Model to design drip hose lateral line using two spacing between emitters

The use of non-pressure compensating drip hose in horticultural and annual cycle fruits is growing in Brazil. In this case, the challenge for designers is getting longer lateral lines with high values of uniformity. The objective of this study was to develop a model to design longer lateral lines using non-pressure compensating drip hose. Using the developed model, the hypotheses to be evaluated were: a) the use of two different spacing between emitters in the same lateral line allows longer length; b) it is possible to get longer lateral lines using high values of pressure variation in the lateral lines since the distribution uniformity stays below allowable limits. A computer program was developed in Delphi based on the model developed and it is able to design lateral lines in level using non-pressure compensating drip hose. The input data are: desired distribution uniformity (DU); initial and final pressure in the lateral line; coefficients of relationship between emitter discharge and pressure head; hose internal diameter; pipe cross-sectional area with the dripper; and roughness coefficient for the Hazen-Williams equation. The program allows calculate the lateral line length with three possibilities: selecting two spacing between emitters and defining the exchange point; using two pre-established spacing between emitters and calculating the length of each section with different spacing; using one emitter spacing. Results showed that the use of two sections with different spacing between drippers in the lateral line didn't allow longer length but got better uniformity when compared with lateral line with one spacing between emitters. The adoption of two spacing increased the flow rate per meter in the final section which represented approximately 80% of the lateral line total length and this justifies their use. The software allowed DU above 90% with pressure head variation of 40% and the use of two spacing between emitters. The developed model/software showed to be accurate, easy to handle and useful for lateral line design using non-pressure compensating drip hose.

Incidência da varíola, causada por Asperisporium caricae, em folhas de mamoeiros submetidos ao manejo orgânico, em diferentes ambientes de cultivo

Mudas de mamoeiro da cultivar Baixinho de Santa Amália foram transplantadas para covas de 40x60x40 cm, em áreas de três estruturas contíguas: (a) estufa sombreada (cobertura de plástico), (b) estufa sombreada + sombrite (cobertura adicional de sombrite com 30% de sombreamento sobre o plástico) e (c) telado (cobertura exclusiva de sombrite 30%). Ao lado de tais estruturas foi implantada uma área de cultivo de mamoeiro em ambiente natural. Os tratos culturais aplicados foram os condizentes às normas técnicas vigentes na agricultura orgânica. As irrigações foram procedidas com mangueira plástica, evitando-se molhar folhas e frutos. Aos 45 dias pós-transplantio e, subseqüentemente, a intervalos mensais, as plantas foram inspecionadas em relação à incidência de lesões foliares causada pelo fungo Asperisporium caricae. Para efeito de análise estatística, após o teste de homogeneidade das variâncias, foram consideradas quatro repetições por ambiente (tratamento), com seis plantas úteis por parcela. O modelo de quantificação da doença indicou efeito altamente significativo dos ambientes protegidos, estufa e estufa sombreada, quanto à incidência de sintomas, em comparação com ambientes de telado e em área natural de cultivo. Durante os 12 meses de avaliações foi constatada alta correlação entre incidência da doença e pluviosidade e umidade relativa do ar. As estruturas cobertas com plástico demonstraram alto potencial de controle de A. caricae, sendo, portanto, recomendáveis no sistema orgânico de produção do mamoeiro.

Periodic inspection of sprayers: diagnostic to the northern of Paraná

Para a otimização no uso de agroquímicos, vários países têm realizado inspeções periódicas em pulverizadores agrícolas. No Brasil, o conhecimento do estado destas máquinas pode nortear pesquisas e investimentos em orientação de uso e de manutenção das mesmas. O objetivo deste trabalho foi verificar o estado de manutenção de pulverizadores em uso para a região norte do Estado do Paraná. Foram avaliados itens como: presença, estado e escala do manômetro, estado das mangueiras, estado dos antigotejadores, presença de vazamentos, estado da barra, estado dos filtros, estado das pontas de pulverização e erros na taxa de aplicação. As máquinas foram caracterizadas como aprovadas quando não havia falha em nenhum item avaliado. O fator que ocasionou o maior índice de reprova entre as máquinas foi a escala incorreta do manômetro, que reprovou 84,55% das máquinas avaliadas. Outro fator de destaque foi a taxa de aplicação incorreta em 75,5% das máquinas. do total dos 110 pulverizadores avaliados,apenas uma unidade foi aprovada.

The importance of knowing the home conditions of patients receiving long-term oxygen therapy

Purpose: Long-term oxygen therapy (LTOT) is one of the main treatments for patients with chronic obstructive pulmonary disease. Patients receiving LTOT may have less than optimal home conditions and this may interfere with treatment. The objective of this study was, through home visits, to identify the characteristics of patients receiving LTOT and to develop knowledge regarding the home environments of these patients.Methods: Ninety-seven patients with a mean age of 69 plus or minus 10.5 years were evaluated. This study was a cross-sectional descriptive analysis. Data were collected during an initial home visit, using a questionnaire standardized for the study. The results were analyzed retrospectively.Results: Seventy-five percent of the patients had chronic obstructive pulmonary disease, and 11% were active smokers. The patients' mean pulse oximetry values were 85.9% plus or minus 4.7% on room air and 92% plus or minus 3.9% on the prescribed flow of oxygen. Most of the patients did not use the treatment as prescribed and most used a humidifier. The extension hose had a mean length of 5 plus or minus 3.9 m (range, 1.5-16 m). In the year prior to the visit, 26% of the patients received emergency medical care because of respiratory problems. Few patients reported engaging in leisure activities.Conclusion: The home visit allowed us to identify problems and interventions that could improve the way LTOT is used. The most common interventions related to smoking cessation, concentrator maintenance and cleaning, use of a humidifier, and adjustments of the length of the connector hose. Therefore, the home visit is a very important tool in providing comprehensive care to patients receiving LTOT, especially those who show lack of adequate progress and those who show uncertainty about the treatment method.

Avaliação da uniformidade de aplicação de água em gotejadores em função do teor de ferro

Este trabalho teve por objetivo estudar a variação de vazão em tubogotejadores NaanPC laranja e NaanPC azul em função de precipitados químicos, ao longo do tempo de funcionamento, quando submetidos a uma água rica em ferro, avaliando-se especificamente o coeficiente de uniformidade de Christiansen (CUC) e o coeficiente de uniformidade de distribuição (CUD). O experimento foi desenvolvido em uma bancada de ensaios para tubogotejadores no Laboratório de Ensaio de Equipamentos para Irrigação do Departamento de Engenharia Rural da Faculdade de Ciências Agronômicas - UNESP, localizado no município de Botucatu – SP. O experimento foi montado em esquema fatorial 2x2x7, sendo duas doses de Fe, dois modelos de gotejadores e sete tempos de funcionamento, com três repetições, totalizando 84 parcelas experimentais. Efetuou-se a análise de variância pelo teste F. As médias das vazões dos gotejadores foram comparadas pelo teste de T de Student a 5% de probabilidade. Os resultados obtidos não apontaram diferença significativa nas diferentes doses de ferro. Entretanto, os resultados apontaram diferença significativa na interação gotejador x tempo e coeficiente de uniformidade de Christiansen (CUC).

Perda de carga em mangueiras gotejadoras novas e usadas

This paper aims to determine the importance of emitter ́s local head loss in the hydraulic design of hose drip lines, as well as comparing the result of equations that calculate the local head loss; besides verifying the influence of iron precipitated at the hose head loss made in Brazil. The result found that localized head loss represents 23% of the total head loss; the equations showed significant results and the total head loss increased in an average of 20% after the irrigation system was used with water rich in iron.

Model to increase the lateral line length of drip irrigation systems

Non-pressure compensating drip hose is widely used for irrigation of vegetables and orchards. One limitation is that the lateral line length must be short to maintain uniformity due to head loss and slope. Any procedure to increase the length is appropriate because it represents low initial cost of the irrigation system. The hypothesis of this research is that it is possible to increase the lateral line length combining two points: using a larger spacing between emitters at the beginning of the lateral line and a smaller one after a certain distance; and allowing a higher pressure variation along the lateral line under an acceptable value of distribution uniformity. To evaluate this hypothesis, a nonlinear programming model (NLP) was developed. The input data are: diameter, roughness coefficient, pressure variation, emitter operational pressure, relationship between emitter discharge and pressure. The output data are: line length, discharge and length of the each section with different spacing between drippers, total discharge in the lateral line, multiple outlet adjustment coefficient, head losses, localized head loss, pressure variation, number of emitters, spacing between emitters, discharge in each emitter, and discharge per linear meter. The mathematical model developed was compared with the lateral line length obtained with the algebraic solution generated by the Darcy-Weisbach equation. The NLP model showed the best results since it generated the greater gain in the lateral line length, maintaining the uniformity and the flow variation under acceptable standards. It had also the lower flow variation, so its adoption is feasible and recommended.

Avaliação hidráulica e de resistência a tração de dois modelos de mangueiras gotejadoras

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Prevalência de brucelose bovina entre rebanhos fornecedores de leite de um laticínio no município de Itirapuã, Estado de São Paulo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da uniformidade de emissão de água utilizando diferentes espaçamentos entre gotejadores na linha lateral

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Caracterização morfocultural e molecular de isolados de Colletotrichum spp. provenientes de diferentes frutas tropicais

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Increasing the lateral line length of drip irrigation systems

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Um Modelo de otimização inteira mista na programação de produção de mangueiras hidráulicas

This work deals with a problem of mixed integer optimization model applied to production planning of a real world factory that aims for hydraulic hose production. To optimize production planning, a mathematic model of MILP Mixed Integer Linear Programming, so that, along with the Analytic Hierarchy process method, would be possible to create a hierarchical structure of the most import criteria for production planning, thus finding through a solving software the optimum hose attribution to its respective machine. The hybrid modeling of Analytic Hierarchy Process along with Linear Programming is the focus of this work. The results show that using this method we could unite factory reality and quantitative analysis and had success on improving performance of production planning efficiency regarding product delivery and optimization of the production flow