Nickel adsorption by soils in relation to pH, organic matter, and iron oxides

There is little information on nickel adsorption by Brazilian soils. The objective of this experiment was to determine the effect of pH, organic matter, and iron oxides on nickel adsorption by three soils: a clayey Anionic Rhodic Acrudox, a sandy clay loam Anionic Xanthic Acrudox, and a clayey Rhodic Hapludalf. Soil samples were collected from the 0-0.2 in layer and treated to eliminate organic matter and iron oxides. The nickel adsorption was evaluated in the original samples and in those treated to remove organic matter and to remove both, organic matter and iron oxides, using 2 g soil + 20 mL of 0.01 mol L-1 CaCl2 solution containing 5 mg L-1 Ni, pH varying from 3.5 to 7.5. The nickel adsorption decreased with the elimination of organic matter. For the samples without organic matter and iron oxides, adsorption decreased only in the Anionic Rhodic Acrudox. The pH was the main factor involved in nickel adsorption variation, and for soil samples without organic matter and iron oxides, the maximum adsorption occurred at higher pH values.

Biomimetic biosensor based on lipidic layers containing tyrosinase and lutetium bisphthalocyanine for the detection of antioxidants

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Oxygen diffusion in superconducting oxides

Since the discovery of high-temperature superconductivity of cuprate oxides, it has been clear that it is strongly affected by the oxygen content, which is also a crucial factor to determine other physical properties of high T-c superconductors. Non-stoichiometric (interstitial) oxygen strongly influences the physical properties of various superconducting oxides, in particular by creating conducting holes. It is now ascertained that the amount of holes injected depends not only on the content of interstitial oxygen, but also on its ordering. Rearrangement of the oxygen ordering may occur even below room temperature due to the unusual high mobility of these atoms. This way, mechanical spectroscopy is one of the most adequate techniques for the study of the mobility (diffusion) of oxygen atoms. This technique allows the determination of the jump frequency of an atomic species precisely, regardless of the model or the different possible types of jumps. In order to evaluate the mobility and the effect of oxygen content on these oxides, ceramic samples we prepared and submitted to several oxygen removal cycles alternately with mechanical relaxation measurements. As for SBCO, it was assumed that the peak was due to O(1)-O(5) jumps of oxygen atoms at the chain terminals or in chain fragments in the orthorhombic phase. In the case of BSCCO, the results showed complex anelastic relaxation structures, which were attributed to interstitial oxygen atom jumps between two adjacent CuO planes.

ZnO-TiO2 composite formed by mixed oxides via polyol

Among the researches on preparation and test of nanostructured materials, titanium dioxide and zinc oxide have been the most frequent studied oxides. In order to extend their properties, composites have been prepared using three different methods: Polyol Method, Sol-gel Process and a combination of the two processes (hybrid process). Recent research showed best properties in composite materials than in pure oxides. In this work is presented the preparation and the structural characterization of ZnO-TiO2 composite nanostructures to be tested for their performance in electrocatalysis and in further trial on photovoltaic cells.

Alloys and oxides on carbon-supported Pt-Sn electrocatalysts for ethanol oxidation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Platinum-coated nanostructured oxides for active catalytic electrodes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of rare earth oxides doping SnO2.(Co1/4,Mn3/4)O-based varistor system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Magnetic oxides of spinel structure: Study of CoxCuyMnzO4 and MgxNiyMnzO4 manganites (x+y+z=3)

Systematic studies in manganites of spinel structure have been undertaken. We report on the magnetic properties of two particular cases, in which one of the transition metals, Mg2+ is non-magnetic (NiMgxMn2-xO4) or presents a stable oxidation state, Cu2+ (CoxCuyMnzO4, x + y + z = 3). The magnetic behaviour is described with respect to varying contents of cobalt, copper or manganese. A ferrimagnetic transition is observed at 110-120 K, which depends on the cobalt content. Presence of copper increases the coercive field by a factor of ten with respect to the parent compound NiMn2O4. (c) 2006 Elsevier B.V. All rights reserved.

Glasses containing lutetium fluoride

Glasses containing lutetium fluoride have been prepared in the system BaF2 - SrF2 - ZnF2 - LuF3 - InF3. The composition of the phases crystalling out of these glasses suggests octahedral pre-arrangement comprising [LuF6] and [Sr(Ba)F-2 structural fragments.

OXIDES AS HETEROGENEOUS PROMOTERS FOR LIQUID-PHASE HYDROCARBONYLATION REACTIONS WITH IODOCARBONYLRUTHENIUM CATALYSTS

Basic or acid oxides, used as heterogeneous promoters of carbonylruthenium catalysts in liquid-phase hydrocarbonylation reactions on oxygenated substrates, strongly affect the activity and selectivity of the catalytic system. Concurrent or successive reactions of simple carbonylation, homologation, hydrogenation to hydrocarbons, and etherification take place to varying extents. Carbonylation and etherification are favored by acid oxides and homologation and hydrogenation by basic oxides. This behavior is related to the formation and stabilization by the oxides of H+ and H- hydridocarbonylruthenium catalytic species, whose relative concentrations in solution depend on the nature of the oxide. Heterogeneous oxides are easily separated and recycled from the reaction mixture. Their use simplifies the catalytic system and allows one to direct the catalytic process toward the target product.

Influence of the oxygen adsorbed on tin varistors doped with Co, Mn and Cr oxides

The non-ohmic properties of the 98.90% SnO2+(1-x)%CoO+0.05% Cr2O3+0.05% Nb2O5+x% MnO2 varistor system (all of them in mol %), as well as the influence of the oxidizing and reducing atmosphere on this system were studied in this work. Experimental evidence indicates that the electrical properties of the varistor depend on the defects that occur at the grain boundary and on the adsorbed oxygen species such as O''(2), O'(2), O in this region. Thermal treatments at 900 degreesC in oxygen and nitrogen atmospheres indicated such a dependence with the values of the non-linearity coefficient (alpha) increasing under oxygen atmosphere, being reduced in nitrogen atmosphere and restored after a new treatment in oxygen atmosphere, presenting a reversibility in the process. EDS analysis accomplished by SEM showed the distribution of the oxides in the varistor matrix. (C) 2002 Kluwer Academic Publishers.

Influence of the rare-earths oxides doped on the SnO2CoOMnO2Ta2O5 varistor system

The tin dioxide is an n-type semiconductor, which exhibits varistor behavior with high capacity of absorption of energy, whose function is to restrict transitory over-voltages without being destroyed, when it is doped with some oxides. Varistors are used in alternated current fields as well as in continuous current, and it can be applied in great interval of voltages or in great interval of currents. The electric properties of the varistor depend on the defects that happen at the grain boundaries and the adsorption of oxygen. The (98.90-x)%SnO2.0.25%CoO+0.75%MnO2+0.05%Ta2O5+0.05%Tr2O3 systems, in which Tr=La or Nd. Current-voltage measurements were accomplished for determination of the non-linear coefficient were studied. SEM microstructure analysis was made to evaluate the microstructural characteristics of the systems. The results showed that the rare-earth oxides have influenced the electrical behavior presented by the system. (C) 2002 Kluwer Academic Publishers.

An investigation of metal oxides which are photoluminiscent at room temperature

Amorphous thin films, based on different network formers, were processed by a soft chemical process called the polymeric precursor method. The resultant amorphous metal oxides, displayed intense photoluminescence (PL) at room temperature. Heat treatment increases the PL intensity of these materials. Theoretical ab initio calculations are correlated with the observed experimental trends. (C) 2004 Elsevier B.V. All rights reserved.