Estudo sobre a resistencia aos antimicrobianos em bacterias isoladas de pacientes hospitalizados (Botucatu, 1988-1992)

Since 1988 to 1992, a study about susceptibility to antimicrobial drugs of bacterias isolated from hospitalized patients was performed. The compared susceptibility to important drugs (ampicillin, cephalotin, cefoxitin, ceftaxizime, ceftriaxone, aztreonam, gentamicin, amikacin, pefloxacin, ciprofloxacin, imipenem, oxacillin and vancomycin) was investigated in 1200 strains (300 of each specie) of the prevalent bacterias: E. coli, Klebsiella pneumoniae, Pseudomonas aeruginosa and S. aureus. Minimal inhibitory concentration (MIC) was determined by agar dilution method, using from 0.05 to 256 mcg of each drug per ml of culture medium (Mueller-Hinton). Ranges of MIC, MIC(50%), MIC(90%) and the proportion of resistant strains were determined and permitted to know the 4 drugs that were found to be more active against bacterias; the CIM(90%) values are: E. coli - aztreonam (0.1 mcg/ml), pefloxacin (0.1), ceftazidime (0.25) and ceftriaxone (0.05); K. pneumoniae-aztreonam (0.25) ceftriaxone (0.25), ceftazidime (0.5) and pefloxacin (2.0); P. aeruginosa-imipenem (4.0), aztreonam (16), ceftazidime (16) and ciprofloxacin (16); S. aureus-vancomycin (1.01, ciprofloxacin (8, 0), amikacin (128) and cephalothin (128 mg/ml). The better 'in vitro' antibacterial activity observed was related to: aztreonam (77-100% of the sensitive strains), ceftazidime (50-99,7%), pefloxacin (73-99,7%), ciprofloxacin (80%), imipenem (93%) and vancomycin (100%).

Efecto del blanqueamiento dental con peroxido de hidrógeno al 35% en la resistencia de unión de dientes restaurados con resina compuesta

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influencia de diferentes intensidades de luz en la resistencia de unión de un sistema adhesivo utilizando un colorante fluorescente para su observación

The purpose of this study was to use a fluorescent dye and CLSM microscope to observe the effect of different light intensities on dentin tensile bond strength. Flat dentin surfaces were created on 16 intact human third molars and divided in 4 groups: Group G1 - halogen - KM -200R®; Group G2 - LED - Ultraled®; Group G3 - LED - UltraLume LED5® and Group G4 - LED - Biolux Single V®. For all the groups, the restoration procedure used Single Bond® adhesive, mixed with rodamin B and InTen-S® composite resin. Then, they were cut on serial sections to obtain 1 mm2 area and submitted to micro tensile test and after words, the fractures were analyzed with a digital microscope and CLSM. The statistical analysis showed that all in all groups, except Group G2, which had a significant smaller tensile bond strength ratio. The fracture mode analysis showed that there were significant differences when comparing groups G1 / G2, and G2 / G4. There is no evidence of relevant differences among the other groups. With these results, we conclude that the use of fluorescent dye and CLSM demonstrated to be a simple and nondestructive technique, and that there are evidences that light intensities influenced the dentine tensile.

Avaliação de um sensor de resistencia eletrica e sua correlação com atributos do solo

The electrical measures of the soil have been used as variables that correlate with its characteristics. This study aimed at developing an electrical capacitance sensor of low cost, to evaluate its performance on the field and verify the correlation between the measurements of electrical capacitance with physical properties (sand, silt and clay) and chemical properties of soil (pH, MO, P resin, H + Al, K, Ca, Mg, SB, CTC and V%) and the moisture content. The data sampling was performed at the farm named "Capão da Onça" which belongs to the State University of Ponta Grossa. The samples collection was conducted in an area of approximately 13 hectares, totalizing 81 samples. In each sampling the electrical capacitance of the soil was measured. After the sensor withdrawal, soil samples were collected and sent to be analysed in the laboratory of the College of Agronomics Science of the Paulista State University. The measuring instrument used to collect data on electric capacitance of the soil a digital multimeter was used. The data were submitted to the analysis of correlation and regression. The developed system presented a low cost and it was capable to measuring variation of the electrical capacitance of the soil. The obtained measures satisfactorily correlated with the levels of clay and sand, and weakly with the moisture content. This had demonstrated the possibility to use a sensor to verify the soil texture in not homogeneous areas. The measures of the electrical capacitance of the soil obtained by the sensor had significantly correlated with the soil attributes: calcium, magnesium, pH, SB and CTC. These results had demonstrated the possibility to use a sensor for soil fertility control.