An investigation of pile diameter influence in the bearing capacity on Dynamic Load Test (DLT)

During the construction of five residential buildings in the city of Taubate, State of São Paulo, it was possible to carry out one comprehensive investigation of the behavior of precast concrete piles in clay shales. This paper describes the results of Dynamic Load Tests (DLT's) executed in three piles with different diameters and with the same embedded length. The tests were monitored using the PDA(R) (Pile Driving Analyzer) and the pile top displacement was measured by pencil and paper procedure. From the curves of RMX versus DMX resulted from CASE(R) method, CAPWAPC(R) analyses were made for signals where the maximum mobilized soil resistance was verified. The results were compared with the predicted bearing capacity using the semi-empirical method of Decourt & Quaresma (1978) and Decourt (1982) based on SPT values and the description of the soil profile. Some comments related to the values of quake and damping used for clay shales in the analyses are also presented.

Atributos físicos do solo em áreas de plantio direto com e sem escarificação

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Capacidade de suporte de carga e densidade do solo em áreas de plantio direto com e sem escarificação

No-till has been used in many different regions of Brazil. However, depending on the location and intensity of machinery traffic, this has caused the problem of soil compaction and many producers are scarification the land as a solution to break through the layer that is restricting plant growth. The objective of this study was to evaluate the influence of scarification (0.30 m) in the physical properties of a dystrophic Alfisol comparing the results with a non-scarified contiguous area; both were previously conducted using no-till. The density and pressure of pre-consolidation were sampled in two areas of non-tillage, one with chiseling (PDCE) and one without (PDSE) by using the UMAS -Mobile Soil Sampling Unit built by NEMPA – Agroforestry Machinery and Tire Testing Center/FCA / UNESP, Botucatu ,SP. The UMAS is equipped with GPS which allows the samples to be georeferenced. The samples were evaluated in the laboratory through the collection of standardized rings. Sampling was performed at a dimension of 15 x 50 m, with 160 rings being collected. The samples containing rings which were used in determining the density and also for testing the consolidometer, were collected from the layers of 0 to 0.10 m, 0.10 to 0.20 m, 0.20 to 0.30 0.30 to I 0.40 m. For the odometer test the undisturbed sample rings were used in obtaining the load bearing capacity of the soil. The soil management adopted provided a decrease in soil density using no-tillage with scarification depths from 0.0 to 0.10 0.10 to 0.20 m while the other depths did not show any decrease. The pre-consolidation pressure in combination with soil aggregate resistance identified that the management process PDCE within all layers was subjected to water content reliability regarding a greater load bearing capacity of the soil. For the PDSE that only was possible in the 0 to 0.10 m, showing greater consolidation of this layer.

Parâmetros geotécnicos e previsão da capacidade de carga de estacas apiloadas em solo tropical arenoso obtidos com o Pressiômetro Ménard

This paper presents and discusses Ménard Pressuremeter test results used to predict bearing capacity of pounded piles installed in a tropical sandy soil. Fifteen pre-bored pressuremeter tests were carried out at the Experimental Research Site from Unesp - Bauru up to 15 m depth, one test per meter. Several laboratory and in situ tests were carried out in this research site as well as load tests on plates and on piles. Pressuremeter test results were firstly analyzed to determine geotechnical soil parameters based on empirical methods, emphasizing the estimative of the earth pressure coefficient at rest (K0). After that, bearing capacity prediction of pounded piles with 4 m, 7 m and 10 m were made and compared with test results from instrumented load tests. Pressuremeter test results allowed a very good estimative of bearing capacity for the pile with 4 m length and underestimated in 25,7% and 20,0% the bearing capacity for the pile with 7 and 10 m length, respectively. The back analysis of the test results suggests that the appropriate value for the bearing capacity factor for the tested soil-pile system on this soil is equal to 2.

Electromyographic analysis of the pectoralis major and deltoideus anterior in the inclined flying exercise with loads

Due to a shortage of textbooks with specific data on muscular activity concerning physical conditioning and sports, we analysed electromyographically the muscles pectoralis major and deltoideus anterior, bilaterally, in inclined flying exercises, during the concentric and eccentric phases, with external loads of 25, 50, 75 and 100% of the maximum load. The electromyographic analysis was performed in eleven male volunteers with MEDITRACE-200 surface electrodes connected to a six-channel biologic signal acquisition module coupled to a PC/AT computer. The electromyographic signals were processed and the obtained effective values were normalized through maximum voluntary isometric contraction. Statistically, the results showed that all the muscles studied presented significant differences between the concentric and the eccentric phases, with higher electromyographic activity during the concentric phase. By analysing the different loads for each muscle in both phases, significant electromyographic activity was observed for all muscles. When the effect of each load on each muscle during the concentric phase was analysed, it was noticed that the muscles on the left were more active than those on the right side, while in the eccentric phase the muscles had different behavior.

Determination of soil properties from standard penetration test complemented by torque measurement (SPT-T)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Previsão da capacidade de carga de estacas escavadas em solo arenoso da região de Araquari-SC

In Geotechnical engineering the foundation projects depend on the bearing capacity and the acceptable displacements. One of the possible ways to predict the bearing capacity of foundations is through semi-empirical statistical methods which correlate in-situ tests (SPT and CPT). The piles breaking loads are defined by the interpretation of the load x head displacement curve and the experimental data acquired through the load test. In this work it is studied the behavior of bored piles executed in the Araquari/SC region, comparing the bearing capacity values predicted by the methods DECOURT & QUARESMA MODIFICADO (1996), AOKI & VELLOSO MODIFICADO MONTEIRO (2000), MILITITISKY E ALVES (1985), DECOURT & QUARESMA (1978), MÉTODO DE AOKI & VELLOSO (1975) e PHILOPANNAT (1986), with the results of the load test, evaluating their differences and discussing parameters that have direct effects on the prediction

Avaliação da compressibilidade de um Nitossolo Vermelho distroférrico sob sistema plantio direto, preparo convencional e mata nativa

Os efeitos do tráfego de máquinas nos atributos do solo de acordo com o tempo de adoção do sistema plantio direto são ainda pouco pesquisados em ambientes tropicais, e muitas dúvidas ainda persistem sobre a variação dinâmica da estrutura do solo e a sua interação com máquinas e equipamentos. Objetivou-se com este estudo avaliar o efeito do tempo de adoção do sistema plantio direto, comparativamente com área de mata nativa e de preparo convencional, usando os modelos de compressibilidade do solo. O estudo foi realizado em um Nitossolo Vermelho distroférrico, sob mata nativa (MN), preparo convencional (PC), plantio direto com um ano (PD1), plantio direto com quatro anos (PD4), plantio direto com cinco anos (PD5) e plantio direto com 12 anos (PD12). Amostras indeformadas e deformadas foram coletadas em duas profundidades (0-5 e 10-15 cm). O tempo de adoção do sistema plantio direto alterou o comportamento compressivo dos solos em ambas as profundidades, por meio das mudanças na pressão de preconsolidação. A profundidade de 0-5 cm apresentou menor capacidade de suporte de carga do que a profundidade de 10-15 cm. A profundidade de 0-5 cm, em todos os sistemas de manejo, mostrou-se mais susceptível à compactação em relação à profundidade de 10-15 cm. Os sistemas de plantio direto e convencional apresentaram a capacidade de suporte de carga crescente na seguinte ordem: PD5 < PD12 < PD1 < PD4 @ PC, para a profundidade de 0-5 cm e para a profundidade de 10-15 cm: MN @ PD12 < PC @ PD4 < PD5, enquanto o sistema PD1 apresentou comportamento diferenciado.

Influence of Implant Design on the Biomechanical Environment of Immediately Placed Implants: Computed Tomography-Based Nonlinear Three-Dimensional Finite Element Analysis

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Consolidômetro: equipamento pneumático-eletrônico para avaliação do estado de consolidação do solo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Pressão de preconsolidação como ferramenta de análise da sustentabilidade estrutural de classes de solos com diferentes usos

O principal problema ambiental causado pelo uso do solo em áreas de preservação permanente longitudinais aos rios é a supressão da mata ciliar. O tipo e a intensidade desse uso alteram a estrutura do solo e comprometem as funções físicas dessas áreas, principalmente próximo aos cursos d'água. O objetivo deste trabalho foi avaliar a sustentabilidade estrutural, a partir do ensaio de compressão uniaxial, de três classes de solo (Cambissolo Háplico, Argissolo Amarelo e Gleissolo Háplico) e o impacto de diferentes tipos de usos do solo - não permitido pela legislação ambiental - de áreas de preservação permanente na sub-bacia do rio Ribeira de Iguape, SP. Foram delimitadas na área experimental três classes de solo: Cambissolo, Argissolo e Gleissolo. Numa primeira etapa, compararam-se as três classes de solos sob mata nativa e sob pastagem. Na segunda, avaliou-se a influência de diferentes tipos de uso do solo - cultivo de banana, pastagem degradada, uso silvipastoril e mata nativa - sobre a estrutura de um Cambissolo. A pressão de preconsolidação mostrou-se ferramenta capaz de identificar a degradação nos solos. O uso do solo nas áreas de preservação permanente altera a pressão de preconsolidação do solo, causando sua degradação estrutural, colocando em risco a sustentabilidade das terras, e não deve ser permitido. O Gleissolo mostrou maiores valores de pressão de preconsolidação em função de teores crescentes de água e, portanto, maior capacidade de suporte de carga em relação ao Cambissolo e Argissolo. O cultivo de banana foi o tipo de uso que mais degradou os solos das áreas de preservação permanente.

Compressibilidade do solo e sistema radicular da cana-de-açúcar em manejo com e sem controle de tráfego

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dilatometer tests in a Leda clay crust

The dilatometer test results have been lately applied in foundation design for prediction of settlement and bearing capacity problems. The equipment, its calibration, test procedures and test data interpretation are simple. These advantages seem to explain the increasing use of the dilatometer (DMT) test as a routine technique for subsoil investigation. The DMT test boreholes were carried out on the grounds of the National Research Council (NRC) in Ottawa. Several test results based on laboratory, and other in situ tests available in the literature for the Leda clay deposit in Ottawa area were used to provide correlations between geotechnical properties and soil index parameters as proposed by Marchetti (1980). More appropriated relationships, even though preliminaries, are presented for the crust layer.

Prediction and spatial variability of soil dynamic properties in sugar cane fields of São Paulo State Brazil

The objective of this work was to model and diagnose the spatial variability of soil load support capacity (SLSC) in sugar cane crop fields, as well as to evaluate the management impact on São Paulo State soil structure. The investigated variables were: pressure preconsolidation (sigma(p)), apparent cohesion () and internal friction angle (). The conclusions from the results were that the models and spatial dependence maps constitute important tools in the prediction and location of the mechanical internal strength of soils cultivated with sugar cane. They will help future soil management decisions so that soil structure sustainability will not be compromised.

Friction and wear properties of functionally graded aluminum matrix composites

Aluminum matrix composites are currently considered as promising materials for tribological applications in the automotive, aircraft and aerospace industries due to their great advantage of a high strength-to-weight ratio. A superior combination of surface and bulk mechanical properties can be attained if these composites are processed as functionally graded materials (FGM's). In this work, homogeneous aluminum based matrix composite, cast by gravity, and aluminum composites with functionally graded properties, obtained by centrifugal cast, are tested against nodular cast iron in a pin-on-disc tribometer. Three different volume fractions of SiC reinforcing particles in each FGM were considered in order to evaluate their friction and wear properties. The sliding experiments were conducted without lubrication, at room temperature, under a normal load of 5 N and constant sliding speed of 0.5 ms-1. The worn surfaces as well as the wear debris were characterized by SEM/EDS and by atomic force microscopy (AFM). The friction coefficient revealed a slightly decrease (from 0.60 to 0.50) when FGM's are involved in the contact instead of the homogeneous composite. Relatively low values of the wear coefficient were obtained for functionally graded aluminum matrix composites (≈10-6 mm3N-1 m-1), which exhibited superior wear resistance than the homogeneous composite and the opposing cast iron surface. Characterization of worn surfaces indicated that the combined effect of reinforcing particles as load bearing elements and the formation of protective adherent iron-rich tribolayers has a decisive role on the friction and wear properties of aluminum matrix composites.