Estudio de la pasivacion de la aleacion Co-Cr-Mo en suero fisiologico

Results are presented on the mechanism of passivation of Co-Cr-Mo biological implant alloys in physiological serum using open circuit potentiometry, potentiodynamic curves, and electrochemical impedance spectroscopy. The potential dependence of impedance data and the analysis of the parameters obtained indicate a progressive diminution of the initial layer thickness and the simultaneous formation of a second higher resistive layer. In more severe conditions than the existent in human body, the metallographic examination of the alloy surface shows localized corrosion in interdendritric regions. Elemental analysis of the surface reveals the presence of higher chromium content in these regions. The presence of chlorine was not detected, which suggested that during preferential attack, soluble species are also formed.

Corrosion resistance of Ni-Cr alloys in different mouthwashes

Several alloys have been used for prosthodontics restorations in the last years. These alloys have a number of metals that include gold, palladium, silver, nickel, cobalt, chromium and titanium and they are used in oral cavity undergo several corrosion. Corrosion can lead to poor esthetics, compromise of physical properties, or increased biological irritation. The objective of this study was evaluated corrosion resistance of two alloys Ni-Cr and Ni-Cr-Ti in three types of mouthwashes with different active ingredients: 0.5g/l cetylpyridinium chloride + 0.05% sodium fluoride, 0.05% sodium fluoride + 0.03% triclosan (with fluor) and 0.12% chlorohexidine digluconate. The potentiodynamic curves were performed by means of an EG&G PAR 283 potentiostat/galvanostat. The counter electrode was a platinum wire and reference electrode was an Ag/AgCl, KCl saturated. Before each experiment, working electrodes were mechanically polished with 600 and 1200 grade papers, rinsed with distilled water and dried in air. All experiments were carried out at 37.0oC in conventional three-compartment double wall glass cell containing mouthwashes. The microstructures of two alloys were observed in optical microscopy. Analysis of curves showed that Ni-Cr alloy was less reactive in the presence of 0.12% chlorohexidine digluconate while Ni-Cr-Ti alloy was more sensitive for others two types of mouthwashes (0.5g/l cetylpyridinium chloride + 0.05% sodium fluoride  and 0.05% sodium fluoride + 0.03% triclosan). This occurred probably due presence of titanium in this alloy. Microstructural analysis reveals the presence of dendritic and eutectic microstructures for NiCr and Ni-Cr-Ti, respectively.

Mathematical analysis of maximum power generated by photovoltaic systems and fitting curves for standard test conditions

The rural electrification is characterized by geographical dispersion of the population, low consumption, high investment by consumers and high cost. Moreover, solar radiation constitutes an inexhaustible source of energy and in its conversion into electricity photovoltaic panels are used. In this study, equations were adjusted to field conditions presented by the manufacturer for current and power of small photovoltaic systems. The mathematical analysis was performed on the photovoltaic rural system I- 100 from ISOFOTON, with power 300 Wp, located at the Experimental Farm Lageado of FCA/UNESP. For the development of such equations, the circuitry of photovoltaic cells has been studied to apply iterative numerical methods for the determination of electrical parameters and possible errors in the appropriate equations in the literature to reality. Therefore, a simulation of a photovoltaic panel was proposed through mathematical equations that were adjusted according to the data of local radiation. The results have presented equations that provide real answers to the user and may assist in the design of these systems, once calculated that the maximum power limit ensures a supply of energy generated. This real sizing helps establishing the possible applications of solar energy to the rural producer and informing the real possibilities of generating electricity from the sun.

Maturation and growth curves of Macrobrachium Carcinus (Linnaeus) (Crustacea, Decapoda, Palaemonidae) from Ribeira de Iguape River, southern Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Models for the analysis of growth curves for rearing tinamous (Rhynchotus rufescens) in captivity

Growth curves models provide a visual assessment of growth as a function of time, and prediction body weight at a specific age. This study aimed at estimating tinamous growth curve using different models, and at verifying their goodness of fit. A total number 11,639 weight records from 411 birds, being 6,671 from females and 3,095 from males, was analyzed. The highest estimates of a parameter were obtained using Brody (BD), von Bertalanffy (VB), Gompertz (GP,) and Logistic function (LG). Adult females were 5.7% heavier than males. The highest estimates of b parameter were obtained in the LG, GP, BID, and VB models. The estimated k parameter values in decreasing order were obtained in LG, GP, VB, and BID models. The correlation between the parameters a and k showed heavier birds are less precocious than the lighter. The estimates of intercept, linear regression coefficient, quadratic regression coefficient, and differences between quadratic coefficient of functions and estimated ties of quadratic-quadratic-quadratic segmented polynomials (QQQSP) were: 31.1732 +/- 2.41339; 3.07898 +/- 0.13287; 0.02689 +/- 0.00152; -0.05566 +/- 0.00193; 0.02349 +/- 0.00107, and 57 and 145 days, respectively. The estimated predicted mean error values (PME) of VB, GP, BID, LG, and QQQSP models were, respectively, 0.8353; 0.01715; -0.6939; -2.2453; and -0.7544%. The coefficient of determination (RI) and least square error values (MS) showed similar results. In conclusion, the VB and the QQQSP models adequately described tinamous growth. The best model to describe tinamous growth was the Gompertz model, because it presented the highest R-2 values, easiness of convergence, lower PME, and the easiness of parameter biological interpretation.

Corrosion behavior of Ti-6Al-4V alloy treated by plasma immersion ion implantation process

Ti-6Al-4V alloy is one of the most frequently used Ti alloys with diverse applications in aerospace and biomedical areas due to its favorable mechanical properties, corrosion resistance and biocompatibility. Meanwhile, its surface can stiffer intense corrosion caused by wear processes due to its poor tribological properties. Thus in the present study, PIII processing of Ti-6Al-4V alloy was carried out to evaluate its corrosion resistance in 3.5% NaCl solution. Two different sets of Ti-6Al-4V samples were PIII treated, varying the plasma gases and the treatment time. The corrosion behavior is correlated with the surface morphology, and the nitrogen content. SEM micrographs of the untreated sample reveal a typical two-phase structure. PIII processing promotes surface sputtering and the surface morphology is completely different for samples treated with N-2/H-2 mixture and N-2 only. The highest penetration of nitrogen (similar to 88 nm), corresponding to 33% of N-2 was obtained for the sample treated with N-2/H-2 mixture for 1:30 h. The corrosion behavior of the samples was investigated by a potentiodynamic polarization method. A large passive region of the polarization curves (similar to 1.5 V), associated with the formation of a protective film, was observed for all samples. The passive current density (similar to 3 x 10(-6) A cm(-2)) of the PIII-treated Ti-6Al-4V samples is about 10 times higher than for the untreated sample. This current value is still rather low and maintains good corrosion resistance. The anodic branches of the polarization curves for all treated Ti-6Al-4V samples demonstrate also that the oxide films break down at approximately 1.6 V, forming an active region. Although the sample treated by N-2/H-2 mixture for 1.30 It has thicker nitrogen enriched layer, better corrosion resistance is obtained for the PIII process performed with N, gas only. (c) 2007 Elsevier B.V. All rights reserved.

Enhanced corrosion resistance of AISI H13 steel treated by nitrogen plasma immersion ion implantation

Electrochemical corrosion measurements of AISI H13 steel treated by Pill process in 3.5% (wt) NaCl solution were investigated. So far the corrosion behavior of AISI H 13 steel by Pill has not been studied. The electrochemical results are correlated with the surface morphology, nitrogen content and hardness of the nitride layer. Ion implantation of nitrogen into H 13 steel was carried out by Pill technique. SEM examination revealed a generalized corrosion and porosity over all analyzed sample surfaces. Penetration of nitrogen reaching more than 20 gm was achieved at 450 degrees C and hardness as high as 1340 HV (factor of 2.7 enhancement over standard tempered and annealed H 13) was reached by a high power, 9 h Pill treatment. The corrosion behavior of the samples was studied by potentiodynamic polarization method. The noblest corrosion behavior was observed for the samples treated by PIII at 450 degrees C, during 9 h. Anodic branches of polarization curves of PIII processed samples show a passive region associated with the formation of a protective film. The passive region current density of PIII treated H13 samples (3.5 x 10(-6) A/cm(2)) is about 270 times lower than the one of untreated specimens, which demonstrates the higher corrosion resistance for the Pill treated H 13 samples. (c) 2007 Elsevier B.V. All rights reserved.

A Parameterization Technique for the Continuation Power Flow Developed from the Analysis of Power Flow Curves

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Differential geometry of intersection curves in R(4) of three implicit surfaces

We present algorithms for computing the differential geometry properties of intersection Curves of three implicit surfaces in R(4), using the implicit function theorem and generalizing the method of X. Ye and T. Maekawa for 4-dimension. We derive t, n, b(1), b(2) vectors and curvatures (k(1), k(2), k(3)) for transversal intersections of the intersection problem. (C) 2008 Elsevier B.V. All rights reserved.

On certain curves of genus three in characteristic two

We study curves of genus 3 over algebraically closed fields of characteristic 2 with the canonical theta characteristic totally supported in one point. We compute the moduli dimension of such curves and focus on some of them which have two Weierstrass points with Weierstrass directions towards the support of the theta characteristic. We answer questions related to order sequence and Weierstrass weight of Weierstrass points and the existence of other Weierstrass points with similar properties.

Evaluation of water beef buffalo from birth to two years using different growth curves

The buffalo is a domestic animal species of growing world-wide importance. Research to improve genetic improvement programs is important to maintain the productivity of buffalo. The objective this research was to evaluate the growth of Brazilian buffalo to two years of age with different growth curves. Growth curves consolidate the information contained in the weight-age data into three or four biologically meaningful parameters. The data included 31,452 weights at birth and 120, 205, 365, 550 and 730 days of buffalo (n = 5,178) raised on pasture without supplementation. Logistic, Gompertz, quadratic logarithmic, and linear hyperbolic curves (designated L, G, QL, and LH, respectively) were fitted to the data by using proc NUN of SAS (SAS Institute, Inc., Cary, NC, USA). The parameters estimates for L [WT= A * (((1 + exp (-k * AGE)))**-m)] were A = 865.1 +/- 5.42; k= 0.0028 +/- 0.00002; M= 3.808 +/- 0.007; R(2) = 0.95. For G [WT= A * exp (-b * exp (-k * age)] the parameters estimates were A= 967.6 +/- 7.23; k = 0.00217 +/- 0.000015; b = -2.8152 +/- 0.00532. For QL [WT= A + b*age + k*(age*age) + m*log (age)] parameters estimates were A= 37.41 +/- 0.48; k= 0.00019 +/- 6.4E(-6); b= 0.539 +/- 0.006; m= 2.32 +/- 0.23; R(2)=0.96. For LH [WT= A + b*AGE + k*(1/AGE)] the parameters estimates were A= 23.15 +/- 0.44; k=15.16 +/- 0.66; b= 0.707 +/- 0.001; R(2)= 0.96. Each of these curves fit these data equally well and could be used for characterizing growth to two years in beef buffalo.

Critical points in logistic growth curves and treatment comparisons

Several biological phenomena have a behavior over time mathematically characterized by a strong increasing function in the early stages of development, then by a less pronounced growth, sometimes showing stability. The separation between these phases is very important to the researcher, since the maintenance of a less productive phase results in uneconomical activity. In this report we present methods of determining critical points in logistic functions that separate the early stages of growth from the asymptotic phase, with the aim of establishing a stopping critical point in the growth and on this basis determine differences in treatments. The logistic growth model is fitted to experimental data of imbibition of arariba seeds (Centrolobium tomentosum). To determine stopping critical points the following methods were used: i) accelerating growth function, ii) tangent at the inflection point, iii) segmented regression; iv) modified segmented regression; v) non-significant difference; and vi) non-significant difference by simulation. The analysis of variance of the abscissas and ordinates of the breakpoints was performed with the objective of comparing treatments and methods used to determine the critical points. The methods of segmented regression and of the tangent at the inflection point lead to early stopping points, in comparison with other methods, with proportions ordinate/asymptote lower than 0.90. The non-significant difference method by simulation had higher values of abscissas for stopping point, with an average proportion ordinate/asymptote equal to 0.986. An intermediate proportion of 0.908 was observed for the acceleration function method.

Senna occidentalis Link. (Caesalpiniaceae) imbibition curves for NaCl osmotic potential levels up to 0.6 MPa

An investigation is reported on the statistical model of imbibition curves of the seeds of Senna occidentalis Link. (Caesalpiniaceae), up to Phase II (start of root emission) in osmotic potential levels (0; -0.2; -0.4 and -0.6 MPa), induced NaCl or PEG 6000. The statistical model for both solutions was y = a [1 b exp(-cx)] where y is the fresh matter of seed in g, and x the time of evaluation in h. The analysis of variance of the estimated parameters, showed that with the NaCl solution, the -0.4 and -0.6 MPa levels differed significantly from the 0 and -0.2 MPa levels, and that with the PEG solution, the -0.6 MPa differed from the rest. Prolongation of Phase II occurred as the potential decreased, with both solutions. More reduction in water uptake and prolongation of this phase occurred with the PEG treatment.

Curves in homogeneous spaces and their contact with 1-dimensional orbits

Let alpha be a C(infinity) curve in a homogeneous space G/H. For each point x on the curve, we consider the subspace S(k)(alpha) of the Lie algebra G of G consisting of the vectors generating a one parameter subgroup whose orbit through x has contact of order k with alpha. In this paper, we give various important properties of the sequence of subspaces G superset of S(1)(alpha) superset of S(2)(alpha) superset of S(3)(alpha) superset of ... In particular, we give a stabilization property for certain well-behaved curves. We also describe its relationship to the isotropy subgroup with respect to the contact element of order k associated with alpha.

Resistência à corrosão das fases presentes em amálgamas dentários

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)