Study of ceramic block manufacture with the addition of waste from iron ore extraction

This work is intended to study the possibility of adding an amount of waste from iron mining in the ceramic mass. Clay and coal, from Vale do Paraiba, Sao Paulo, Brazil, were used in this research. These raw materials are used in the ceramic block manufacture. Clay and waste were analyzed by X-ray fluorescence and X-ray diffraction, particle size, differential thermal and thermogravimetric analysis. Liquid limit and plasticity index tests were performed in order to determine the amount of waste that which should be used in the ceramic mass. After determining the amount of waste, all samples were uniaxially pressed and sintered at 900 degrees C. Surface roughness measurements, apparent porosity and bulk density technique and three-point flexural tests were also performed to characterize the samples. The results showed that by adding the exact amount of waste, which was determined by the essays, it is possible to manufacture solid bricks.

Operational and environmental assessment on the use of charcoal in iron ore sinter production

A study was carried out into the use of charcoal as a supplementary fuel in the iron-ore sintering process. The primary fuel was coke breeze and anthracite with 0, 10, 25, 50 and 100% replacement of the energy input with charcoal to produce sinter. This was achieved by considering the carbon content of each fuel and its corresponding participation on fuel blending, in order to have the same carbon input in each test run. An extensive analysis of the environmental impact was carried out regarding the atmospheric pollutants characterization (dust, sulphur dioxide, nitrogen oxides, carbon monoxide, carbon dioxide, methane, total hydrocarbons, and dioxins and furans). Experimental results indicate that fuel blending where 50% of the heat input was provided by charcoal may be comparable with those using 100% coke, under normal sintering conditions, and may result in a 50% reduction on greenhouse gas emission. It was also observed that while dust, methane and hydrocarbons emissions increased, the total dioxins and furans, expressed as polychlorinated dibenzodioxins/furans, decreased approximately 50% when compared with operation with 100% coke.

Corrosion behavior in graphite refractories impregnated with ZrO 2 and CeO 2 carrying solutions

This paper investigates corrosion behavior in graphite refractory hot metal impregnated with ZrO 2 and CeO 2 carrying solutions used in Blast Furnace hearth, consisting of 50% graphite and 50% anthracite. Corrosions tests were carried out by means of finger test method in an induction furnace, using bar-shaped 30×30×280 mm test specimens and hot metal from CSN#2 Blast Furnace runner. The temperature chosen for this test was 1520°C and sixty-minute isotherm. Upon test completion, test specimens were characterized by their dimensional variation, X-ray diffractometry and Scanning Electronic Microscopy (SEM).

Mapeamento de Paleosuperfícies associadas a identificação de depósitos supérgenos de cobre como ferramenta de exploração mineral na região de Itapeva e Ribeirão Branco- Vale do Ribeira, estado de São Paulo, Brasil

A few examples of supergene ore formation and their interaction with morphogenesis (palaeosurfaces) and weathering mineralogy are discussed. Geomorphological and mineralogical records to characterize palaeosurfaces associate the weathering of primary minerals and their relationship with concentrations of cooper and iron ore deposits in southeastern state of São Paulo, Brazil. We have distinguished two palaeosurfaces generated by several weathering phases and controlled by the geological framework. The first and oldest upper palaeosurfaces (900 - 1000 m a.s.l.), situated in Riberão Branco (Alto do Brancal), were developed on silico-limestones. It is formed by typical iron laterites enriched by secondary products of cooper. The second and younger level palaeosurfaces located in Itapeva (Santa Blandina and Bairro do Sambra). This palaeosurface is formed by copper percolating through the weathered rock (saprolite). Other features can be observed like neo-formed products in laterites. They are classified into two types: clay like silico- cupriferous products (with noticeable amounts of iron) and copper minerals (crysocolla, in their flat slopes). These features allowed the presence of copper ores and their morphogenesis control will help in the exploration and prospecting of supergene ore mineral.

Evolução termocronológica do sudoeste de Angola e correlação com o sudoeste brasileiro: termocronologia por traços de fissão em apatita

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise do emprego de materiais alternativos no alto forno da Arcelormital Tubarão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Texturas e propriedades reológicas dos minérios de ferro do quadrilátero ferrífero (MG) e sua utilização em beneficiamento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Geologia do platô N6 - província mineral de Carajás (SP)

The N6 Plateau presents an iron-ore occurence in Carajás Mineral Province, standing near to actually operating deposits. Geological mapping in 1:10,000 scale and integration of geochemical, geophysical, petrography and drilling turns possible interpretation of his geological evolution. The mapped area has lithotypes from Archean Grão Pará Group, comprising very lowgrade metamorphic basic rocks and iron formation and an Proterozoic sedimentary association of conglomeratic sandstones called as Caninana Unity. The structural geology in given by a regional scale homoclinal, where the Grão Pará Group strata dips towards SW, as a part of the Northern Limb of the Carajás Fold. Subsequent deformation associated to the installation of the Carajás Shear Zone presents as E-W fold axis. Geochemical evidence permits to consider de Parauapebas Formation as the rocks which has been hydrothermally-altered to outsourcing fluids responsible to deposition of iron formations in the oceanic system, including different signatures which can be interpreted as possible sub-embayments in the Carajás Basin. The iron ore in the area occurs in subsurface as very fine friable hematite generated by supergenous enrichment of the iron formation. The conceived geologic model differs from the current academic proposal on the fact that hydrothermal alteration has been involved on the jaspelite enrichment. Metamorphism on the Parauapebas Formation presents paragenesis considered as ocean-floor metamorphism which precedes de deformation insofar as the rocks show no tectonic fabric referring to shallow crust evolution. Geophysical methods such as magnetometry and gravimetry presents excellent results for structural interpretation in uneven exposed terrain

Caracterização geofísica e geológica das formações ferríferas do Grupo Macaúbas - MG

Pós-graduação em Geologia Regional - IGCE

Dissolução redutiva de minério de ferro por Acidithiobacillus ferrooxidans para a recuperação de metais de interesse econômico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Gold-bearing iron duricrust in Central Brazil

In the Cuiabá region-State of Mato Grosso, Central Brazil-primary gold mineralization is hosted by two generations of quartz veins in Precambrian metamorphic terrains of the Cuiabá Group. Gold is mined from the veins and mainly from the eluvial horizons that cover the deeply altered basement. In the lodes gold occurs as small particles (less than 1 mm) associated with pyrite and contains up to 5% Ag. Larger particles and nuggets of almost pure gold are found in the iron duricrust which caps the upper levels of the weathering profile. It is difficult to determine the average grade of this kind of deposit but some prospects in the Cuiabá region produce up to 2 g gold per ton of ore. Lateritization is responsible for both the formation of the iron crust and the concentration of gold within the regolith. Under a tropical climate, the supergene alteration of phyllites of the Cuiabá Group has led to the formation of a weathering profile consisting typically of saprolite, mottled clay zone and duricrust, from bottom to top. The duricrust is directly derived form the in situ weathering of phyllites. Geochemical balance calculations indicate that in the transition from the saprolite to the duricrust lateritization has promoted a progressive loss of Si, Al and K, and more than 500% of absolute Fe enrichment. Gold underwent a supergene evolution related to the development of the weathering profile. In the saprolite and mottled clay zone, associated with quartz and oxidized sulfides, gold dissolves as demonstrated by corrosion features at the surface of the particles. The formation of secondary gold in the duricrust is indicated by the larger size of the nuggets, their higher fineness and the close relationship between gold and the neoformed iron oxy-hydroxides. © 1991.

Magnetic properties of spindle-type iron fine particles obtained from hematite

Spindle-type iron fine particles have been prepared by reduction of silica-coated-hematite particles. Hydrogen reduction of the coated-hematite cores yielded uniform spindle-type iron particles, which were stabilized by surface oxidation. Narrow particle distributions are observed from TEM measurements. X-ray, Mössbauer and magnetization data are in agreement with the presence of nanosized α-Fe particles, having surface layer of spinel structure oxide. Mössbauer spectra show that the oxide surface is superparamagnetic at room temperature. © 2001 Elsevier Science B.V. All rights reserved.