Optimization procedures in the design of continuous induction hardening and tempering installations for magnetic steel bars

An inverse problem concerning the industrial process of steel bars hardening and tempering is considered. The associated optimization problem is formulated in terms of membership functions and, for the sake of comparison, also in terms of quadratic residuals; both geometric and electromagnetic design variables have been considered. The numerical solution is achieved by coupling a finite difference procedure for the calculation of the electromagnetic and thermal fields to a deterministic strategy of minimization based on modified Flctcher and Reeves method. © 1998 IEEE.

Planejamento de experimentos em blocos aplicado às propriedades mecânicas de arames de aço para molas

The purpose of this article is to demonstrate an application of the design of block experiments via analysis and multiple linear regression in the investigation of a steel thermal treatment process with multiple responses. The study aimed to design statistical models to predict the mechanical properties in SAE 9254 draw steel wires, with diameters of 2.00 mm and 6.50 mm, after quench hardening and tempering. For this purpose, process input variables (wire diameter, processing speed, tempering temperature and polymer concentration) were investigated regarding their influence on the material tensile strength, yield point and hardness. The results revealed that the mechanical properties of the steel wire are significantly influenced by the selected variables, and analysis of variance (ANOVA) was employed to validate the design of the statistical models. Multiple linear regression allowed for an appropriate representation of the process, and graphical analysis was found to be very useful in displaying the behavior of the multiple responses.

Modelagem e otimização por metodologia de superfícies de resposta: um estudo em arames de aço SAE 9254 para molas automobilísticas

Pós-graduação em Engenharia Mecânica - FEG

Projeto de experimentos e modelamento matemático do limite de resistência dos arames de aço SAE 9254 temperados e revenidos usados na fabricação de molas automobilísticas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effects of fetuin on zona pellucida hardening, fertilization and embryo development in cattle

Mammalian oocytes can undergo spontaneous meiotic maturation when they are liberated from their follicles and cultured in vitro; however, the zona pellucida (ZP) becomes resistant to chymotrypsin digestion, or hardens, when spontaneous maturation occurs in serum-free medium. Schroeder et al. [Biol. Reprod. 43 (1990) 891] described that fetuin, a component of fetal calf serum (FCS), inhibits ZP hardening during oocyte maturation. The aim of this experiment was to study the effect of the presence of cumulus cells and addition of hormones to maturation media on bovine zona hardening and embryo development in medium with and without fetuin. In Experiment 1, different concentrations of fetuin were added to the maturation medium. The time necessary for digestion of 50% of the ZP (d50) was not different when oocytes were matured in presence of 10% FCS, 1 mg/ml polyvinyl alcohol (PVA), or 4, 1 and 0.25 mg/ml of fetuin; cleavage rates were also similar. However, significantly more blastocysts (P < 0.05) were formed when FCS was used compared to PVA and 0.25 mg/ml of fetuin. In Experiment 11, we examined the influence of the presence of cumulus cells and hormones during the maturation of oocytes in media with PVA, BSA, FCS and fetuin. The d50 was significantly higher (P < 0.05) when oocytes were matured in presence of cumulus cells. The cleavage rate of cumulus-intact oocytes was similar for all groups. However, when oocytes were partially stripped before maturation, the cleavage rate was significantly higher (P < 0.05) when FCS or fetuin was used. In both stripped and non-stripped groups, significantly more blastocysts (P < 0.05) were formed when oocytes were matured with FCS compared to BSA and PVA. These results indicate that zona hardening, as described for mouse and human oocytes, does not have a large effect on bovine cumulus-intact oocytes. Apparently fetuin can be used as a substitute for FCS during bovine oocyte maturation, since it leads to similar developmental rates as FCS in intact and partially stripped oocytes. (C) 2002 Published by Elsevier B.V. B.V.

Desenvolvimento de tubo ARBL contendo 1Cr 0,2Mo fabricado pelo processo ERW/HF destinado à indústria de petróleo e gás

Pós-graduação em Engenharia Mecânica - FEG

Microstructure evolution during warm deformation of low carbon steel with dispersed cementite

The microstructure evolution and mechanical behavior during large strain of a 0.16%C-Mn steel has been investigated by warm torsion tests. These experiments were carried out at 685°C at equivalent strain rate of 0.1 s . The initial microstructure composed of a martensite matrix with uniformly dispersed fine cementite particles was attained by quenching and tempering. The microstructure evolution during tempering and straining was performed through interrupted tests. As the material was reheated to testing temperature, well-defined cell structure was created and subgrains within lath martensite were observed by TEM; strong recovery took place, decreasing the dislocation density. After 1 hour at the test temperature and without straining, EBSD technique showed the formation of new grains. The flow stress curves measured had a peculiar shape: rapid work hardening to a hump, followed by an extensive flow-softening region. 65% of the boundaries observed in the sample strained to ε = 1.0 were high angle grain boundaries. After straining to ε = 5.0, average ferrite grain size close to 1.5 μm was found, suggesting that dynamic recrystallization took place. Also, two sets of cementite particles were observed: large particles aligned with straining direction and smaller particles more uniformly dispersed. The fragmentation or grain subdivision that occurred during reheating and tempering time was essential for the formation of ultrafine grained microstructure.

Caracterização de um aço microligado ao boro e tratado termicamente utilizado na fabricação de tubos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

On the performance of a dual-mode non-linear vibration energy harvesting device

The research trend for harvesting energy from the ambient vibration sources has moved from using a linear resonant generator to a non-linear generator in order to improve on the performance of a linear generator; for example, the relatively small bandwidth, intolerance to mistune and the suitability of the device for low-frequency applications. This article presents experimental results to illustrate the dynamic behaviour of a dual-mode non-linear energy-harvesting device operating in hardening and bi-stable modes under harmonic excitation. The device is able to change from one mode to another by altering the negative magnetic stiffness by adjusting the separation gap between the magnets and the iron core. Results for the device operating in both modes are presented. They show that there is a larger bandwidth for the device operating in the hardening mode compared to the equivalent linear device. However, the maximum power transfer theory is less applicable for the hardening mode due to occurrence of the maximum power at different frequencies, which depends on the non-linearity and the damping in the system. The results for the bi-stable mode show that the device is insensitive to a range of excitation frequencies depending upon the input level, damping and non-linearity.

Influence of silver additions on the aging characteristics of the Cu-10.4at.%Al alloy

The influence of additions of 1.3, 2.5, 3.8, 5.1, and 6.3 at.% Ag on the aging behavior of the Cu-10.4at.%Al alloy was studied using microhardness measurements, scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analysis. The results indicated that with silver additions it is possible to obtain a response to age hardening, and that for large aging times there is a decrease in the alloy hardness, with a process that leads to Ag and Al segregation. © 1998 Elsevier Science S.A.

Avaliação de quatro métodos de restauração florestal de áreas úmidas degradadas no Município de Mineiros do Tietê - SP

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Uma análise da dinâmica do pêndulo eletromecânico utilizando a teoria de pertubações

Pós-graduação em Matemática - IBILCE

Determinação da taxa de propagação de trinca por fadiga dos aços SAE-1050 e SAE-4130 empregados na fabricação de eixos ferroviários

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do efeito springback em aços avançados de alta resistência aplicados a indústria automobilística

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do comportamento mecânico e microestrutural de um aço maraging após soldagem a laser e tratamentos térmicos

Pós-graduação em Engenharia Mecânica - FEG