Kraft pulp from juvenile and mature woods of corymbia citriodora

Kraft pulp produced from juvenile and mature wood from thirty-two-year-old Corymbia citriodora trees was evaluated. The stem was subdivided into regions of juvenile and mature wood, and then it was transformed into chips. These materials were then cooked in the Laboratory of Pulp and Paper at São Paulo State University (UNESP, Botucatu, SP, Brazil) and the physico-mechanical properties of the pulps were determined. The results showed that: (1) the pulp yields of mature wood were up to 4.4% greater in comparison to the juvenile wood, (2) the juvenile wood pulp required a shorter refining time than mature wood to reach the same Schopper-Riegler degree, (3) the juvenile wood pulp presented lower specific volume, and (4) the mature wood pulp presented greater air resistance, tensile, tear and burst index values, stress-strain factor, and stretch than the juvenile wood pulp.

Polpação Kraft e Kraft/AQ da madeira de híbrido de Eucalyptus urograndis destinada à produção de polpa para dissolução

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effect of s/g ratio on kraft pulping and ecf bleaching of some poplars and eucalyptus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

EVALUATION OF EUCALYPTUS KRAFT PULP LIGNIN THROUGH THE NITROBENZENE OXIDATION, COPPER OXIDE REDUCTION AND ACIDOLYSIS TECHNIQUES

This study aimed to evaluate the sensitiveness of the information obtained for the residual lignin from Eucalyptus grandis kraft pulps analyzed through the nitrobenzene oxidation, copper oxide (CuO) reduction and acidolysis techniques. The chips were cooked, resulting pulps of kappa number 14,5 and 16,9, respectively. Both lignins' pulps were evaluated through three methods (nitrobenzene oxidation, copper oxide oxidation and acidolysis). Then, they were subjected to an oxygen delignification stage. The 16,9 kappa number pulp resulted in higher levels of non-condensed lignin structures by the acidolysis method, higher syringyl/vanillin ratios (S/V) by the nitrobenzene and copper oxide methods and better performance in the oxygen delignification stage. The different methods allowed to differ the residual lignin pulps with kappa number 14,5 and 16,9, and the nitrobenzene oxidation method showed the highest sensitiveness in this study results.

Efeito dos ácidos hexenurônicos e da lignina no desempenho da ozonólize, em diferentes pHs da reação

The effect of pH on the performance of the ozonolysis stage in pulp production was evaluated for conventional and acid treated brown and oxygen delignified eucalyptus kraft pulps. The objective was to determine separately the effects of lignin and hexenuronic acid on the performance of the ozonolysis stage. The reaction of ozone with hexenuronic acid is less sensitive to pH than the reaction of ozone with lignin. The efficiency and the selectivity of the reaction of ozone with pulp decreases after removal of hexenuronic acids. Increasing up to 7.0 the pH during the ozonolysis is viable in the sequence Z/D(EOP)D, resulting in savings of H2SO4 (8,5 kg/tsa) and NaOH (5 kg/tsa), but is not recommended in the sequence Z/ED(PO).

Xylanase and β-Xylosidase from Penicillium janczewskii: Production, Physico-Chemical properties, and application of the crude extract to pulp biobleaching

Extracellular xylanase and β-xylosidase production by a Penicillium janczewskii strain were investigated in liquid cultures with xylan from oat spelts under different physical and chemical conditions. The selected conditions for optimized production of xylanase and β-xylosidase were 7 days, pH 6.5, at 30 °C and 8 days, pH 5.0, at 25 °C, respectively. The xylanase exhibited optimal activity in pH 5.0 at 50 °C and the β- xylosidase in pH 4.0 at 75 °C. The xylanase was more stable at pH 6.0 to 9.5, while the β-xylosidase remained stable at pH ranging from 1.6 to 5.5. The xylanase half-life (T50) at 40, 50, and 60 °C was 183, 15, and 3 min, respectively. β-xylosidase half-life was 144, 8, and 4 min at 50, 65, and 75 °C, respectively. When applied to the biobleaching of Eucalyptus kraft pulp, xylanase dosages of 2 and 4 U/g dried pulp reduced, respectively, kappa number by 3.0 and 3.3 units after 1 h treatment, demonstrating that the use of P. janczewskii xylanases in this process is quite promising. The pulp viscosity was not altered, confirming the absence of cellulolytic enzymes in the fungal extract.

A influência dos ácidos hexenurônicos no rendimento e na branqueabilidade da polpa kraft

This study investigated the impact of pulp hexenuronic acids (HexAs) content on pulping yield by changing cooking reaction temperature. The bleachability of pulps containing variable amounts of HexAs was also investigated. The cooking at 170 degrees C produced pulp of kappa number, HexAs and screen yield of 16.2, 49.4 mmol/kg and 50.2%, respectively, whereas the cooking at 156 degrees C resulted pulp of kappa 17.0, 61.3 mmol/kg HexAs and 50.8% screened yield. The pulp produced at lower cooking temperature also showed better bleachability as evaluated by the total amount of active chlorine required to achieve 90% ISO. The sequence OAHTD(EP) DD showed the lowest bleaching performance among all.

Geração de finos no branqueamento de pasta kraft de eucalipto e seu efeito nas propriedades do papel

Este trabalho teve por objetivo avaliar a quantidade de finos gerada por diferentes reagentes de branqueamento e seu efeito nas propriedades físicas e mecânicas da celulose kraft de eucalipto. A polpa foi branqueada por quatro sequências diferentes. Parte das amostras foi classificada em equipamento Bauer-McNett, sendo a parte não classificada (global) refinada para 40 ºSR, em moinho laboratorial PFI. As duas maiores porções de cada amostra proveniente da classificação foram também refinadas com o mesmo número de revoluções que a sua amostra global. Realizaram-se ensaios físicos e mecânicos das amostras refinadas, e suas fibras foram analisadas em equipamento FQA (Fiber Quality Analyser), antes e depois do refino. A maior quantidade de finos foi observada nas polpas refinadas e na sequência-referência. Os resultados de tração foram mais elevados e significativos nas amostras globais; as polpas classificadas não apresentaram diferença entre si, sendo atribuída a maior resistência à tração na presença de finos. A resistência ao rasgo foi afetada pelo comprimento das fibras e não pelo teor de finos. Os maiores valores de ascensão capilar Klemm ocorreram nas amostras classificadas em razão da ausência de finos e do maior comprimento de fibras.

Efeito de reagentes de branqueamento nas propriedaes físicas e mecânicas da polpa de celulose Kraft de eucalipto

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Lignin chemistry and topochemistry during kraft delignification of Eucalyptus globulus genotypes with contrasting pulpwood characteristics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudos da polpação kraft, branqueamento e refino de eucalyptus grandis x eucalyptus urophylla

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Attractiveness of Different Citrus Pulps to the Leaf-Cutting Ant Atta sexdens rubropilosa (Hymenoptera: Formicidae)

The most common control method Uses toxic baits consisted of dehydrated citrus pulp as carrier and attractant. However, the portion of the citrus fruit that is attractive to ants is still Unknown, despite its importance in chemical control. This study compared the attractiveness of different fruit parts of citrus pulps to Atta sexdens rubropilosa workers. Three treatments: pellets of industrial citrus pulp, albedo (mesocarp), and whole citrus pulp were offered randomly to ants and the removal of these substrates by workers was observed. Tie three pulps Were equally attractive to this species (F = 0.8033; p = 0.4633). Although the whole pulp included the epicarp, it was as attractive as the other treatments, possibly because, the material was heated during processing, eliminating any volatile substance that could repel ants.

Influência da densidade básica da madeira de clones de Eucalyptus grandis x Eucalyptus urophylla na qualidade da polpa branqueada.

The study analyzed the wood basic density effect in two Eucalyptus grandis x Eucalyptus urophylla hybrid clones (440 kg/m(3) e 508 kg/m(3)) on bleached pulp quality (fiber dimensions and physical-mechanical properties). The woods performance on pulping, bleaching and beating results were analyzed. The Kraft pulping was carried out in forced circulation digester in order to obtain 17 +/- 1 kappa number targets. The pulps were bleached to 90 +/- 1 using delignification oxygen and D0EOPD1 bleaching sequence. Bleached pulp of low basic density clone showed, significantly, lowest revolutions number in the PFI mill to reach tensile index of 70 N.m/g, low Schopper Riegler degree and generated sheets with higher values to bulk and opacity. These characteristics and properties allow concluding that bleached pulp of low basic density clone was the most indicated to produce printing and writing sheets. The bleached pulp of high basic density clone showed higher values of bulk and capillarity Klemm and lower water retention value when analyzed without beating. The bleached pulp of high basic density clone showed more favorable characteristics to the production of tissue papers.

Response of human pulps after professionally applied vital tooth bleaching

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Response of human pulps following acid conditioning and application of a bonding agent in deep cavities

Objectives. The aim of this in vivo study was to evaluate the human dental pulp response when a one-bottle adhesive system was applied on etched or unetched deep dentine.Methods. Eighteen class V deep cavity preparations were divided in three groups: group 1-total etching + two coats of single bond (SB) + composite resin (Z-100); group 2-enamel etching + two coats of SB + Z-100, group 3-cavity floor lined with a calcium hydroxide liner (Dycal) + acid-etching of enamel and lateral walls + two coats of SB + Z-100. Two teeth were used as intact control group. After 30 days the teeth were extracted and processed through H and E, Masson's trichrome and Brown and Brenn staining techniques.Results. Moderate inflammatory response, disorganization of pulp tissue, as well as, deposition of thin layer of reactionary dentin were observed in group 1 teeth in which the remaining dentin thickness (RDT) was less than 300 mum. These histological findings appear to be related to long resin tags formation and bonding agent diffusion through dentinal tubules. In group 2, slight inflammatory response was observed only in one tooth in which the RDT was 162 mum. In group 3, all the teeth showed normal histological characteristics which were similar to the intact control group. Presence of bacteria was not correlated with the intensity of pulpal response. The patients reported no symptoms during the experiment. Radiographic evaluation showed no periapical pathology for any of the teeth,Significance and conclusions. Acid-etched deep dentin (RDT less than 300 mum) lined with SB causes more intense pulpal response than unetched deep dentin. Based on the results observed in the present study and the conditions in which it was carried out, we recommend the application of a biocompatible liner before etching deep dentin and applying SB. (C) 2002 Academy of Dental Materials. Published by Elsevier B.V. Ltd. All rights reserved.