Non-contact specular microscopy in aphakic and pseudophakic dogs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Medidas de deslocamento e vibrações através de imagens de câmeras digitais

Pós-graduação em Engenharia Mecânica - FEIS

The influence of area/volume ratio on microstructure and non-Ohmic properties of SnO2-based varistor ceramic blocks

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Variação da temperatura corpórea em ovinos sob diferentes condições de manejo

Pós-graduação em Ciência Animal - FMVA

Output only based modal analysis of a reduced scale building using digital camera images

The article discusses a proposal of displacement measurement using a unique digital camera aiming at to exploit its feasibility for Modal Analysis applications. The proposal discusses a non-contact measuring approach able to measure multiple points simultaneously by using a unique digital camera. A modal analysis of a reduced scale lab building structure based only at the responses of the structure measured with the camera is presented. It focuses at the feasibility of using a simple ordinary camera for performing the output only modal analysis of structures and its advantage. The modal parameters of the structure are estimated from the camera data and also by using ordinary experimental modal analysis based on the Frequency Response Function (FRF) obtained by using the usual sensors like accelerometer and force cell. The comparison of the both analysis showed that the technique is promising noncontact measuring tool relatively simple and effective to be used in structural modal analysis

Moisture content and its influence on the roughness and noise emission during wood machining

Numerous factors influencing the surface quality of wood after machining, among them we highlight the machining parameters and the properties of the wood. In the analysis of the influence of these factors on machining and in determining the quality measurement systems are used to obtain surface characteristics, these systems are divided into methods of contact and non-contact. The method for mechanical contact performed with the aid of the surface roughness tester is the most valued in the measurement of roughness of wood, however, aiming at a greater agility in these measurements, there is a need to seek alternatives for evaluation of surface quality, and one of these options is to use the forms of indirect measurements of this quality, as for example, the use of noise emission during the machining process. With this, the aim was to analyze the influence of the moisture content of the wood, at different levels, on surface quality of the species Pinus elliottii, determined by the method of mechanical probing move and relate this roughness with the sound emission issued for each class of humidity, during machining. The planning of experiments and statistical analyses were performed with the help of Taguchi method. The specimens were conditioned in greenhouses climatizadoras automatics for obtaining three classes of humidity. Machining tests of wooden pieces were performed on a machining center specific for this type of material. The roughness values were measured by a roughness verifier and the noise emission values were measured by for a measurer sound pressure level. Statistically significant differences were observed, the significance level of 10 %, on roughness and noise emission between the three levels of moisture. It was observed that with the increase in the moisture content occurred an increase of roughness and a reduction in noise emission. Monitoring of surface quality through noise level is an interesting alternative to the method of mechanical contact.

Sorologia Anti PGL-1 e risco de ocorrência de hanseníase em área de alta endemicidade do Estado de São Paulo: quatro anos de seguimento

Os testes sorológicos para diagnóstico de hanseníase, usando o glicolipídeo-fenólico-1 (PGL-1), considerado antígeno específico do M. leprae, têm aberto algumas possibilidades de estudo do comportamento epidemiológico desta doença. Algumas questões, como tempo de latência da doença, infecção subclínica e importância do contato intra-domiciliar (contatos) no controle da endemia, puderam ser melhor analisadas usando este instrumental. Este estudo teve por objetivo verificar a existência de associação entre a situação sorológica e a ocorrência de hanseníase. Foram seguidas, durante 4 anos, 6.520 pessoas com idade igual ou superior a 5 anos, submetidas no início do seguimento ao teste sorológico Anti PGL-1, pertencentes ao universo de 7.416 habitantes da área urbana de um município paulista caracterizado por elevada endemicidade de hanseníase. Foi identificado um grupo de 590 indivíduos soropositivos (9,0 %). Foram diagnosticados, no período, 82 casos novos de hanseníase, 26 no grupo de soropositivos (441 casos novos/10.000 indivíduos) e 48 no de soronegativos (81/10.000). Entre os que não fizeram sorologia, surgiram 8 casos novos (89/10.000). Procurou-se controlar, na análise, a condição de contato, dado que a taxa de soropositividade padronizada por idade e sexo era de 9,61% no grupo de contatos e 7,65% no de não-contatos. Tomando-se os não-contatos soronegativos como o grupo de não expostos, foram calculados os riscos relativos de adoecimento no período, a partir das taxas de detecção padronizadas por idade, resultando no seguinte: os contatos ID soropositivos apresentaram a taxa de 1.704/10.000, 27 vezes maior que a dos não-expostos, igual a 63/10.000; os não-contatos soropositivos e os contatos soronegativos apresentaram taxas, respectivamente, de 274 e 198/10.000, ambas maiores que as dos não-expostos e iguais entre si. A soropositividade associou-se à elevação de 8,6 vezes do risco de hanseníase entre os contatos e de 4,4 entre os não-contatos. Na situação epidemiológica estudada, caracterizada por elevada endemicidade de hanseníase, 50% dos casos novos surgiram entre os não-contatos soronegativos, ou seja, sem fonte de infecção conhecida. Portanto, o teste anti-PGL-1 usado revela-se, na prática, de pouca aplicabilidade. Resta estudar ainda o comportamento da sorologia anti-PGL-1 em áreas de média e baixa endemicidade para que se possa tirar conclusões mais consubstanciadas sobre sua utilidade no controle da endemia. Recomenda-se o aprofundamento das pesquisas sorológicas e de outras que aprimorem o diagnóstico precoce da infecção subclínica, inclusive para detecção de formas paucibacilares, para se ampliar as possibilidades de influir no controle endêmico.

Phase-Locked loops lock-in range in Frequency Modulated-Atomic Force Microscope nonlinear control system

Since the mid 1980s the Atomic Force Microscope is one the most powerful tools to perform surface investigation, and since 1995 Non-Contact AFM achieved true atomic resolution. The Frequency-Modulated Atomic Force Microscope (FM-AFM) operates in the dynamic mode, which means that the control system of the FM-AFM must force the micro-cantilever to oscillate with constant amplitude and frequency. However, tip-sample interaction forces cause modulations in the microcantilever motion. A Phase-Locked loop (PLL) is used to demodulate the tip-sample interaction forces from the microcantilever motion. The demodulated signal is used as the feedback signal to the control system, and to generate both topographic and dissipation images. As a consequence, a proper design of the PLL is vital to the FM-AFM performance. In this work, using bifurcation analysis, the lock-in range of the PLL is determined as a function of the frequency shift (Q) of the microcantilever and of the other design parameters, providing a technique to properly design the PLL in the FM-AFM system. (C) 2011 Elsevier B.V. All rights reserved.

Effect of aging on the stability of ceramic foams prepared by thermostimulated sol-gel process

This work presents a new route of preparation of zirconium ceramic foams based on the thermostimulated sol-gel process. This method produces gelled bodies with up to 90% of porosity in the wet gel and can be used to make complex-shaped components. Unfortunately, the shrinkage during the drying step allows to a catastrophic reduction (50%) of the foam porosity. To improve the foam stability we carried out a systematic study of the effect of gel foam aging on the drying process. Samples were aged in closed vessel at 25 C during different time period (from 6 to 240 h). The shrinkage and the mass loss during drying at 50 C were measured in situ, using a non-contact technique performed with a special apparatus. The results show that the total linear shrinkage decreases from 46% to 8% as the aging period increase from 6 to 240 h. This behavior is followed by a small change of total mass loss, from 42 to 54%. It indicates that by aging the structural stiffness of the foams increases due to secondary condensation reactions. Thus, by controlling the aging period, the porosity can be increased from 67 to 75% and the average size of mesopores of dried foams can be screened from 0.3 to 0.9 mum. Finally, these results demonstrate that the thermostimulated sol-gel transition provides a potential route to ceramic foams manufacture.

Food restriction-induced myocardial dysfunction demonstrated by the combination of in vivo and in vitro studies

The aim of this study was to test the hypothesis that protein-calorie undernutrition decreases myocardial contractility jeopardizing ventricular function, and that ventricular dysfunction can be detected noninvasively. Five-month-old male Wistar-Kyoto rats were fed with regular rat chow ad libitum for 90 days (Control group, n = 14). A second group of rats received 50% of the amount of diet consumed by de control group (Food restricted group, n = 14). Global LV systolic function was evaluated in vivo, noninvasively, by transthoracic echocardiogram. After echocardiographic study, myocardial contractility was assessed in vitro in the isovolumetrically beating isolated heart in eight animals from each group (Langendorff preparation). The in vivo LV fractional shortening showed that food restriction depressed LV systolic function (p < 0.05). Myocardial contractility was impaired as assessed by the maximal rate of rise of LV pressure (+dP/dt), and developed pressure at diastolic pressure of 25 mmHg (p < 0.05). Furthermore, food restriction induced eccentric ventricular remodeling, and reduced myocardial elasticity and LV compliance (p < 0.05). In conclusion, food restriction causes systolic dysfunction probably due to myocardial contractility impairment and reduction of myocardial elasticity. © 2002 Elsevier B.V. All rights reserved.

On the nucleation of GaP/GaAs and the effect of buried stress fields

We have recently shown that spatial ordering for epitaxially grown InP dots can be obtained using the periodic stress field of compositional modulation on the InGaP buffer layer. The aim of this present work is to study the growth of films of GaP by Chemical Beam Epitaxy (CBE), with in-situ monitoring by Reflection High Energy Electron Diffraction (RHEED), on layers of unstressed and stressed GaAs. Complementary, we have studied the role of a buried InP dot array on GaP nucleation in order to obtain three-dimensional structures. In both cases, the topographical characteristics of the samples were investigated by Atomic Force Microscopy (AFM) in non-contact mode. Thus vertically-coupled quantum dots of different materials have been obtained keeping the in-place spatial ordering originated from the composition modulation. © 2006 Materials Research Society.

Variaciones del índice de cono en suelo movilizado posterior al tráfico de un tractor equipado con dos tipos de neumáticos y a cuatro velocidades de desplazamiento

The tractor is one of the machines that more traffics over the soil during the processes involving agricultural production. The interaction tractor/soil is made by the tires which, in most of the cases, are pneumatic. The tire type and the tractor travel speed, interfere directly on the pressure over the soil. One of the techniques employed to evaluate the alterations that tractor traffic causes in the soil is to measure its Cone Index. The aim of this research was to evaluate the same Cone Index alterations caused by an agricultural tractor equipped with both radial tires and bias ply tires, trafficking mobilized soil in four different travel speeds. The experiment was performed in a LATOSSOLO VERMELHO, located 22°51' S, 48°25'W and 770 m of altitude, in Botucatu-SP, Brazil. The soil mobilization was performed with a chisel plow and a disc arrow. The traction was accomplished with a John Deere tractor, model 6600, with 88 kW of power and 6,723 kg. Equipment requiring a force of 25kN was traced by the tractor draw bar. The experimental design was in randomized blocks with 4 × 2 factorial arrangements, with two distinct treatments corresponding to the types of tires (bias and radial) and the four travel speeds, with six replications. There were selected the following speeds: 3.5, 3.9, 5.1 and 5.9 km h-1. To determine the soil resistance, there was utilized MSSU - Mobile Soil Sampling Unit, with which the Cone Index was obtained in layers from 0-100, 100-200, 200-300, 300-400, 400-500 and over 500 mm deep. The Cone Index where evaluated in areas with non contact between tire and soil (ICn) and in the tire footprint track (ICp). There were calculated the Cone Index increments caused by the tractor tire (AIC) and the results showed that as the tractor travel speed increased, there were observed decrements in the medium values of cone index. The radial tire provided smaller values of the Cone Index in the superficial layer of the soil (0 to 100 mm) in relation to the bias ply tire, when the speed was approximately 6 km h-1. The increment in the Cone Index, promoted by the tractor, was more intense in the first 200 mm depth, but it also reached the layer from 200 to 300 mm.

Forced oscillations with continuum models of atomic force microscopy

The dynamics of the AFM-atomic force microscope follows a model based in a Timoshenko cantilever beam with a tip attached at the free end and acting with the surface of a sample. General boundary conditions arise when the tip is either in contact or non-contact with the surface. The governing equations are given in matrix conservative form subject to localized loads. The eigenanalysis is done with a fundamental matrix response of a damped second-order matrix differential equation. Forced responses are found by using a Galerkin approximation of the matrix impulse response. Simulations results with harmonic and pulse forcing show the filtering character and the effects of the tip-sample interaction at the end of the beam. © 2012 American Institute of Physics.

The thermal, rheological and structural properties of cassava starch granules modified with hydrochloric acid at different temperatures

Starch is arguably one of the most actively investigated biopolymer in the world. In this study, the native (untreated) cassava starch granules (Manihot esculenta, Crantz) were hydrolyzed by standard hydrochloric acid solution at different temperatures (30 °C and 50 °C) and the hydrolytic transformations were investigated by the following techniques: simultaneous thermogravimetry-differential thermal analysis (TG-DTA), differential scanning calorimetry (DSC), as well as non-contact atomic force microscopy (NC-AFM), X-ray diffraction (XRD) powder patterns, and rapid viscoamylographic analysis (RVA). After the treatment with hydrochloric acid at different temperatures, the thermal stability, a gradual loss of pasting properties (viscosity), alterations in the gelatinization enthalpy (ΔHgel), were observed. The use of NC-AFM and XRD allowed the observation of the surface morphology and topography of the starch granules and changes in crystallinity of the granules, respectively. © 2012 Elsevier B.V. All rights reserved.