Desempenho de trator agrícola em três superfícies de solo e quatro velocidades de deslocamento

The aim of this work was to evaluate tractor performance in soil with three different surfaces: firm soil without covering, mobilized soil, and firm soil with vegetal residue of corn and braquiaria, for four forward speeds. The experiment was accomplished in three plots determined by the soil conditions. In each plot four treatments were composed by the forward speed obtained by the changes of the tractor gear. Six repetitions were used in each plot, totaling 72 experimental units, combination of the traction, slip of the rear and front wheels, forward speed and fuel consumption. The values of the tractor performance obtained led to the conclusion that in the firm soil without vegetable covering the tractor performance was better, followed by the soil with the firm surface and covered with corn straw and braquiaria and finally the mobilized soil. The best tractor performance was obtained in the C1 gear that supplied the forward speed of 6 km h(-1).

Evaluation of tractive performance of four agricultural tractors in laterally inclined terrain

O presente trabalho teve como objetivo avaliar o desempenho operacional de quatro tratores agrícolas com tração dianteira auxiliar, em função de seis inclinações laterais, em uma pista lateral de ensaios, pertencente à Faculdade de Ciências Agronômicas da Universidade Estadual Paulista, Câmpus de Botucatu. As inclinações laterais foram 0; 5; 10; 15; 20 e 25 graus. em todas estas situações, os tratores operaram com carga predeterminada de tração imposta ao trator tracionado de 40 kN na inclinação de 0 grau. Portanto, foi utilizado um delineamento em blocos casualizados (DBC), sendo seis inclinações e quatro tratores, e com três repetições para cada tratamento. As variáveis analisadas foram patinhagem, força de tração, consumo horário de combustível e velocidade de deslocamento. Concluiu-se que a configuração dos rodados pneumáticos influenciaram no desempenho operacional dos tratores, conforme aumentaram as inclinações laterais do terreno.

Desenvolvimento e produtividade da cana-de-açúcar após aplicação de reguladores vegetais em meio de safra

The supply of technological quality raw material for providing economical return is the most important necessity of sugar and alcohol industry. The objective of this work was to evaluate the development and productivity of sugarcane stalks due to plant regulators application at half crop. The experiment was carried out in a randomized block design with five replications. The treatments consisted of four plant regulators of the class of the growth retainers (Ethephon, Ehyl-trinexapac, Potassium nitrate, Potassium nitrate + Boron) application and a control (natural ripening). Ethyl-trinexapac and Ethephon treatments were efficient to hold up growth process regarding height of plants, but had no effect on diameter of stalks. The maintenance of bud top integrity made possible the increase in diameter of stalks, without interrupting the growth process regarding height of plants. According to application time the ripeners provided improvement on technological quality of raw material. The ripeners did not affect the number of plants per meter at harvest and did not cause quantitative alterations in the mass of stalks per hectare. The ripeners did not affect the regrowth of the ratoon cane.

Adubação nitrogenada em cobertura no feijoeiro com suplementação de molibdênio via foliar

The objective of this work was to evaluate the effect of leaf spray of molybdenum (Mo) and nitrogen (N) rates in common bean (Phaseolus vulgaris L.), cultivar Carioca Precoce, evaluating the yield components, yield and leaves nitrate levels. The research was carried out in Botucatu, State of São Paulo, Brazil. The sowing of the beans (06/03/2003) was made with the supply of 230 kg ha(-1) of NPK (4-30-10) granulated fertilizer at planting. The experiment was a complete randomized block, with four replications and a 5 x 2 factorial arrangement, involving five N rates (25; 50; 75 and 125 kg ha(-1)), applied 20 days after emergency (DAE), with or without 80 g ha(-1) of Mo, applied on leaves at 25 DAE. The Mo absence by leaf spray promoted the nitrate accumulation in the leaves in treatments with higher rates of N. The weight of 100 grains increased with the Mo by leaf spray, reducing the need for N to get the best results. The molybdenum fertilization increased bean yield regardless of N rate applied to the beans.

Does the Ultrasonic Cleaning Medium Affect the Adhesion of Resin Cement to Feldspathic Ceramic?

Purpose: To evaluate the effect of different cleaning media on the adhesion of resin cement to feldspathic ceramic after etching.Materials and Methods: The cementation surfaces of ceramic blocks (N = 20, n = 5 per group) were etched with 10% hydrofluoric acid (HF) gel for 20 s and rinsed for 60 s. They were then randomly assigned to 4 groups: G1: air-water spray+drying (control); G2: ultrasonic cleaning in distilled water for 4 min+drying; G3: ultrasonic cleaning in 99.5% acetone for 4 min+drying; G4: ultrasonic cleaning in 70% alcohol for 4 min+drying. The ceramic blocks were silanized and cemented (RelyX ARC) to the composite blocks. Subsequently, the microtensile bond strength test (mu TBS) was performed. In addition, EDS analysis was made to assess the elemental composition of the conditioned and cleaned ceramic surfaces.Results: A significantly higher mean mu TBS was obtained when specimens had been ultrasonically cleaned in distilled water (G2: 18.8 +/- 0.4 MPa) (p < 0.05) compared to other groups (G1: 16.6 +/- 0.5; G3: 16.1 +/- 0.9; G4: 15.8 +/- 1.4) (one-way ANOVA). EDS analysis indicated the presence of F- only in G1. Dissolved precipitates after HF etching were removed by ultrasonic cleaning.Conclusion: Cleaning the HF-etched ceramic surface ultrasonically in distilled water is recommended, instead of rinsing it with air-water spray only.

Estoques e frações de carbono orgânico em Latossolo Amarelo submetido a diferentes sistemas de manejo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The venomous toadfish Thalassophryne nattereri (niquim or miquim): report of 43 injuries provoked in fishermen of Salinópolis (Pará State) and Aracaju (Sergipe State), Brazil

Os peixes da família Batrachoididae causam um grande número de acidentes em pescadores das regiões Norte e Nordeste do Brasil. O gênero Thalassophryne apresenta várias espécies no Brasil e a espécie Thalassophryne nattereri é a mais comum, todas apresentando veneno. O veneno é inoculado por duas espículas ocas na nadadeira dorsal e duas nas regiões pré-operculares, ligadas a uma glândula de veneno na base. Os envenenamentos causaram dor intensa, edema e eritema iniciais em 43 pescadores observados em Salinópolis (Pará) e Aracaju (Sergipe). em todos os casos, não ocorreram fenômenos sistêmicos dignos de nota, mas ocorreu necrose local em oito pacientes e infecção bacteriana em dez. As circunstâncias dos acidentes são comentadas, assim como aspectos terapêuticos. Nossa conclusão foi que o envenenamento por Thalassophryne é importante e freqüente e deve ser considerado de média gravidade, em função de não haverem fenômenos sistêmicos, como observado nos acidentes por peixes-escorpião (Scorpaena) ou arraias marinhas e fluviais.

Repair bond strength of a resin composite to alumina-reinforced feldspathic ceramic

This study compared the microtensile bond strength of a repair resin to an alumina-reinforced feldspathic ceramic (Vitadur-alpha, Vita) after 3 surface conditioning methods: Group 1, etching with 9.6% hydrofluoric acid for 1 minute plus rinsing and drying, followed by application of silane for 5 minutes; group 2, airborne particle abrasion with 110-mm aluminum oxide using a chairside air-abrasion device followed by silane application for 5 minutes; group 3, chairside tribochemical silica coating with 30-mu m SiOx followed by silane application for 5 minutes (N = 30). Group 1 presented the highest mean bond strength (19.7 +/- 3.8 MPa), which was significantly higher than those of groups 2 (10 +/- 2.6 MPa) and 3 (10.4 +/- 4 MPa) (P <.01). Scanning electron microscope analysis of the failure modes demonstrated predominantly mixed types of failures, with adhesive and/or cohesive failures in all experimental groups.

Ausência de patogenicidade de Xylella fastidiosa da escaldadura da folha da ameixeira na cultivar de pessegueiro flordasun

Xylella fastidiosa associated to plum leaf scald is reported to belong to the same group of the strain that causes the phony disease of peach. Plants of plum cultivars Santa Rosa and Harry Pickstone and peach cultivar Flordasun, grafted on peach rootstock, were inoculated by using buds collected from plum plants severely infected with X. fastidiosa. Peach plants did not develop symptoms of phony disease, after four years in the greenhouse. In contrast, plum plants from both cultivars inoculated either in the rootstock or in the canopy developed leaf scald symptoms. DAS-ELISA tests with antibody against X. fastidiosa and isolation on BCYE medium indicated the presence of the bacterium in plum tissues. These tests were negative for Flordasun peach for both stem and root samples.

Infância, experiência e tempo

Definida pelo autor César Donizetti Pereira Leite como uma pesquisa acadêmica com formato de ensaio esta obra reúne um conjunto de textos instigantes, abertos e experimentais sobre infância e educação, mas que tem neste tema apenas o ponto de partida. A intenção do autor é, mais do que comprovar alguma tese eventualmente sugerida no título da obra, mergulhar no universo infantil e retirar dele as ricas relações cultivadas pela criança com a sua realidade, com todas as suas variáveis e nuances, incluídas suas experiências com o cinema, a literatura, a passagem do tempo, os espaços, a escola. Leite não pensou a infância como algo a ser escrito ou dito, e sim vivenciado. Saborosamente fragmentado, o livro utiliza de maneira aparentemente aleatória as mais diferentes modalidades de escritura - de pequenos ensaios críticos a insights iluminadores, de poemas e citações infantis a trechos de terceiros. E faz a infância emergir com todos os seus contornos, como se ela mesma produzisse uma forma de escrever sobre ela, fabricasse uma escritura que a contornasse. É texto, mas também metatexto, e dos mais bem-sucedidos já escritos sobre o assunto.

Can Heat Treatment Procedures of Pre-hydrolyzed Silane Replace Hydrofluoric Acid in the Adhesion of Resin Cement to Feldspathic Ceramic?

Purpose: To evaluate the influence of heat treatment (HT) procedures of a pre-hydrolyzed silane on bond strength of resin cement to a feldspathic ceramic.Materials and Methods: Ceramic and composite blocks (N = 30) were divided into six groups (n = 5) and subjected to the following conditioning procedures: G1: 9.6% hydrofluoric acid (HF) for 20 s + silane (RelyX Ceramic Primer, 3M ESPE) + resin cement (Panavia F2.0, Kuraray) (control); G2: HF (20 s) + silane + heat treatment in furnace (HTF) (100 degrees C, 2 min) + resin cement; G3: silane + HTF + resin cement; G4-HF (20 s) + silane + heat treatment with hot air (HTA) (50 +/- 5 degrees C for 1 min) + resin cement; G5: silane + HTA + resin cement; G6: silane + resin cement. The microtensile bond strength (MTBS) test was performed using a universal testing machine (1 mm/min). After debonding, the substrate and adherent surfaces were analyzed using a stereomicroscope and SEM to categorize the failure types. The data were statistically evaluated using one-way ANOVA and Tukey's test (5%).Results: The control group (G1) showed no pre-test failures and presented significantly higher mean MTBS (16.01 +/- 1.12 MPa) than did other groups (2.63 +/- 1.05 to 12.55 +/- 1.52 MPa) (p = 0.0001). In the groups where HF was not used, HTF (G3: 12.55 +/- 1.52 MPa) showed significantly higher MTBS than did HTA (G5: 2.63 +/- 1.05 MPa) (p < 0.05). All failure types were mixed, ie, adhesive between the resin cement and ceramic accompanied by cohesive failure in the cement.Conclusion: Heat treatment procedures for the pre-hydrolyzed silane either in a furnace or with the application of hot air cannot replace the use of HF gel for the adhesion of resin cement to feldspathic ceramic. Yet when mean bond strengths and incidence of pre-test failures are considered, furnace heat treatment delivered the second best results after the control group, being considerably better than hot air application.

Analysis of the procedures used to evaluate suicide crime scenes in Brazil: A statistical approach to interpret reports

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Previsão de demanda de veículos automotores através do modelo de regressão linear múltipla

This study aimed to model a equation for the demand of automobiles and light commercial vehicles, based on the data from February 2007 to July 2014, through a multiple regression analysis. The literature review consists of an information collection of the history of automotive industry, and it has contributed to the understanding of the current crisis that affects this market, which consequence was a large reduction in sales. The model developed was evaluated by a residual analysis and also was used an adhesion test - F test - with a significance level of 5%. In addition, a coefficient of determination (R2) of 0.8159 was determined, indicating that 81.59% of the demand for automobiles and light commercial vehicles can be explained by the regression variables: interest rate, unemployment rate, broad consumer price index (CPI), gross domestic product (GDP) and tax on industrialized products (IPI). Finally, other ten samples, from August 2014 to May 2015, were tested in the model in order to validate its forecasting quality. Finally, a Monte Carlo Simulation was run in order to obtain a distribution of probabilities of future demands. It was observed that the actual demand in the period after the sample was in the range that was most likely to occur, and that the GDP and the CPI are the variable that have the greatest influence on the developed model

Risco à saúde representado pelo consumo de leite cru comercializado clandestinamente

Foram submetidas às contagens de microrganismos mesófilos, Staphylococccus coagulase positiva, e às determinações do número mais provável (NMP) de coliformes totais e de coliformes fecais, 60 amostras de leite cru comercializado clandestinamente nos Municípios de Botucatu e de São Manuel, Estado de São Paulo, Brasil. Os resultados obtidos evidenciaram a ocorrência de 41 (68,3%) e 50 (83,3%) amostras com contagens de microrganismos mesófilos e de coliformes totais, respectivamente, acima dos limites máximos estabelecidos pelo Ministério da Saúde para o leite pasteurizado tipo C. Evidenciaram, ainda, a presença de 30 (50,0%) e 11 (18,3%) amostras contaminadas por cepas de Staphylococcus coagulase positiva e por coliformes fecais, respectivamente. Apenas 5 (8,3%) amostras mostraram-se dentro dos referidos padrões legais.