant and abutment and the InVesalius software for the design of the bone. Each model represented a block of bone from the mandibular molar region with an implant 10 mm in length and different diameters. Model A was an implant 3.75 mm/regular hexagon, model B was an implant 5.00 mm/regular hexagon, and model C was an implant 5.00 mm/ expanded hexagon. A load of 200 N was applied in the axial, lateral, and oblique directions. At implant, applying the load (axial, lateral, and oblique), the 3 models presented stress concentration at the threads in the cervical and middle regions, and the stress was higher for model A. At the abutment, models A and B showed a similar stress distribution, concentrated at the cervical and middle third; model C showed the highest stresses. On the cortical bone, the stress was concentrated at the cervical region for the 3 models and was higher for model A. In the trabecular bone, the stresses were less intense and concentrated around the implant body, and were more intense for model A. Among the models of wide diameter (models B and C), model B (implant 5.00 mm/regular hexagon) was more favorable with regard to distribution of stresses. Model A (implant 3.75 mm/regular hexagon) showed the largest areas and the most intense stress, and model B (implant 5.00 mm/regular hexagon) showed a more favorable stress distribution. The highest stresses were observed in the application of lateral load.

Avaliação da influência de diferentes materiais oclusais na confecção de próteses fixas implantossuportadas unitárias com diferentes diâmetros dos implantes osseointegrados: estudo pelo método dos elementos finitos tridimensionais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência da espessura da camada de cimento e da variação da temperatura no comportamento mecânico de fragmentos cerâmicos utilizados em restaurações estéticas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação da influência da angulação dos implantes com diferentes tipos de conexão protética na distribuição de tensões: estudo pelo método dos elementos finitos tridimensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da carga oclusal parafuncional em próteses implantossuportadas, variando-se a proporção coroa/implante e o sistema de conexão protética: estudo pelo método dos elementos finitos tridimensionais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Prótese protocolo com barra pré-fabricada: comportamento ósseo variando o tipo de osso e a configuração horizontal do arco mandibular no MEF-3D

Pós-graduação em Odontologia - FOA

Avaliação da influência da inclinação das cúspides e da direção das cargas oclusais na distribuição das tensões em próteses implanto-suportadas: estudo através do método dos elementos finitos tridimensionais

Pós-graduação em Odontologia - FOA

Avaliação da resistência à fratura e tensões em diferentes implantes e conexões protéticas: Análise in vitro e MEF-3D

Pós-graduação em Odontologia - FOA

Influência da altura da coroa em implantes osseointegrados: estudo pelo método dos elementos finitos tridimensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise das tensões em próteses unitárias implantossuportadas com diferentes tipos de conexões e qualidade óssea: estudo pelo método dos elementos finitos tridimensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sistemas adesivos convencional e autocondicionante: análise micromecânica tridimensional da interface dentina-adesivo

Pós-graduação em Odontologia - FOA