THE INFLUENCE of SHORT-HEATING-CYCLE INVESTMENTS on THE QUALITY of COMMERCIALLY PURE TITANIUM CASTINGS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Biocompatibility of denture base acrylic resins evaluated M culture of L929 cells. Effect of polymerisation cycle and postpoymerisation treatments

Objective: the purpose of this study was to evaluate the effect of two post-polymerisation treatments and different cycles of polymerisation on the cytotoxicity of two denture base resins.Materials and methods: the resins tested were Lucitone 550 and QC 20. Discs of resins were fabricated following the manufacturer's instructions. Lucitone 550 was processed by long cycle or short cycle. The resin QC 20 was processed by reverse cycle or normal cycle. The specimens were divided into groups: (i) post-polymerised in microwave for 3 min at 500 W; (ii) post-polymerised in water-bath at 55 degrees C for 60 min and (iii) without post-polymerisation. Eluates were prepared by placing three discs into a sterile glass vial with 9 ml of Eagle's medium and incubated at 37 degrees C for 24 hours. L929 cells were seeded into 96 3 well culture plates and DNA synthesis was assessed by H-thymidine incorporation assay.Results: the results were submitted to two-way ANOVA and Tukey HSD test. QC 20 specimens polymerised by the normal cycle and submitted to microwave post-polymerisation were graded as moderately cytotoxic. Similar results were observed for Lucitone 550 processed by long cycle without post-polymerisation. The other experimental groups were graded as not cytotoxic. After water-bath post-polymerisation, specimens of Lucitone 550 processed by long cycle produced significantly lower inhibition of DNA synthesis than the other groups.Conclusion: the long cycle increased the cytotoxicity of Lucitone 550 and water-bath post-polymerisation reduced the cytotoxicity of Lucitone 550 processed by long cycle.

Folha diagnótica para avaliação do estado nutricional do feijoeiro

The bean is a nutrient demanding plant, either due to the small and shallow root system or due to the short cycle. A study with doses of lime and boron was conducted and correlations were made between two types of leaf (+ 1 and + 3) of the bean with the contents of these elements in plants and production, aiming to establish the most appropriate leaf for diagnosis of nutritional status. The experiment was conducted in greenhouse conditions employing bean seeds cv. BRS Talisma. Lime rates considering the saturation of bases (70%), were calculated as zero, half the standard dose, dose to increase V = 70% (default), one and a half and twice the standard dose, while the boron amounts used were: zero, 0.6, 1.2, 1.8 and 2.4 mg B dm(-3). At the time of flowering, diagnostic leaves + 1 and + 3 (mature leaves from the apex) were collected along with sampling of a plant (aerial part) per pot and the measurement of production. Through correlations it was verified that nutrients, calcium, magnesium and boron in the leaf + 3 showed higher correlation coefficients with levels in the plant and production data.

Comportamento de algumas leguminosas em distintas épocas de semeadura

Estudou-se, através do presente trabalho, o efeito de épocas de semeadura sobre o comportamento de diversas leguminosas, comumente utilizadas na prática da adubação verde. O delineamento experimental usado no campo foi o inteiramente casualizado, em esquema de parcelas subdivididas com 40 tratamentos, constituídos pela combinação de 10 leguminosas com 4 épocas de semeadura. Os resultados obtidos indicaram que para todas as leguminosas avaliadas, as épocas de semeadura influenciaram a produção de matéria seca total, sobressaindo a mucuna preta (Stizolobiun aterrimum) na semeadura de janeiro e o guandu (Cajanus cajan) cv. FAJ e cv. Paraíba na semeadura de outubro. A mucuna preta constituiu-se na melhor opção para rotação com culturas de verão de ciclo curto.

Colored polyethylene soil covers and grafting effects on cucumber flowering and yield

O pepino (Cucumis sativus L.) é, dentre os produtos hortícolas, um dos mais visados para o cultivo em estufas no Brasil devido ao ciclo vegetativo curto e ao elevado valor econômico no período da entressafra. Estudou-se, em condições de ambiente protegido, a influência de diferentes cores de cobertura plástica de solo no florescimento e na produção de pepino híbrido 'Yoshinari' enxertado ou não sobre abóbora híbrida 'Ikky'. Os tratamentos de cobertura foram: preto, preto pintado de branco, verde, e sem cobertura. Os tratamentos cobertos com plástico e sem enxertia apresentaram florescimento com distribuição mais uniforme na planta. O número de flores foi superior no tratamento preto/branco enxertado. Para as plantas não enxertadas, todas as coberturas favoreceram o florescimento. A enxertia favoreceu o florescimento somente para os tratamentos com plástico preto ou verde. A fixação dos frutos aumentou pelo uso de cobertura plástica, mas a enxertia não teve influência. A distribuição uniforme do florescimento manteve-se na frutificação apenas para os tratamentos com plantas enxertadas e cobertura do solo com plástico preto ou verde. Tanto o uso de cobertura plástica quanto a enxertia favoreceram a colheita precoce. Os frutos de melhor qualidade e as maiores produções, em número de frutos, foram obtidos nos tratamentos preto e preto/branco, não enxertados. A enxertia 'Yoshinari'/'Ikky' provocou o aparecimento de frutos mais grossos e menores, fora do padrão de comercialização.

Doses e épocas de aplicação de nitrogênio em cobertura na cultura do painço (Panicum miliaceum L.)

A cultura do painço é uma opção interessante tanto para a formação de palha para cobertura do solo como para a produção de grãos, pelo seu rápido crescimento, tolerância à seca e ciclo curto. No entanto, são escassas as informações sobre o manejo da adubação nitrogenada para essa cultura. Objetivou-se, neste estudo, avaliar o efeito de doses e épocas de aplicação de nitrogênio em cobertura nas características agronômicas e produtividade de grãos do painço. O delineamento experimental foi o de blocos ao acaso, em esquema fatorial 4x2, constituído pela combinação de quatro doses (0, 30, 60 e 120 kg ha-1 de N) e duas épocas de aplicação (14 e 28 dias após a emergência - DAE) do fertilizante nitrogenado (uréia) em cobertura, com quatro repetições. A adubação nitrogenada em cobertura promoveu aumento na altura da planta, comprimento da panícula e produtividade de grãos da cultura do painço, independentemente da época de aplicação. O número de grãos por panícula foi incrementado pela adubação nitrogenada apenas com a aplicação que foi realizada aos 14 DAE. A aplicação de N em cobertura, aos 14 dias após a emergência, proporcionou acréscimos nas características agronômicas, até a dose de 120 kg ha-1 (maior dose), acarretando aumento da produtividade de grãos do painço.

Electrically, Chemically, and Photonically Powered Torsional and Tensile Actuation of Hybrid Carbon Nanotube Yarn Muscles

Artificial muscles are of practical interest, but few types have been commercially exploited. Typical problems include slow response, low strain and force generation, short cycle life, use of electrolytes, and low energy efficiency. We have designed guest-filled, twist-spun carbon nanotube yarns as electrolyte-free muscles that provide fast, high-force, large-stroke torsional and tensile actuation. More than a million torsional and tensile actuation cycles are demonstrated, wherein a muscle spins a rotor at an average 11,500 revolutions/minute or delivers 3% tensile contraction at 1200 cycles/minute. Electrical, chemical, or photonic excitation of hybrid yarns changes guest dimensions and generates torsional rotation and contraction of the yarn host. Demonstrations include torsional motors, contractile muscles, and sensors that capture the energy of the sensing process to mechanically actuate.

Flexural strength of acrylic resins polymerized by different cycles

Despite the large number of studies addressing the effect of microwave polymerization on the properties of acrylic resin, this method has received limited clinical acceptance. This study evaluated the influence of microwave polymerization on the flexural strength of a denture base resin. A conventional heat-polymerized (Classico), a microwave-polymerized (Onda-Cryl) and a autopolymerizing acrylic (Jet) resins were used. Five groups were established, according to polymerization cycles: A, B and C (Onda-Cryl, short cycle - 500W/3 min, long - 90W/13 min + 500W/90 see, and manufacturing microwave cycle - 320W/3 min + OW/3 min + 720W/3 min); T(Classico, water bath cycle - 74 degrees C/9h) and Q (Jet, press chamber cycle - 50 degrees C/15 min at 2 bar). Ten specimens (65 x 10 x 3.3 mm) were prepared for each cycle. The flexural strength of the five groups was measured using a three-point bending test at a cross-head speed of 5 mm/min. Flexural strength values were analyzed by one-way ANOVA and the Tukey's test was performed to identify the groups that were significantly different at 5% level. The microwave-polymerized groups showed the highest means (p<0.05) for flexural strength (MPa) (A = 106.97 +/- 5.31; B = 107.57 +/- 3.99; C = 109.63 +/- 5.19), and there were no significant differences among them. The heat-polymerized group (T) showed the lowest flexural strength means (84.40 +/- 1.68), and differ significantly from all groups. The specimens of a microwavable denture base resin could be polymerized by different microwave cycles without risk of decreasing the flexural strength.

Effect of a post-polymerization treatments on the flexural strength and vickers hardness of reline and acrylic denture base resins

This study evaluated the effect of water-bath and microwave post-polymerization treatments on the flexural strength and Vickers hardness of four autopolymerizing reline resins (Duraliner II-D, Kooliner-K, Tokuso Rebase Fast-TR and Ufi Gel Hard C-UGH) and one heat-polymerized acrylic resin (Lucitone 550-L), processed using two polymerization cycles (short cycle - 90 minutes at 73°C and 100°C for 30 minutes; and long cycle - 9 hours at 71°C). For each material, thirty specimens (64 x 10 x 3.3 mm) were made and divided into 3 groups (n=10). Specimens were tested after: processing (control group); water-bath at 55°C for 10 minutes (reline materials) or 60 minutes (L); and microwave irradiation. Flexural strength tests were performed at a crosshead speed of 5 mm/min using a three-point bending device with a span of 50 mm. The flexural strengths values were calculated in MPa. One fragment of each specimen was submitted to Vickers hardness test. Data were analyzed by 2-way ANOVA followed by Tukey's HSD test (α=0.05). L microwaved specimens (short cycle) exhibited significantly higher flexural strength means than its respective control group (p<0.05). Water-bath promoted a significant increase (p<0.05) in flexural strength of K and L (long cycle). The hardness of the tested materials was not influenced by the post-polymerization treatments. Post-polymerization treatments could be used to improve the flexural strength of some materials tested.

Plantas de cobertura em pré-safra e aplicação de nitrogênio na cultura do milho

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)