Influence of pre-heat treatment and different light-curing units on Vickers hardness of a microhybrid composite resin

The aim of this study was to evaluate the hardness of a dental composite resin submitted to temperature changes before photo-activation with two light-curing unite (LCUs). Five samples (4 mm in diameter and 2 mm in thickness) for each group were made with pre-cure temperatures of 37, 54, and 60°C. The samples were photo-activated with a conventional quartz-tungsten-halogen (QTH) and blue LED LCUs during 40 s. The hardness Vickers test (VHN) was performed on the top and bottom surfaces of the samples. According to the interaction between light-curing unit and different pre-heating temperatures of composite resin, only the light-curing unit provided influences on the mean values of initial Vickers hardness. The light-curing unit based on blue LED showed hardness mean values more homogeneous between the top and bottom surfaces. The hardness mean values were not statistically significant difference for the pre-cure temperature used. According to these results, the pre-heating of the composite resin provide no influence on Vickers hardness mean values, however the blue LED showed a cure more homogeneous than QTH LCU. © 2009 Pleiades Publishing, Ltd.

Variação genética, interação genótipo solo e ganhos na seleção em teste de progěnies de Corymbia citriodora Hook em Luiz Antonio, São Paulo

The aim of this study was to investigate the genetic variation, the genotype × soil interaction and the selection among and within Corymbia citriodora progenies in three different kinds of soils (Red Latossol, Quartz Sand and Purple Latossol), which occur in the Luiz Antônio Experimental Station, São Paulo State, Brazil. The progeny test was established 1983, using 56 open-pollinated families of C. citriodora. Twenty fve years after planting the following traits were measured: height, diameter at breast height (Dbh), stem form and survival. Best growth occurred in Purple Latossol. Significant differences among progenies were detected for most traits in all sites, suggesting the possibility of improvement by selection. In the analysis with sites, Significant differences among locals, progenies and genotypes × soil interaction were detected, confiming that the tested material has sufficient genetic variation to be explored by selection in all sites. The analysis of genotype × soil interaction indicates that growth traits present single interaction and the same progenies can be selected in each site. On the order hand, genotype × soil interaction for stem form and survival was complex; and specifc progenies need to be selected for each kind of soil. The population, due to its high genetic variation and strong genetic control of traits, permits to obtain considerable genetic gains by selection among and within progenies.

Respostas de clones de Eucalyptus grandis e E. grandis x E. urophylla à supressão de boro

The present work had as objective the study of clones of Eucalyptus grandis and E. grandis × E. urophylla under boron suppression on growth in height and diameter, development of symptoms of deficiency, boron content in leaf and polyols production. Plants were cultivated in pots with quartz in a greenhouse using two levels of boron per solution (0 and 0.5 mg L-1 of B). The 32 treatments followed a factorial scheme: 16 × 2 -16 clones and two doses of boron in a randomized block experimental design, with fve repetitions, totaling 160 plots. Plants were evaluated weekly for deficiency symptoms and monthly for height, stem diameter and leaf content of boron in different plant parts. The content of polyols was measured in two occasions: at 162 days and 192 days after starting the experiment. Decrease of growth and quick development of deficiency symptoms 40 days after boron suppression were observed, as well as a decrease of polyols synthesis. Foliar analysis, with boron supplement, resulted in the presence of mannitol and sorbitol in high enough concentration so that the evaluated plants could be considered rich in those polyols. Under boron suppression, boron levels in different portions of branches and stems of plants, as well as the presence of mannitol and sorbitol, indicated a conditional mobility of boron in Eucalyptus.

Sintering temperature influence on microwave dielectric properties of TiO2-ZrO2 ceramics

Dielectric ceramics have been widely investigated and used for microwave applications such as resonators and filters. The present study deals with the influence of sintering temperature on microwave dielectric properties of TiO2 ceramics with 10, 20, and 30 wt% ZrO2. Three compositions have been developed through mixing procedures and then tested for each sintering temperature: 1500 and 1400°C. X-ray diffraction and scanning electron microscopy are carried out aiming to explain the ceramic behavior of each sample. The dielectric constants of different ceramics for both temperatures varied from 85.4 to 62.6, while their quality factor due to dielectric losses varied from 3110 to 1630. The Q decrease is attributed to the non uniform grain growth and to the obtained crystalline phases. The best microwave parameters were obtained for the ceramics sintered at 1400°C, which can be applied in microwave circuits as dielectric resonators. © (2010) Trans Tech Publications.

Influence of storage times on bond strength of resin cements to root canal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)