Effect of thermocycling on the flexural and impact strength of urethane-based and high-impact denture base resins

Objective: Mechanical properties of the acrylic resins used for denture fabrication may be influenced by water and temperature. Thus, the aim of this study was to evaluate the effect of thermocycling on the flexural and impact strength of a high-impact (Lucitone 199) and a urethane-based denture material (Eclipse).Materials and methods: Flexural strength (64 x 10 x 3.3 mm) and impact strength (60 x 6 x 4 mm) specimens were made following the manufacturers' instructions and assigned to two groups (n = 10): control (C) - not thermocycled - and T - thermocycled (5000 cycles between 5 and 55 degrees C). Specimens were submitted to three-point bending and Charpy impact tests.Results: Flexural strength (MPa) and impact strength (kJ/m(2)) data were analysed with two-way ANOVA (p = 0.05). The flexural strength of material Eclipse (C, 136.5; T, 130.7) was significantly higher than that of resin Lucitone 550 (C, 99.4; T, 90.1). Material Eclipse exhibited significantly higher impact strength (C, 6.9; T, 5.3) than the resin Lucitone 550 (C, 3.5; T, 3.0). For both materials, a significant decrease in flexural and impact strengths was observed when the specimens were thermocycled.Conclusion: Flexural and impact strengths were higher for Eclipse than for Lucitone 550, in both groups. Thermocycling decreased the flexural and impact strengths of Eclipse and Lucitone 550.

Impact strength of denture base and reline acrylic resins subjected to long-term water immersion

Water may influence the mechanical properties of the acrylic resins. Thus, the effect of water storage on the impact strength (IS) of one denture base (Lucitone 550 - L) and four reline resins (Tokuyama Rebase II - T; UfiGel Hard - U; Kooliner - K; New Truliner - NT) was evaluated. Bars of L were made (60 x 6 x 2 mm) and relined (2 mm) with T, U, K, NT and L. Intact specimens of each material (60 x 6 x 4 mm) were also fabricated for comparative purposes. Specimens were submitted to Charpy impact tests without water storage (control) and after immersion in water for 7, 90 and 180 days. Data (kJ/m 2) analyzed by two-way ANOVA and Tukey's test (p=0.05) revealed that after 90 days, U exhibited an increase in the IS (0.93) compared to 7 days (0.58). K (1.48) and L/K (7.21) exhibited a decrease at the 7-day period (1.01 and 3.23, respectively). NT (0.60) showed an increase in the IS after 180 days (1.52), whereas L/ NT (7.70) showed a decrease (3.17). Water immersion improved the IS of U and NT, and decreased the IS of K, L/K, and L/NT. Water may affect differently the IS of acrylic resins and, consequently, the resistance to fracture of relined denture bases.

Resistance to impact of cross-linked denture base biopolymer materials: Effect of relining, glass flakes reinforcement and cyclic loading

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Modeling field load tests in lateritic unsaturated soil

Many models for unsaturated soil have been developed in the last years, accompanying the development of experimental techniques to deal with such soils. The benchmark of the models for unsaturated soil can be assigned to the Barcelona Basic Model (BBM) now incorporated in some codes such as the CODE_BRIGHT. Most of those models were validated considering limited laboratory test results and not much validation is available considering real field problems. This paper presents modeling results of field plate load tests performed under known suction on a lateritic unsaturated soil. The required input data were taken from laboratory tests performed under suction control. The modeling nicely reproduces field tests allowing appreciating the influence of soil suction on the stress-settlement curve. In addition, wetting induced or collapse settlements were calculated from field tests and were nicely duplicated by the numerical analysis performed.

Construction and demolition waste as a source of PVC for recycling

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Durability of adhesives based on different epoxy/aliphatic amine networks

The mechanical and adhesives properties of epoxy formulations based on diglycidyl ether of bisphenol A cured with various aliphatic amines were evaluated in the glass state. Impact tests were used to determine the impact energy. The adhesive properties have been evaluated in terms single lap shear using steel adherends. Its durability in water at ambient temperature (24 degrees C) and at 80 degrees C has also been analyzed. The fracture mechanisms were determined by optical microscopy. It was observed a strong participation of the cohesive fracture mechanisms in all epoxy system studied. The 1-(2-aminoethyl)piperazine epoxy adhesive and piperidine epoxy adhesive presents the best adhesive strength and the largest impact energy. The durability in water causes less damage to piperidine epoxy networks. This behavior appears to be associated with the lower water uptake tendency of homopolymerised resins due to its lower hydroxyl group concentration. (C) 2011 Elsevier Ltd. All rights reserved.

Perfil sorológico anti-Brucella abortus em bezerras vacinadas com amostras B19

The serological profiles of 33 female bovines, vaccinated at three to eight months of age with the B19 standard strain of Brucella abortus, were studied over a period of 728 days, using the following agglutination procedures: plate agglutination, tube agglutination, rose bengal plate and mercaptoethanol test. Maximum levels of antibodies detected reached by the plate agglutination and tube agglutination tests were found between the 14(th) and 42(nd) day, and with mercaptoethanol test, between the 28(th) and 42(nd) day. Anti-Brucella antibodies decreased thereafter. At 182 days after vaccination, five suspected animals and one positive were detected by the plate agglutination test, while by the tube agglutination test, only one animal was suspected and another one was positive. During the same period, positive reactions were found in six animals by means of the mercaptoethanol test, and five positives by the rose bengal test. By means of tube agglutination and plate agglutination tests, the animals became serologically negative at 245 and 273 days, respectively, after the vaccination, based on the rules adopted for the vaccinated animals. Using the mercaptoethanol and rose bengal plate tests, all the animals were found to be negative at 308 days after vaccination.

Thermal properties of nylon6/ABS polymer blends: Compatibilizer effect

Nylon6/ABS binary blends are incompatible and need to be compatibilized to achieve better performance under impact tests. Poly(methyl methacrylate/maleic anhydride) (MMA-MA) is used in this work to compatibilize in situ nylon6/ABS immiscible blends. The MA functional groups, from MMA-MA copolymers, react with NH2 groups giving as products nylon molecules grafted to MMA-MA molecules. Those molecular species locate in the nylon6/ABS blend interfacial region increasing the local adhesion. MMA-MA segments are completely miscible with the SAN rich phase from the ABS. The aim of this work is to study the effects of ABS and compatibilizing agent on the melting and crystallization of nylon6/ABS blends. This effect has been investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). Incorporation of this compatibilizer and ABS showed little effect on the melting behavior of the PA6 crystalline phase, in general. DMTA analysis confirmed the system immiscibility and showed evidence of compatibility between the two phases, nylon6 and ABS, produced by MMA-MA copolymer presence. The nylon6/ABS blend morphology, observed by transmission electron microscopy (TEM), changes significantly by the addition of the MMA-MA compatibilizer. A better dispersion of ABS in the nylon6 phase is observed. © 2004 Kluwer Academic Publishers.

Efeito de tratamentos da superfície de união e materiais reembasadores na resistência ao impacto de resina para base de prótese

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do potencial do impacto ambiental de águas residuárias de abatedouros avícolas e suinícolas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Epidemiologia da brucelose bovina nos municípios de Altinópolis e Santo Antônio da Alegria, Estado de São Paulo: prevalência, fatores de risco e métodos de diagnóstico

Pós-graduação em Medicina Veterinária - FCAV

Impact of Road Clearings on the Movements of Three Understory Insectivorous Bird Species in the Brazilian Atlantic Forest

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Numerical simulation of drop impact and jet buckling problems using the eXtended Pom-Pom model

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Impact of maternal mild hyperglycemia on maternal care and offspring development and behavior of Wistar rats

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Metabolic syndrome and dementia associated with Parkinson's disease: impact of age and hypertension

Objective: To determine correlations between age and metabolic disorders in Parkinson's disease (PD) patients. Methods: This observational cross-sectional study included brief tests for dementia and the Mattis test. Signals of metabolic syndrome were evaluated. Results: There was no significant effect from the presence of hypertension (OR=2.36 for patients under 65 years old and OR=0.64 for patients over 65), diabetes or hypercholesterolemia regarding occurrences of dementia associated with PD (24% of the patients). The study demonstrated that each year of age increased the estimated risk of dementia in PD patients by 9% (OR=1.09; 95%Cl: 1.01-1.17). Conclusion: There was no evidence to correlate the presence of metabolic syndrome with the risk of dementia that was associated with PD. The study confirmed that dementia in PD is age dependent and not related to disease duration.