Properties advanced of the silicon nitride based ceramics and recent performance on automotive parts manufacture by machining process: Advanced Ceramics, demand Forecast

Automotive parts manufacture by machining process using silicon nitride-based ceramic tool development in Brazil already is a reality. Si 3N4-based ceramic cutting tools offer a high productivity due to their excellent hot hardness, which allows high cutting speeds. Under such conditions the cutting tool must be resistant to a combination of mechanical, thermal and chemical attacks. Silicon nitride based ceramic materials constitute a mature technology with a very broad base of current and potential applications. The best opportunities for Si3N 4-based ceramics include ballistic armor, composite automotive brakes, diesel particulate filters, joint replacement products and others. The goal of this work was to show latter advance in silicon nitride manufacture and its recent evolution on machining process of gray cast iron, compacted graphite iron and Ti-6Al-4V. Materials characterization and machining tests were analyzed by X-Ray Diffraction, Scanning Electron Microscopy, Vickers hardness and toughness fracture and technical norm. In recent works the authors has been proved to advance in microstructural, mechanical and physic properties control. These facts prove that silicon nitride-based ceramic has enough resistance to withstand the impacts inherent to the machining of gray cast iron (CI), compacted graphite iron (CGI) and Ti-6Al-4V (6-4). Copyright © 2008 SAE International.

Moisture content and its influence on the roughness and noise emission during wood machining

Numerous factors influencing the surface quality of wood after machining, among them we highlight the machining parameters and the properties of the wood. In the analysis of the influence of these factors on machining and in determining the quality measurement systems are used to obtain surface characteristics, these systems are divided into methods of contact and non-contact. The method for mechanical contact performed with the aid of the surface roughness tester is the most valued in the measurement of roughness of wood, however, aiming at a greater agility in these measurements, there is a need to seek alternatives for evaluation of surface quality, and one of these options is to use the forms of indirect measurements of this quality, as for example, the use of noise emission during the machining process. With this, the aim was to analyze the influence of the moisture content of the wood, at different levels, on surface quality of the species Pinus elliottii, determined by the method of mechanical probing move and relate this roughness with the sound emission issued for each class of humidity, during machining. The planning of experiments and statistical analyses were performed with the help of Taguchi method. The specimens were conditioned in greenhouses climatizadoras automatics for obtaining three classes of humidity. Machining tests of wooden pieces were performed on a machining center specific for this type of material. The roughness values were measured by a roughness verifier and the noise emission values were measured by for a measurer sound pressure level. Statistically significant differences were observed, the significance level of 10 %, on roughness and noise emission between the three levels of moisture. It was observed that with the increase in the moisture content occurred an increase of roughness and a reduction in noise emission. Monitoring of surface quality through noise level is an interesting alternative to the method of mechanical contact.

Influência na qualidade final de metais retificados através da variação da velocidade de mergulho

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo entre a agressividade superficial obtida na retificação com rebolos de óxido de alumínio e CBN, fabricados com ligantes resinóide e vitrificado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência da velocidade de avanço do rebolo nos danos de aços endurecidos retificados

A tendência mundial é o aumento da produtividade e da produção de peças cada vez mais sofisticadas, com elevado grau de tolerância geométrica, dimensional, com bom acabamento superficial, com baixo custo. A retificação é responsável pelo acabamento final no processo de usinagem de um material. No entanto, danos gerados nesta fase de produção comprometem todos os recursos utilizados nas fases anteriores. Grande parte dos problemas ocorridos na retificação deve-se à enorme temperatura gerada pelo processo devido às condições de usinagem. Atribui-se à velocidade de avanço, que está diretamente relacionada com a produtividade, os danos ocorridos na retificação, ficando esta variável limitada até valores que não proporcione danos. Neste trabalho, através da variação da velocidade de avanço no processo de retificação cilíndrica externa do aço ABNT D6, racionalizando a aplicação de dois fluidos de corte e usando um rebolo superabrasivo de CBN (nitreto de boro cúbico) com ligante vitrificado, avaliou-se a influência da velocidade de avanço nos danos superficiais de aços endurecidos. Os resultados permitiram concluir que a velocidade de avanço associada a uma eficiente refrigeração e lubrificação, não provocou danos térmicos (queima, trincas, tensões de tração) ao material. Tensões residuais e a rugosidade do material retificado apresentaram uma correlação com as condições de usinagem. O trabalho concluiu ser capaz um aumento dos índices de produtividade sem provocar danos nos componentes retificados.

Influence of the grinding wheel's dive speed on the damage of rectified hardened steels

The world tendency is the increase of the productivity and the production of pieces more and more sophisticated, with high degree of geometric and dimensional tolerances, with good surface finish and low cost. Rectification is responsible for the final finish in the machining process of a material. However, damages generated in this production phase affect all the resources used in the previous processes. Great part of the problems happennig in the rectification process is due to the enormous temperature generated in this activity because of the machining conditions. The dive speed, which is directly related to the productivity, is considered responsible for the damages that occur during rectification, limiting its values to those that do not cause such damages. In this work, through the variation of the dive speed in the process of cylindrical grinding of type ABNT D6 steel, rationalizing the application of two cutting fluids and using a CBN (cubic boron nitrate) abrasive wheel with vitrified blond, the influence of the dive speed on the surface damages of hardened steels was evaluated. The results allowed to say that the dive speed, associated to an efficient cooling and lubrication, didn't provoke thermal damages (including heated zones, cracks and tension stresses) to the material. Residual stresses and the roughness of rectified materials presented a correlation with the machining conditions. The work concluded that it is possible to increase the productivity without provoking damages in the rectified components.

Estudo comparativo do desempenho de rebolos com grãos superabrasivos e convencionais

Grinding is a precision machining process which is widely used in the manufacture of components requiring fine tolerances and smooth surfaces. There are several imput parameters (cutting conditions, cutting fluid and grinding wheel type used, dressing conditions etc.) which can affect the process variables (tangential and normal cutting forces, roughness, grinding temperatures, G ratio, etc.) leading to differences in the roughness, in the surface integrity and in the mechanical strength of the ground component. Consequently, the imput parameters must be controlled in order to insure the workpiece final quality. This paper presents a comparative evaluation of the performance of two types of grinding wheels [a conventional (Al2O3) and a superabrasive (CBN)] when grinding a VC131 steel, by the analysis of specific process variables when varying the cutting conditions. Highest values of G ratio and lowest workpiece roughness was observed when using CBN grinding wheels. This confirms the global trend of replacement of alumina grinding wheels by CBN, when grinding DTG (difficult to grind) materials.

Grinding of hardened steels using optimized cooling

Grinding - the final machining process of a workpiece - requires large amounts of cutting fluids for the lubrication, cooling and removal of chips. These fluids are highly aggressive to the environment. With the technological advances of recent years, the worldwide trend is to produce increasingly sophisticated components with very strict geometric and dimensional tolerances, good surface finish, at low costs, and particularly without damaging the environment. The latter requirement can be achieved by recycling cutting fluids, which is a costly solution, or by drastically reducing the amount of cutting fluids employed in the grinding process. This alternative was investigated here by varying the plunge velocity in the plunge cylindrical grinding of ABNT D6 steel, rationalizing the application of two cutting fluids and using a superabrasive CBN (cubic boron nitride) grinding wheel with vitrified binder to evaluate the output parameters of tangential cutting force, acoustic emission, roughness, roundness, tool wear, residual stress and surface integrity, using scanning electron microscopy (SEM) to examine the test specimens. The performance of the cutting fluid, grinding wheel and plunge velocity were analyzed to identify the best machining conditions which allowed for a reduction of the cutting fluid volume, reducing the machining time without impairing the geometric and dimensional parameters, and the surface finish and integrity of the machined components.

Estimação do diâmetro e rugosidade em um processo de furação utilizando multi sensores e redes neurais artificiais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização de técnicas do planejamento de experimentos na otimização de um processo de torneamento da superliga NIMONIC 80A

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desempenho do stellite como material de ferramenta no serramento da madeira

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do uso de ferramentas cerâmicas na usinagem de inconel 718

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelagem térmica para avaliação da temperatura no fresamento de aços para moldes e matrizes

Pós-graduação em Engenharia Mecânica - FEIS

Portaferramentas para torneamento com refrigeração interna baseada na mudança de fase do fluido

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Otimização da retificação tangencial plana de compósitos plásticos reforçados com fibras de carbono

Pós-graduação em Ciência e Tecnologia de Materiais - FC