Production of an axial piston: Impacts resulting from the substitution of steel by a polymer-based material

The substitution of steel as a raw material in the production of axial pistons for pressure washers by polyphthalamide, polytetrafluoroethylene and glass fiber-based composite was studied. The new production process with composite consists of only two steps, while the production of the steel piston is to comprise of thirteen steps. This replacement would result in an estimated reduction of 80% of water consumption, 83% of electricity consumption, 73% of the total cost and 88% of the final mass. With regard to the main mechanical properties required for the end product, the composite was found to withstand the critical axial loads and it shows acceptable wear resistance in an environment without lubrication, an additional advantage of this replacement. © 2012 Elsevier Ltd. All rights reserved.

Tamanho de amostra e estimativa de custo em levantamento epidemiológico de cárie dentária

This study aimed to analyze how the prevalence and the distribution of dental caries influence the sample size in epidemiological surveys, and how much are the costs. Secondary data of oral health surveys in 12-year-old schoolchildren from Bauru in 1976, 1984, 1990, 1994, and 2001, and from Piracicaba in 2001 and 2005 were studied. Sample sizes were estimated taking into account the mean DMFT and standard deviation of each survey, establishing sampling errors of 1%, 2%, 5%, and 10%. Costs were estimated considering permanent material, consumption material and human resources. The sample size in both towns needed to be increased, ranging from 119 in 1976 to 1,118 in 2001 in Bauru, and from 954 in 2001 to 1,252 in 2005 in Piracicaba, when a sampling error of 10% was considered. The cost of dental caries surveys was verified considering different sampling errors. This cost depends on how acceptable is the margin of difference between the true mean and the one found in the survey. In conclusion, the reduction in the prevalence of dental caries has determined the need for increase in sample size and in costs for conducting the surveys.

Efeito do genótipo e do teor protéico da dieta na resistência de cordeiros à hemoncose experimental

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação da Polpa de Citros Peletizada como Material para Cama de Frangos de Corte

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Material de cama: qualidade, quantidade e efeito sobre o desempenho de frangos de corte

An experiment was conducted to evaluate performance, mortality and incidence of lesions on the breasts, hooks and foot pads of broilers raised on wood-scrap litter, rice hulls, Brachiaria hey (Brachiaria decumbens), Napier hay (Pennisetum purpureum) and Coast-cross hay (Cynodon dactylon). A randomized experimental design with five litters, two sexes, four replications and fifty birds per box was used. A standard litter height of 5 cm of wood-scraps and a weight of 20 250 g were adopted as criteria for use of other materials in the boxes. The amount of excreta deposited was 1697 g per raised bird (34,00 % of feed consumption). The incidence of lesions was evaluated in five birds per box after 35, 42 and 49 days and after slaughter. The criteria for scoring lesions were: 0 = without lesion; 1 = inflammation; 2 = mild ulceration; 3 = severe ulceration. At the end of experimental period (49 days) no differences were observed For weight, weight gain, feed consumption, feed/gain ratio and mortality among treatments. The lesions of the hocks and foot pads of the birds, raised on either Coast-cross hay and Napier hay, were more severe than those on wood-scraps and Brachiaria hay. Males showed better performance than females, but their hock lesions were more severe, independent of the litter used. Based on the performance and lesions scores, it was concluded that Braquiaria hay could be used as litter in replace wood-scraps and rice bulls.

Characteristics of Dielectric Barrier Discharge Reactor for Material Treatment

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Biomass fire consumption and carbon release rates of rainforest-clearing experiments conducted in northern Mato Grosso, Brazil

Biomass consumption and carbon release rates during the process of forest clearing by fire in five test plots are presented and discussed. The experiments were conducted at the Caiabi Farm near the town of Alta Floresta, state of Mato Grosso, Brazil, in five square plots of 1 ha each designated A, B, C, D, and E, with different locations and timing of fire. Plot A was located in the interface with a pasture, with three edges bordering on the forest, and was cut and burned in 1997. Plots B,C, D, and E were located inside the forest. Plot B was cut and burned in 1997. Plot C was inside a deforested 9-ha area, which was cut and burned in 1998. Plot D was inside a deforested 4-ha area, which was cut in 1998 and burned in 1999. Plot E was inside a deforested 4-ha area which was cut and burned in 1999. Biomass consumption was 22.7%, 19.5%, 47.5%, 61.5% and 41.8%, for A, B, C, D, and E, respectively. The effects of an extended curing period and of increasing the deforested area surrounding the plots could be clearly observed. The consumption for areas cut and burned during the same year, tended toward a value of nearly 50% when presented as a function of the total area burned. The aboveground biomass of the test site and the amount of carbon before the fire were 496 Mg ha-1 and 138 Mg ha-1, respectively. Considering that the biomass that remains unburned keeps about the same average carbon content of fresh biomass, which is supported by the fact that the unburned material consists mainly of large logs and considering the value of 50% for consumption, the amount of carbon released to the atmosphere as gases was 69 Mg ha-1. The amounts of CO2 and CO released to the atmosphere by the burning process were then estimated as 228 Mg ha-1 and 15.9 Mg ha-1, respectively. Observations on fire propagation and general features of the slash burnings in the test areas complete the paper. Copyright 2001 by the American Geophysical Union.

Occupational exposure to paint solvents and particulate material in car repair shops

Aims: We evaluated solvents and total particulates exposures in auto body repair shops together with a search of painter's related complaints. Methods: 26 painters exposures were evaluated by pumped personal sampling; solvents were retained in charcoal sorbent tubes and the particulates in PVC filters. Painter's personal habits and their work characteristics were obtained through a questionnaire, applied in a private interview. For the symptoms the Q16 questionnaire was used, added of questions about complaints during the painting. Results: High exposures were detected during spray painting. For solvents, the TLV-STEL adjusted for the mixtures was surpassed in six evaluations. However, as repaint is a short-term operation, it makes the average concentrations weighed for the work shift lower than the TLV-TWA adjusted for the mixtures. Total particulate concentrations had surpassed the TLV-TWA in four of the evaluations. Symptoms frequency in the Q16 questionnaire was higher for painters than for the controls (Mann-Whitney test U=193; p=0.008), and they showed positive correlations with the age (Spearman r=0.354, t=1.85, p=0.076), the number of years in the profession (Spearman r=0.433, t=2.35, p=0.027) and the alcoholic beverage consumption (Spearman r=0.457, t=2.516, p=0.019). Conclusions: The painting work done at car repair shops can result in high solvent and particulate exposures, although they are short-term operations. Their acute and chronic effects for the painters do not have been clearly evidenced in the present study, continuing deserving multidisciplinary attention.

Avaliação experimental de um sistema não linear para extração de energia através de vibrações utilizando material piezelétrico

Pós-graduação em Engenharia Mecânica - FEIS

An innovative material based on natural rubber and leather tannery waste to be applied as antistatic flooring

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chemical weathering rate, denudation rate, and atmospheric and soil CO2 consumption of Parana flood basalts in Sao Paulo State, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Diagnóstico laboratorial de Mycobacterium spp. em Botucatu e região, utilizando a técnica Reação em Cadeia da Polimerase (PCR) em material biológico e avaliação de condições associadas

Pós-graduação em Saúde Coletiva - FMB

Características estruturais e físicas de material biodegradável produzido a base de zeína e fibras de milho e bananeira

Pós-graduação em Engenharia e Ciência de Alimentos - IBILCE