Distribution of the orchid species in the coastal plains of the fazenda beach, municipality of ubatuba, state of sao-paulo, brazil

A floristic survey for the family Orchidaceae was undertaken in a coastal forest area of ca. 8 km2 in the Picinguaba Development Center of the Serra do Mar State Park, in the municipality of Ubatuba, Brazil. The sampling used all tracks and roads of the area, up to the altitude of 50 m.s.m. and resulted in 77 species distributed in 45 genera. The spacial distribution of the species was plotted in maps of the nine physiognomical units identified for the area, based on 1:8.000 and 1:25.000 aerial photographs, and field observations. The results are shown in 1:10.000 topographic charts. Ninety percent of the species occur in at least 3 physiognomical units while 60% only occurred in a single unit, what indicates that the orchids can be used to characterize the vegetation even in large scales.

Reliability and failure modes of internal conical dental implant connections

Objective: Biological and mechanical implant-abutment connection complications and failures are still present in clinical practice, frequently compromising oral function. The purpose of this study was to evaluate the reliability and failure modes of anterior single-unit restorations in internal conical interface (ICI) implants using step-stress accelerated life testing (SSALT). Materials and methods: Forty-two ICI implants were distributed in two groups (n = 21 each): group AT-OsseoSpeed™ TX (Astra Tech, Waltham, MA, USA); group SV-Duocon System Line, Morse Taper (Signo Vinces Ltda., Campo Largo, PR, Brazil). The corresponding abutments were screwed to the implants and standardized maxillary central incisor metal crowns were cemented and subjected to SSALT in water. Use-level probability Weibull curves and reliability for a mission of 50,000 cycles at 200 N were calculated. Differences between groups were assessed by Kruskal-Wallis along with Bonferroni's post-hoc tests. Polarized-light and scanning electron microscopes were used for failure analyses. Results: The Beta (β) value derived from use level probability Weibull calculation was 1.62 (1.01-2.58) for group AT and 2.56 (1.76-3.74) for group SV, indicating that fatigue was an accelerating factor for failure of both groups. The reliability for group AT was 0.95 and for group SV was 0.88. Kruskal-Wallis along with Bonferroni's post-hoc tests showed no significant difference between the groups tested (P > 0.27). In all specimens of both groups, the chief failure mode was abutment fracture at the conical joint region and screw fracture at neck's region. Conclusions: Reliability was not different between investigated ICI connections supporting maxillary incisor crowns. Failure modes were similar. © 2012 John Wiley & Sons A/S.

Stress distribution in implant-supported prosthesis with external and internal implant-abutment connections

Objective. This study aimed to investigate the stress distribution in screwed implant-supported prostheses with different implant-abutment connections by using a photoelastic analysis. Materials and methods. Four photoelastic models were fabricated in PL-2 resin and divided according to the implant-abutment connection (external hexagon (EH) and Morse taper (MT) implants (3.75 × 11.5 mm)) and the number crowns (single and 3-unit piece). Models were positioned in a circular polariscope and 100-N axial and oblique (45) loading were applied in the occlusal surface of the crowns by using a universal testing machine. The stresses were photographically recorded and qualitatively analyzed using software (Adobe Photoshop). Results. Under axial loading, the MT implants exhibited a lower number of fringes for single-unit crowns than EH implants, whereas for a 3-unit piece the MT implants showed a higher number of fringes vs EH implants. The oblique loading increased the number of fringes for all groups. Conclusion. In conclusion, the MT implant-abutment connection reduced the amount of stress in single-unit crowns, for 3-unit piece crowns the amount of stress was lower using an external hexagon connection. The stress pattern was similar for all groups. Oblique loading promoted a higher stress concentration than axial loading. © Informa Healthcare.

Dinâmica espaço-temporal de danos do cancro basal em Eucalyptus grandis

Pós-graduação em Agronomia (Proteção de Plantas) - FCA

Plataforma regular versus switching: estudo mecânico por meio de testes laboratoriais de fadiga e análise de elementos finitos em implantes com hexágono externo e interno

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Mechanical Evaluation of Four Narrow-Diameter Implant Systems

Purpose: This study aimed to evaluate the survival probability of four narrow-diameter implant systems when subjected to fatigue loading. Materials and Methods: Seventy-two narrow-diameter implants to be restored with single-unit crowns were divided into four groups (n = 18): Astra Tech (3.5-mm diameter), with a standard connection (ASC); BioHorizon (3.4-mm diameter), with a standard connection (BSC); Intra-Lock (3.4-mm diameter), with a standard multilobular connection (ISC); and Intra-Lock (3.4-diameter), with a modified square connection (IMC). The corresponding abutments were screwed onto the implants, and standardized metal crowns (maxillary central incisors) were cemented and subjected to step-stress accelerated life testing in water. Use-level probability Weibull curves and reliability for 100,000 cycles at 150 and 200 N (90% two-sided confidence intervals) were calculated. Polarized light and scanning electron microscopes were used to access the failure modes. Results: The calculated survival probability for 100,000 cycles at 150 N was approximately 93% in group ASC, 98% in group BSC, 94% in group ISC, and 99% in group IMC. At 200 N, the survival rate was estimated to be approximately < 0.1% for ASC, 77% for BSC, 34% for ISC, and 93% for IMC. Abutment screw fracture was the main failure mode for all groups. Conclusions: Although the probability of survival was not significantly different among systems at a load of 150 N, a significant decrease was observed at 200 N for all groups except IMC.

Remoção de matéria orgânica e nitrogênio de efluentes provenientes de abatedouros de bovinos por meio de reator aeróbio operando em bateladas sequenciais com adição de coagulante químico

The volume of liquid effluent generated in cattle slaughterhouses is quite high and cannot be released untreated in water bodies due to its high pollution load of predominantly organic origin. To minimize the environmental impacts of its industrial wastewater and meet the local environmental legislation, abattoirs shall make the treatment of these effluents. The present work aims to develop the study of a reactor by sequential batch pilot scale, in order to optimize their performance in treating wastewater from a cattle slaughterhouse. The treatment system used was developed and installed in the Laboratory of Wastewater Treatment, in Faculty of Science and Technology UNESP, Presidente Prudente campus. The procedure used followed the operation of sequential batch reactors, in which all processes and treatment operations occurring sequentially in a single unit, by establishing specific operating cycles, which comprise the following separated phases: aerobic reaction, anoxic reaction, sedimentation and emptying. Aiming to improve the quality of treatment was planned the addition of coagulant Poly Aluminum Chloride (PAC) in the reactor, by determining their optimal dosage by Jar-test trials. Were prepared four steps with specific operating cycles: step one or acclimatization (10 hour of aeration, one hour and 30 minutes of sedimentation and 30 minutes for exchanging the effluent); step 2 (6 hours of aeration or aerobic phase, 4 hours and 45 minutes of stirring or anoxic phase and 1 hour and 15 minutes for sedimentation and exchange effluent); step 3 (2 hours and 30 minutes of aeration, 8 hours and 15 minutes of stirring and 1 hour and 15 minutes for sedimentation and exchange) and step 4 (2 hours of aeration, 8 hours and 45 minutes of stirring and 1 hour and 15 minutes for sedimentation and exchange)... (Complete abstract click electronic access below)

Analysis of the biomechanical behavior of short implants: the photo-elasticity method

The aim of this study was to analyze the stress distribution of short implants supporting single unit or splinted crowns by the photo-elasticity method. Four photo-elastic models were produced: A (3.75×7mm); B (3.75×7mm, 3.75×7mm and 3.75×7mm); C (3.75×10mm, 3.75×7mm and 3.75×7mm); D (3.75×13mm, 3.75×7mm and 3.75×7mm). The prostheses were made with Ni-Cr alloy. A load of 100N in the axial and oblique directions was applied, totaling 380 applications, individually capturing their images in each model. The data were randomized and analyzed qualitatively and quantitatively by 2 examiners. The oblique loading was significantly more damaging. The increase in length was favorable for stress distribution (p<0.05). The splinting was beneficial for the transmission of stresses mainly (p<0.05). The splinting of the crowns, as well as increasing the length of the first implant and axial loading was most beneficial in the stress distribution. Short splinted implants behaved better than single unit implants. Increasing of the length of the first implant significantly improved the stress distribution in all analyzed situations.

Análise da distribuição de tensões em reabilitação com implantes cone morse em maxilar posterior: estudo pelo MEF 3D não linear

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Detection of mixed microbial biofilms on central venous catheters removed from Intensive care Unit Patients

Cateteres venosos centrais inseridos em pacientes internados em unidade de terapia intensiva foram avaliados por métodos microbiológicos (cultura semi-quantitativa) e microscopia eletrônica de varredura a fim de detectar adesão microbiana e correlacionar com a cultura de sangue. Durante o período de estudo, foram avaliados 59 pacientes com cateter venoso central. A idade dos pacientes, sexo, sítio de inserção e tempo de permanência do cateter foram anotados. O cateter era de poliuretano não tunelizado e de único lúmen. O sangue para cultura foi coletado no momento da remoção do cateter. de 63 pontas de cateteres, 30 (47,6%) foram colonizadas e a infecção encontrada em 5 (23,8%) cateteres. A infecção foi mais prevalente em 26 pacientes (41,3%) com cateteres inseridos em veia subclávia do que nos 3 (3,2%) inseridos em veia jugular. A infecção foi observada com mais freqüência em cateteres com tempo de permanência maior do que sete dias. Os microrganismos isolados incluíram 32 estafilococos coagulase-negativa (29,7%), 61 bactérias Gram-negativas (52,9%), 9 estafilcocos coagulase-positiva (8,3%) e 3 leveduras (2,7%). Como agentes causais de infecções em unidade de terapia intensiva foram isolados E. aerogenes, P. aeruginosa, A. baumannii. Os antimicrobianos com maior atividade in vitro contra as bactérias Gram-negativas foram o imipenem e contra as Gram-positivas vancomicina, cefepime, penicilina, rifampicina e tetraciclina. As análises por microscopia eletrônica de varredura revelaram biofilmes sobre a superfície de todos os cateteres examinados.

Peritoneal Dialysis-Related Peritonitis Due to Staphylococcus aureus: A Single-Center Experience over 15 Years

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Photoelastic Analysis of Biomechanical Behavior of Single and Multiple Fixed Partial Prostheses With Different Prosthetic Connections

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Distribution transformers modeling with angular displacement: actual values and per unit analysis

In this work a detailed modeling of three-phase distribution transformers aimed at complementing well-known approaches is presented. Thus, incidence of angular displacement and tapping is taken into account in the proposed models, considering both actual values and per unit. The analysis is based on minimal data requirement: solely short-circuit admittance is needed since three-phase transformers are treated as non-magnetically-coupled single-phase transformers. In order to support the proposed methodology, results obtained through laboratory tests are presented.

Single walled MgF2 nanotubes

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The Bauru Group: A continental Cretaceous unit in Brazil - Concepts based on micropaleontological, oxygen isotope and stratigraphical data

The integration of outcrop and subsurface information, including micropaleontological data, facies and sequence stratigraphic studies, and oxygen isotope analysis, allow us to present a new stratigraphic model for the Cretaceous continental deposits of the Bauru Group, Brazil. Thirty-eight fossil taxa were recovered from these deposits, including 29 species of ostracodes and 9 species of charophytes. Seven of these ostracode species and three subspecies are new and formally described here. The associations of Chara barbosai - Ilyocypris cf. riograndensis, found in the Adamantina Formation, and Amblyochara sp. - Neuquenocypris minor mineira nov. subsp., found in the Marília Formation. Ponte Alta Member, represent two distinct groups that are respectively Turonian-Santonian and Maastrichtian (probably Late Maastrichtian) in age. Therefore, a hiatus, encompassing more than 11 Ma, separates those two formations. From bottom to top, four depositional cycles were recognized in the Bauru Group in western São Paulo: cycles 1 and 2 belong to Caiuá Formation (fluvio-lacustrine and lacustrine deposits in the Presidente Prudente region), cycle 3 to the Santo Anastácio and lower Adamantina Formation (respectively fluvial and lacustrine deposits), and cycle 4 to the upper Adamantina Formation (fluvio-lacustrine facies). An erosional unconformity separates the Caiuá and Santo Anastácio Formations (between cycles 2 and 3). The Marília Formation is a distinct unit from the underlying succession; it does not occur in western São Paulo, but is found in restricted areas of São Paulo, Minas Gerais, Mato Grosso do Sul and Goiás States. During the deposition of the Bauru Group (Aptian? to Maastrichtian) the climate was hot and arid-semiarid. Shallow lakes underwent fluctuations in expansion (wet phases) and contraction (dry phases), as well as variations in salinity. During the deposition of the Adamantina Formation (Turonian-Santonian) there were long, dry periods that caused segmentation of large lakes (due to topographic irregularities in the basaltic substrate) and sometimes exposures of the lake floors; when flooded these lake floors were colonized by extensive meadows of single species of charophytes. Small ephemeral ponds, that were hydrochemically unstable and colonized by multiple species of charophytes, were the depositional sites for the marls and mudstones of Ponte Alta Member (Maastrichtian, Late Maastrichtian?). Our micropaleontological age control, combined with the Late Cretaceous ages of volcanic ashes found in the southeastern Brazil coastal basins, and the stratigraphic position of analcimites from the Jaboticabal-SP region, suggest a Late Coniacian-Santonian age for important magmatic events occurred in the interior of Brazil (north-central São Paulo State, Triângulo Mineiro, and southwestern Goiás State).