The use of slot filter in piezocone tests for site characterization of tropical soils

The use of piezocone tests with a slot filter filled with automotive grease for site characterization of tropical soils is assessed. Laboratory tests using the slot filter filled with automotive grease as well as the conventional porous piezo-element saturated with glycerin were carried out to evaluate the pore pressure (u 2) transducer response. CPTu tests using piezo-elements saturated with glycerin and the slot filter filled with grease were pushed side by side in different research sites in Brazil. Estimates of mechanical and hydraulic soil parameters were made based on pore pressure dissipation curves from using both techniques. Laboratory test results indicate that the pore pressure response using the slot filter with grease was delayed when compared to the piezo-element saturated with glycerin, since grease has a higher viscosity. For tropical soils, the records of u2 in piezocone tests using slot filter with grease presented larger peaks than with porous element saturated with glycerin. Records of u2 using the slot filter above the groundwater table suggest the increase of the degree of saturation in unsaturated zone, where porous filter can be desaturated by suction. The slot filter can be used to help the interpretation of the soil profile with deep groundwater level as well as to help detecting its position for some studied soils. The results shown high repeatability for all study sites. This technique is much easier to handle, especially for tropical soils, where the groundwater table is usually deep and pre-drilling is expensive and time consuming. © 2009 IOS Press.

Comparison of four trap types for ambrosia beetles (Coleoptera, Scolytidae) in Brazilian Eucalyptus stands

Eucalyptus spp. plantations represent >60% of the reforested area in Brazil. Although ambrosia beetle attacks on live trees were at first nonexistent, they have begun to appear with greater frequency. Monitoring for pest insects is a key factor in integrated pest management, and baited traps are one of the most widely used methods for insect population detection and survey. We compared the efficiency of the most widely used trap in Brazil to survey for ambrosia beetles and other Scolytidae, the ESALQ-84 type, with other traditionally employed traps: the multiple funnel (Lindgren trap); drainpipe; and slot (Theyson) traps, in a Eucalyptus grandis Hill ex Maiden stand in Brazil. The ESALQ-84 trap was the most efficient in trapping Hypothenemus eruditus Westwood and Hypothenemus obscurus (F.); the multiple funnel trap caught significantly more Cryptocarenus diadematus Eggers; whereas the slot trap caught more Premnobius cavipennis Eichhoff and Xyleborus affinis Eichhoff than the other traps. The drainpipe trap was the least effective trap overall. When corrected for number of beetles caught per trap surface area, catches were significantly higher on the ESALQ-84 trap for the majority of the species analyzed, probably because of a smaller trap surface area. The slot trap was recommended for it caught overall more beetles of the three most economically important scolytid species in eucalypt plantations in Brazil, P. cavipennis, X. affinis, and X, ferrugineus.

Implantes de resina de poliuretana vegetal (Ricinus communis) na tração linear, fixação e fusão vertebral no cão: estudo experimental

Placa e espaçador de polímero derivado do óleo de mamona (PDOM) (Ricinus communis) foram avaliados clínica, radiográfica e histologicamente na tração linear, fixação e fusão vertebral cervical em 20 cães adultos, sem raça definida, pesando entre 17 e 22kg. Foram sacrificados quatro animais aos 10, 30, 60, 90 e 120 dias de pós-operatório. Após exposição da coluna cervical, por acesso ventral, o disco intervertebral de C4-C5 foi fenestrado e a abordagem ao canal medular foi feita por meio de fenda óssea. Um espaçador de PDOM foi colocado preenchendo o defeito ósseo. Os corpos vertebrais C4-C5 foram fixados com placa do mesmo material, utilizando-se dois parafusos corticais em cada corpo vertebral. Apenas um animal apresentou déficit neurológico no pós-operatório imediato. Radiograficamente as vértebras mostravam-se normais e alinhadas, sem colapso do espaço intervertebral, porém não houve neoformação óssea entre as vértebras. Ao exame mielográfico, não houve compressão da medula espinhal. Os implantes foram efetivos em manter a tração linear e fixação das vértebras cervicais e não ocorreu a fusão vertebral.

Platelet-rich plasma stimulates cytokine expression and alkaline phosphatase activity in osteoblast-derived osteosarcoma cells

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of light-curing units on microleakage under dental composite resins

The aim of this study was to determine the effect of two light-curing units (QTH and LED) on microleakage of Class II composite resin restorations with dentin cavosurface margins. Twenty extracted mandibular first premolars, free of caries and fractures were prepared two vertical slot cavities in the occluso-mesial and -destal surfaces (2 mm buccal-lingually, 2 mm proximal-axially and cervical limit in enamel) and divided into 4 equal groups (n = 8): GI and GII: packable posterior composite light-activated with LED and QTH, respectively; GIII and GIV: micro-hybrid composite resin light-activated with LED and QTH, respectively. The composite resins were applied following the manufacturer's instructions. After 24 h of water storage specimens were subjected to thermocycling for a total of 500 cycles at 5 and 55A degrees C and the teeth were then sealed with impermeable material. Teeth were immersed in 0.5% Basic fuchsin during 24 h at room temperature, and zero to three levels of penetration score were attributed. The Mann-Whitney and Kruskal-Wallis tests showed significant statistically similar (P > 0.05) from GI to GII and GIII to GIV, which the GII (2.750) had the highest mean scores and the GIII and GIV (0.875) had lowest mean scores. The use of different light-curing units has no influence on marginal integrity of Class II composite resin restorations and the proprieties of composite resins are important to reduce the microleakage.

Ultrasonic versus high-speed cavity preparation: Analysis of increases in pulpal temperature and time to complete preparation

Statement of problem. The use of ultrasonic tips has become an alternative for cavity preparation. However, there are concerns about this type of device, particularly with respect to intrapulpal temperatures and cavity preparation time.Purpose. The purpose of this study was to analyze pulpal temperature increases generated by an ultrasonic cavity preparation with chemical vapor deposition (CVD) tips, in comparison to preparation with a high-speed handpiece with a diamond rotary cutting instrument. The time required to complete the cavity preparation with each system was also evaluated.Material and methods. Thermocouples were positioned in the pulp chamber of 20 extracted human third molars. Slot-type cavities (3 x 3 x 2 mm) were prepared on the buccal and the lingual surfaces of each tooth. The test groups were: high-speed cavity preparation with diamond rotary cutting instruments (n = 20) and ultrasonic cavity preparation with CVD points (n = 20). During cavity preparation, the increases In pulpal temperature, and the time required for the preparation, were recorded and analyzed by Student's t test for paired samples (alpha = .05).Results. The average pulpal temperature increases were 4.3 degrees C for the high-speed preparation and 3.8 degrees C for the ultrasonic preparation, which were statistically similar (P = .052). However, significant differences were found (P < .001) for the time expended (3.3 minutes for the high-speed bur and 13.77 minutes for the ultrasound device).Conclusions. The intrapulpal temperatures produced during cavity preparation by ultrasonic tips versus high-speed bur preparation were similar. However, the use of the ultrasonic device required 4 times longer for the completion of a cavity preparation.

Estudo da enxertia hipocotiledonar do maracujazeiro-amarelo sobre dois porta-enxertos, através de microscopia eletrônica de varredura

O objetivo deste trabalho foi verificar quanto tempo após a realização da enxertia hipocotiledonar ocorre a soldadura ou adesão entre enxerto e porta-enxerto, e também a formação da ponte de calo, verificada pelo total preenchimento da fenda por tecido meristemático secundário (calo). Foram produzidas 56 mudas de maracujazeiro-amarelo (Passiflora edulis Sims f. flavicarpa Deg.) pela enxertia hipocotiledonar em fenda cheia no topo sobre dois porta-enxertos (P. edulis Sims f. flavicarpa Deg. e P. alata Dryander). Aos 0, 3, 6, 9, 12, 15 e 18 dias após a enxertia, coletou-se a região da enxertia de quatro mudas de cada combinação. O material coletado foi fixado em solução de glutaraldeído a 3%, pós-fixado em tetróxido de ósmio a 2%, desidratado em uma série de álcool etílico (30, 40, 50, 60, 70, 80, 90, 100%), levado ao secador de ponto crítico (CO2), montado, metalizado com ouro - paládio (35 nm) e, por fim, observados e eletromicrografados em microscópio eletrônico de varredura JEOL JSM 5410 (operado em 15 kV). Verificou-se que, aos seis dias após a enxertia, a soldadura para o porta-enxerto Passiflora alata já havia ocorrido, o que só foi constatado para Passiflora edulis f. flavicarpa aos nove dias. Também, aos nove dias, observou-se para ambos os porta-enxertos a completa formação da ponte de calo, indicando que, a partir daí, pode-se iniciar o processo de aclimatação da muda, para levá-la a um ambiente de menor umidade.

Fator de crescimento derivado de plaquetas humanas obtido por uma metodologia rápida e de baixo custo

Human platelet-derived growth factor (PDGF) was purified from lysates of clinically outdated human platelets by ionic exchange chromatography in CM-Sepharose. The eluated fraction was submitted to the Immunoblot/Slot Blot assay using anti-PDGF-AA and anti-PDGF-BB polyclonal antibodies and was evaluated as to its biological activity through the test of [H 3]-thymidine incorporation in NIH/3T3 cell line fibroblasts in culture. The Immunoblot/Slot Blot assay using anti-PDGF-AA and anti-PDGF-BB antibodies proved the presence of the PDGF in chromatographic cationic fraction. The comparison of biological activities between fiblobrast stimulation assay using recombinant PDGF-AB and partially purified PDGF was demonstrated in 165.796 and 157.567 cpm, respectively. This result, proved the potent mitogenic effect of partially purified PDGF and consequently their evidence about the wound healing activity.

Estudo retrospectivo dos procedimentos anestésicos realizados em cães e gatos submetidos a neurocirurgias

Neurosurgeries are frequent in the routine of veterinary hospitals and, therefore, knowledge of the different anesthetic protocols to be used for each patient is necessary to prevent the morbity and mortality in the after and trans-surgical period. The objectives of this study were to evaluate the anesthetic protocols used in patients undergoing neurosurgeries; the results of those protocols; the rate of complications, and if those complications are related to the duration of the anesthesia time. We studied the anesthetical data of 52 dogs and two cats submitted to neurosurgery between January of 2003 and December of 2006, in the Veterinary Hospital of UEL. Findings showed that the main protocols used were propofol for induction and halothane or isofluorane for maintenance of the anesthesia. These protocols induced adequate anesthesia for the surgical procedure and did not occur complications during the anesthetic period in 37/54 (68,5%) of the cases. 7/19 (36.8%) of the complications observed occurred in patients submitted to anesthesia with halothane and 8/32 (25.2%) in patients with isofluorane. The complication most observed in this study was bradicardy, which occurred in 15/54 (27.8%) of the patients. Two deaths occurred in patients submitted to slot cervical. Good knowledge of the neurological disease and of surgical and anesthetic techniques are essential to prevent alterations in the central nervous system caused by the drugs, disease or association of these factors.

Effect of toothbrushing with different manual toothbrushes on the shear bond strength of orthodontic brackets

The aim of this study was to evaluate the effect of brushing with a Colgate 360° or Oral B Indicator 35 toothbrush on the shear bond strength of orthodontic brackets bonded to extracted human teeth. The bristle wear and bristle tip morphology were also examined after simulated tooth-brushing. Orthodontic brackets (Roth-P/1 st and 2 nd pre-molar S/D- Slot 0.18) were bonded (Transbond XT ®) to the smoothest surface of each of 45 extracted human molar and premolar teeth. Test specimens were randomly divided into three groups: Group 1, control group with no brushing; Group 2, brushing with the Oral B Indicator 35; Group 3, brushing with the Colgate 360°. Samples were adapted to a machine that simulated tooth-brushing. The bond strength of each bracket to each tooth was assessed with a mechanical testing machine. The bristle wear and bristle tip morphology indices were also assessed. Statistically significant differences were defined for p ≤ 0.05. The average bond strengths (range: 90.18-90.89 kgf/cm 2) did not differ among the three groups. The Colgate 360° showed less bristle wear and a better bristle tip morphology than the Oral B Indicator 35 toothbrush. However, use of either toothbrush did not decrease the bond strength of the orthodontic brackets. Therefore, patients undergoing orthodontic therapy can safely use either toothbrush.

Avaliação da fenda e microinfiltração marginal em restaurações de classe II de resina composta, usando as técnicas direta e indireta

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise das angulações mésio-distais de bráquetes pré-ajustados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação do desempenho de um aeromotor de eixo vertical

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação de nove espécies de Eucalyptus spp. em tratamento preservativo industrial

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise in vitro da resistência adesiva de resinas compostas em cavidades de classe II, através do teste de microtração. Efeito de diferentes técnicas restauradoras

Pós-graduação em Ciências Odontológicas - FOAR