Fabrication of Yb3+/Er3+ codoped Bi2O3-WO3-TeO2 pedestal type waveguide for optical amplifiers

We report, for the first time to our knowledge, experimental results on pedestal waveguides produced with Yb3+/Er3+ codoped Bi2O3-WO3-TeO2 thin films deposited by RF Sputtering for photonic applications. Thin films were deposited using Ar/O-2 plasma at 5 mTorr pressure and RF power of 40 W on substrates of silicon wafers. The definition of the pedestal waveguide structure was made using conventional optical lithography followed by plasma etching. Propagation losses around 2.0 dB/cm and 2.5 dB/cm were obtained at 633 and 1050 nm, respectively, for waveguides in the 20-100 mu m width range. Single-mode propagation was measured for waveguides width up to 10 mu m and 12 mu m, at 633 nm and 1050 nm, respectively; for larger waveguides widths multi-mode propagation was obtained. Internal gain of 5.6 dB at 1530 nm, under 980 nm excitation, was measured for 1.5 cm waveguide length (similar to 3.7 dB/cm). The present results show the possibility of using Yb3+/Er3+ codoped Bi2O3-WO3-TeO2 pedestal waveguide for optical amplifiers. (C) 2014 Elsevier B.V. All rights reserved.

Violet and blue light amplification in Nd3+-doped fluoroindate glasses

We report optical gain at 382 and 414 nm from Nd3+-doped fluroindate glasses after excitation with lasers operating either at 583 or 532 nm. Stimulated emission due to a frequency upconversion process results in increase of the emitted violet and blue light intensity and emission line narrowing. Large optical gain is measured by pump-probe spectroscopy using samples with various Nd3+ concentrations. © 1999 American Institute of Physics.

Vertical variation in autumn leaf phenology of Fagus sylvatica L. in southern Germany

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Um Modelo para Análise do Balanço e Eficiência Energética na Logística de Transporte Dutoviário para Exportação do Etanol.

This paper analyzed the energy flow of a route currently designed to transport ethanol from the Midwest region of Brazil for exportation, more precisely from the city of Aparecida do Taboado (MS) to the port of São Sebastiao (SP). The route studied a single modal combined into two pieces, duct - duct. The direct and indirect energy, involved in the operations were used to account for the inputs and outputs of energy from and into the system. The energy input and output were the variables, diesel fuel, lubricants, greases, indirect energy consumption of machinery and equipment, power consumption of labor, the energy consumption and energy consumption in depreciation and maintenance of roads. We found that this route has specific energy consumption of 0,14 MJ km-1 m-3 . The Net Energy Gain (GEl), the Energy Efficiency global (EEg) and Renewable Energy Balance (BEr), which were the energy indicators adopted in this study were obtained respectively: 1.585.958.977,00 MJ; 200,72 and 1.593.900.000,00MJ.

Design of a simple detection cell with extended optical path length for capillary electrophoresis: Application to multiresidue pesticide analysis

Absorbance detection in capillary electrophoresis (CE), offers an excellent mass sensitivity, but poor concentration detection limits owing to very small injection volumes (normally I to 10 nL). This aspect can be a limiting factor in the applicability of CE/UV to detect species at trace levels, particularly pesticide residues. In the present work, the optical path length of an on-column detection cell was increased through a proper connection of the column (75 mu m i.d.) to a capillary detection cell of 180 mu m optical path length in order to improve detectability. It is shown that the cell with an extended optical path length results in a significant gain in terms of signal to noise ratio. The effect of the increase in the optical path length has been evaluated for six pesticides, namely, carbendazim, thiabendazole, imazalil, procymidone triadimefon, and prochloraz. The resulting optical enhancement of the detection cell provided detection limits of ca. 0.3 mu g/mL for the studied compounds, thus enabling the residue analysis by CE/UV.

Net and metabolizable protein requirements for body weight gain in hair and wool lambs

Protein is one of the limiting factors in animal production, and the knowledge of protein requirements by livestock is crucial for the success of a commercial animal raising enterprise. Thirty-four castrated lambs, 17 of them F1 Ideal x lie de France wool lambs and the remaining ones were Santa Ines hair lambs, with homogeneous initial BW, were used in the experiment. Five animals from each genotype were slaughtered in the beginning of the experimental period and used as reference. Diets (D) were composed of concentrate mix (C) and Cynodon sp. c.v. Tifton 85 hay (R), combined in three different ratios: D1 =60CAOR; D2=40C:60R and D3=20C:80R. Animals of each group of three lambs, that showed simultaneously an initial BW of 20 +/- 0.14 kg at the beginning of the dietary regimen, were slaughtered when one of them reached 35 kg, what always happened to be the one fed with D1. Net requirements for BW gain in wool lamb, fleece-free, ranged from 101 to 110 g of protein/kg BW, and for hair lamb ranged from 1 10 to 118 g of protein/kg BW. Net protein requirements for wool production ranged from 634 to 642 g/kg of produced wool. Hair lambs presented a 7.8-9.5% higher estimated net protein requirements than wool lambs, according to BW and daily weight gain (DG). Total net protein requirements for Santa Ines and wool lambs, with 30 kg of initial B W and an approximate 200 g mean DG, were 48.5 and 45.4 g/day, respectively. Metabolizable protein requirements for Santa Ines and wool lambs, with 20 kg of initial BW and an approximate 200 g mean DG were 59.4 g and 76.5 -/day, respectively. Net protein requirements for wool production was 64g/100g of produced wool. Thus, under the conditions of this experiment, it is concluded that hair lambs showed a higher concentration of protein in the body, more efficient use of the ingested protein and a consequent additional BW gain when fed isoproteic diets as compared to F1 Ideal x Ile de France wool lambs. (c) 2006 Elsevier B.V All rights reserved.

Correlation between structural and electronic order-disorder effects and optical properties in ZnO nanocrystals

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparative analysis between a CAD model design and physical models obtained by manufacturing additive technologies using optical scan

This article presents a detailed study of the application of different additive manufacturing technologies (sintering process, three-dimensional printing, extrusion and stereolithographic process), in the design process of a complex geometry model and its moving parts. The fabrication sequence was evaluated in terms of pre-processing conditions (model generation and model STL SLI), generation strategy and physical model post-processing operations. Dimensional verification of the obtained models was undertook by projecting structured light (optical scan), a relatively new technology of main importance for metrology and reverse engineering. Studies were done in certain manufacturing time and production costs, which allowed the definition of an more comprehensive evaluation matrix of additive technologies.

Estimates of genetic parameters for visual scores and daily weight gain in Brangus animals

(Co) variance components were estimated for visual scores of conformation (CY), early finishing (PY) and muscling (MY) at 550 days of age (yearling), average daily gain from weaning to yearling (GWY), conformation (CW), early finishing (PW) and muscling (MW) scores at weaning, and average daily gain from birth to weaning (GBW) in animals forming the Brazilian Brangus breed born between 1986 and 2002 from the livestock files of GenSys Consultants Associados S/C Ltda. The data set contained 53 683; 45 136; 52 937; 56 471; 24 531; 21 166; 24 006 and 25 419 records for CW, PW, MW, GBW, CY, PY, MY and GWY, respectively. Data were analyzed by the restricted maximum likelihood method using single-and two-trait animal models. Direct heritability estimates obtained by single-trait analysis were 0.12, 0.14, 0.13 and 0.14 for CY, PY and MY scores and GWY, respectively. A positive association was observed between the same visual scores at weaning and yearling, with correlations ranging from 0.64 to 0.94. Estimated correlations between GBW and weaning and yearling scores ranged from 0.60 to 0.77. The genetic correlation between GBW and GWY was low (0.10), whereas correlations of 0.55, 0.37 and 0.47 were observed between GWY and CY, PY and MY, respectively. Moreover, GWY showed a weak correlation with CW (0.10), PW (-0.08) and MW (-0.03) scores. These results indicate that selection of the traits that was studied would result in a small response. In addition, selection based on average daily gain may have an indirect effect on visual scores as the correlations between GWY and visual scores were generally strong.

Suckling and allosuckling in river buffalo calves and its relation with weight gain

The aim of the present study was to investigate if river buffalo calves (Bubalus bubalis) have equal access to all cows and if milk is thus equally available to all of them. We recorded suckling/allosuckling behaviour and weight gain (WG) of 29 calves (14 males and 15 females), with special consideration to their sex, birth order (BO) and age. Cows' nursing behaviour and milli production (MP) were also considered. While males tended to be born earlier than females during this study, this was not the trend in the overall herd records. The cows' MP was not effected by the calves' sex. However, bull-calves presented greater mean WG, and mean times spent in individual filial (IF) and in communal nonfilial (CNF) suckling than heifer-calves, which showed greater communal filial (CF) suckling than the former during the first 4 months of life. The WG was associated with IF for bull-calves (r = 0.680 and 0.765, respectively, for the periods from birth to 4th and 8th months of age), and to CNF for heifer-calves (r = 0.628, for the period from birth to 8th month). Results from multiple regression analysis showed independent effects of each suckling category on the calf WG, and such effects were variable according to the calf's sex. BO was negatively correlated to calves' WG (bull-calves: r(s) = - 0.873 and - 0.799, from birth to 4th and gth months, respectively; heifer-calves: r(s) = - 0.531 from birth to 4th month). Specifically for bull-calves, there was a positive correlation between BO and MP (r(s) = 0.528 and 0.633, from birth to 4th and 8th months of age, respectively). The correlation between BO and IF was negative in both sexes, indicating that calves that were born early had more opportunities to suckle individually from their mothers. For heifer-calves, BO was positively correlated with CF (two periods), and negatively with CNF (from birth to 8th month of age), suggesting that heifer-calves were most often accompanied by other calves during suckling when they were born later. The data taken together indicate that sex and/or BO influenced decisively social interactions during suckling, promoting differential development among the calves. In animal husbandry, if a homogenous WG is desired, these factors have to be taken into consideration. (C) 2000 Elsevier B.V. B.V. All rights reserved.

Prediction equations to estimate the demand of energy and crude protein for maintenance, gain and egg production for laying Japanese quails

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Prediction of intake and average daily gain by different feeding systems for goats

A main purpose of a mathematical nutrition model (a.k.a., feeding systems) is to provide a mathematical approach for determining the amount and composition of the diet necessary for a certain level of animal productive performance. Therefore, feeding systems should be able to predict voluntary feed intake and to partition nutrients into different productive functions and performances. In the last decades, several feeding systems for goats have been developed. The objective of this paper is to compare and evaluate the main goat feeding systems (AFRC, CSIRO, NRC, and SRNS), using data of individual growing goat kids from seven studies conducted in Brazil. The feeding systems were evaluated by regressing the residuals (observed minus predicted) on the predicted values centered on their means. The comparisons showed that these systems differ in their approach for estimating dry matter intake (DMI) and energy requirements for growing goats. The AFRC system was the most accurate for predicting DMI (mean bias = 91 g/d, P < 0.001; linear bias 0.874). The average ADG accounted for a large part of the bias in the prediction of DMI by CSIRO, NRC, and, mainly, AFRC systems. The CSIRO model gave the most accurate predictions of ADG when observed DMI was used as input in the models (mean bias 12 g/d, P < 0.001; linear bias -0.229). while the AFRC was the most accurate when predicted DMI was used (mean bias 8g/d. P > 0.1; linear bias -0.347). (C) 2011 Elsevier B.V. All rights reserved.

Genetic parameters and relationships of heifer pregnancy and age at first calving with weight gain, yearling and mature weight in Nelore cattle

The objectives of the current study were to investigate the additive genetic associations between heifer pregnancy at 16 months of age (HP16) and age at first calving (AFC) with weight gain from birth to weaning (WG), yearling weight (YW) and mature weight (MW), in order to verify the possibility of using the traits measured directly in females as selection criteria for the genetic improvement of sexual precocity in Nelore cattle. (Co)variance components were estimated by Bayesian inference using a linear animal model for AFC, WG, YW and MW and a nonlinear (threshold) animal model for HP16. The posterior means of direct heritability estimates were: 0.45 +/- 0.02; 0.10 +/- 0.01; 023 +/- 0.02; 0.36 +/- 0.01 and 0.39 +/- 0.04, for HP16, AFC, WG, YW and MW, respectively. Maternal heritability estimate for WG was 0.07 +/- 0.01. Genetic correlations estimated between HP16 and WG, YW and MW were 0.19 +/- 0.04; 0.25 +/- 0.06 and 0.14 +/- 0.05, respectively. The genetic correlations of AFC with WG, YW and MW were low to moderate and negative, with values of -0.18 +/- 0.06; -0.22 +/- 0.05 and -0.12 +/- 0.05, respectively. The high heritability estimated for HP16 suggests that this trait seem to be a better selection criterion for females sexual precocity than AFC. Long-term selection for animals that are heavier at young ages tends to improve the heifers sexual precocity evaluated by HP16 or AFC. Predicted breeding values for HP16 can be used to select bulls and it can lead to an improvement in sexual precocity. The inclusion of HP16 in a selection index will result in small or no response for females mature weight. (C) 2011 Elsevier B.V. All rights reserved.

Genetic parameter estimates for live weight and daily live weight gain obtained for Nellore bulls in a test station using different models

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dependence of the electrical conductivity and elastomeric properties on sample preparation of blends of polyaniline and natural rubber

Blend films (free-standing) containing 20% in volume of polyaniline (PANI) in 80% of natural rubber (NR) were fabricated by casting in three different ways: (1) adding PANI-EB (emeraldine base) dissolved in N-methyl-2-pyrrolidone (NMP) to the latex (NRL), (2) adding PANI-EB dissolved in in-cresol to NR dissolved in xylol (NRD), (3) overlaying the surface of a pure NR cast film with a PANI layer grown by in situ polymerization (NRO). All the films were immersed into HCl solution to achieve the primary doping (protonation) of PANI before the characterization. The main goal here was to investigate the elastomeric and electrical conductivity properties for each blend, which may be applied as pressure and deformation sensors in the future. The characterization was carried out by optical microscopy, dc conductivity, vibrational spectroscopy (infrared absorption and Raman scattering), thermogravimetry analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile stress-strain curves. The results suggest that the NRL blend is the most suitable in terms of mechanical and electrical properties required for applications in pressure and deformation sensors: a gain of conductivity without losing the elastomeric property of the rubber. (c) 2005 Wiley Periodicals, Inc.