Design of a labVIEW system applied to predictive maintenance

The implementation of vibration analysis techniques based on virtual instrumentation has spread increasingly in the academic and industrial branch, since the use of any software for this type of analysis brings good results at low cost. Among the existing software for programming and creation of virtual instruments, the LabVIEW was chosen for this project. This software has good interface with the method of graphical programming. In this project, it was developed a system of rotating machine condition monitoring. This monitoring system is applied in a test stand, simulating large scale applications, such as in hydroelectric, nuclear and oil exploration companies. It was initially used a test stand, where an instrumentation for data acquisition was inserted, composed of accelerometers and inductive proximity sensors. The data collection system was structured on the basis of an NI 6008 A/D converter of National Instruments. An electronic circuit command was developed through the A/D converter for a remote firing of the test stand. The equipment monitoring is performed through the data collected from the sensors. The vibration signals collected by accelerometers are processed in the time domain and frequency. Also, proximity probes were used for the axis orbit evaluation and an inductive sensor for the rotation and trigger measurement. © (2013) Trans Tech Publications, Switzerland.

Towards an intelligent graphical interface for linear programming modelling

The increase of computing power of the microcomputers has stimulated the building of direct manipulation interfaces that allow graphical representation of Linear Programming (LP) models. This work discusses the components of such a graphical interface as the basis for a system to assist users in the process of formulating LP problems. In essence, this work proposes a methodology which considers the modelling task as divided into three stages which are specification of the Data Model, the Conceptual Model and the LP Model. The necessity for using Artificial Intelligence techniques in the problem conceptualisation and to help the model formulation task is illustrated.

A graphical tool for the tomographic characterisation of microstructural features on metal matrix composites

Research on the micro-structural characterization of metal-matrix composites uses X-ray computed tomography to collect information about the interior features of the samples, in order to elucidate their exhibited properties. The tomographic raw data needs several steps of computational processing in order to eliminate noise and interference. Our experience with a program (Tritom) that handles these questions has shown that in some cases the processing steps take a very long time and that it is not easy for a Materials Science specialist to interact with Tritom in order to define the most adequate parameter values and the proper sequence of the available processing steps. For easing the use of Tritom, a system was built which addresses the aspects described before and that is based on the OpenDX visualization system. OpenDX visualization facilities constitute a great benefit to Tritom. The visual programming environment of OpenDX allows an easy definition of a sequence of processing steps thus fulfilling the requirement of an easy use by non-specialists on Computer Science. Also the possibility of incorporating external modules in a visual OpenDX program allows the researchers to tackle the aspect of reducing the long execution time of some processing steps. The longer processing steps of Tritom have been parallelized in two different types of hardware architectures (message-passing and shared-memory); the corresponding parallel programs can be easily incorporated in a sequence of processing steps defined in an OpenDX program. The benefits of our system are illustrated through an example where the tool is applied in the study of the sensitivity to crushing – and the implications thereof – of the reinforcements used in a functionally graded syntactic metallic foam.

Three-Dimensional Semiautomatic Road Extraction From a High-Resolution Aerial Image by Dynamic-Programming Optimization in the Object Space

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

GRAPHICAL REPRESENTATIONS of MESSAGE EXCHANGES INTO WEB SERVICE-BASED APPLICATIONS

Web service-based application is an architectural style, where a collection of Web services communicate to each other to execute processes. With the popularity increase of Web service-based applications and since messages exchanged inside of this applications can be complex, we need tools to simplify the understanding of interrelationship among Web services. This work present a description of a graphical representation of Web service-based applications and the mechanisms inserted among Web service requesters and providers to catch information to represent an application. The major contribution of this paper is to discus and use HTTP and SOAP information to show a graphical representation similar to a UML sequence diagram of Web service-based applications.

Binary integer programming formulations for scheduling in market-driven foundries

This paper describes the development and solution of binary integer formulations for production scheduling problems in market-driven foundries. This industrial sector is comprised of small and mid-sized companies with little or no automation, working with diversified production, involving several different metal alloy specifications in small tailor-made product lots. The characteristics and constraints involved in a typical production environment at these industries challenge the formulation of mathematical programming models that can be computationally solved when considering real applications. However, despite the interest on the part of these industries in counting on effective methods for production scheduling, there are few studies available on the subject. The computational tests prove the robustness and feasibility of proposed models in situations analogous to those found in production scheduling at the analyzed industrial sector. (C) 2010 Elsevier Ltd. All rights reserved.

Allocation of protective devices in distribution circuits using nonlinear programming models and genetic algorithms

The optimized allocation of protective devices in strategic points of the circuit improves the quality of the energy supply and the system reliability index. This paper presents a nonlinear integer programming (NLIP) model with binary variables, to deal with the problem of protective device allocation in the main feeder and all branches of an overhead distribution circuit, to improve the reliability index and to provide customers with service of high quality and reliability. The constraints considered in the problem take into account technical and economical limitations, such as coordination problems of serial protective devices, available equipment, the importance of the feeder and the circuit topology. The use of genetic algorithms (GAs) is proposed to solve this problem, using a binary representation that does (1) or does not (0) show allocation of protective devices (reclosers, sectionalizers and fuses) in predefined points of the circuit. Results are presented for a real circuit (134 busses), with the possibility of protective device allocation in 29 points. Also the ability of the algorithm in finding good solutions while improving significantly the indicators of reliability is shown. (C) 2003 Elsevier B.V. All rights reserved.

Interior point algorithm for linear programming used in transmission network synthesis

This article presents a well-known interior point method (IPM) used to solve problems of linear programming that appear as sub-problems in the solution of the long-term transmission network expansion planning problem. The linear programming problem appears when the transportation model is used, and when there is the intention to solve the planning problem using a constructive heuristic algorithm (CHA), ora branch-and-bound algorithm. This paper shows the application of the IPM in a CHA. A good performance of the IPM was obtained, and then it can be used as tool inside algorithm, used to solve the planning problem. Illustrative tests are shown, using electrical systems known in the specialized literature. (C) 2005 Elsevier B.V. All rights reserved.

Determination of the optimal quantity of crop residues for energy in sugarcane crop management using linear programming in variety selection and planting strategy

The aim of this work was to present organizational models for optimizing the reduction of crop residue generated by the sugarcane culture. The first model consisted of the selection of varieties of sugarcane to be planted meeting the mill requirements and, at the same time, to minimize the quantity of residue produced. The second model discussed the use of residue to produce energy. This is related to the selection of variety and quantity to be planted, in order to meet the requirements of the mill, to reduce the quantity of residue, and to maximize as much as possible the energy production. The use of linear programming was proposed. The two models presented similar results in this study, and both may be used to define the varieties and areas to be cultivated. (C) 2001 Published by Elsevier B.V. Ltd.

Multiobjective 0-1 integer programming for the use of sugarcane residual biomass in energy cogeneration

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Heterogeneity correction in the construction of optimized planning in radiotherapy using linear programming

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Optimization Strategies Based on Sequential Quadratic Programming Applied for a Fermentation Process for Butanol Production

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A simple graphical model of small mammal succession after fire in the Brazilian cerrado

We studied the succession of small mammal species after fire in the cerrado (Neotropical savanna) of Central Brazil. Populations of small mammals were sampled with live-trapping techniques in a series of nine sites of different successional age, ranging from 1 to 26 years after fire. Ten species of small mammals were captured through all the seral stages of succession. Species richness ranged from two to seven species by seral stage. The species were arranged in different groups with respect to abundance along the succession: the first was composed of early successional species that peaked <2 years after fire (Calomys callosus, C. tener, Thalpomys cerradensis, Mus musculus, Thylamys velutinus); the second occurred or peaked 2-3 years after fire (Necromys lasiurus, Gracilinanus sp., Oryzomys scoth). Gracilinanus agilis peaked in the last seral stage. Species richness of small mammals showed an abrupt decrease from an average of four species immediately after fire to two species 5-26 years after the last fire. We propose a simple graphical model to explain the pattern of species richness of small mammals after fire in the cerrado. This model assumes that the occurrence of species of small mammals is determined by habitat selection behavior by each species along a habitat gradient. The habitat gradient is defined as the ratio of cover of herbaceous to woody vegetation. The replacement of species results from a trade-off in habitat requirements for the two habitat variables.

CP and T trajectory diagrams for a unified graphical representation of neutrino oscillations

Recently the CP trajectory diagram was introduced to demonstrate the difference between the intrinsic CP violating effects to those induced by matter for neutrino oscillation. In this Letter we introduce the T trajectory diagram. In these diagrams the probability for a given oscillation process is plotted versus the probability for the CP- or the T-conjugate processes, which forms an ellipse as the CP- or T-violating phase is varied. Since the CP- and the T-conjugate processes are related by CPT symmetry, even in the presence of matter, these two trajectory diagrams are closely related with each other and form a unified description of neutrino oscillations in matter. (C) 2002 Published by Elsevier B.V. B.V.

Design and management optimization of trickle irrigation systems using non-linear programming

A non-linear model is presented which optimizes the lay-out, as well as the design and management of trickle irrigation systems, to achieve maximum net benefit. The model consists of an objective function that maximizes profit at the farm level, subject to appropriate geometric and hydraulic constraints. It can be applied to rectangular shaped fields, with uniform or zero slope. The software used is the Gams-Minos package. The basic inputs are the crop-water-production function, the cost function and cost of system components, and design variables. The main outputs are the annual net benefit and pipe diameters and lengths. To illustrate the capability of the model, a sensitivity analysis of the annual net benefit for a citrus field is evaluated with respect to irrigated area, ground slope, micro-sprinkler discharge and shape of the field. The sensitivity analysis suggests that the greatest benefit is obtained with the smallest microsprinkler discharge, the greatest area, a square field and zero ground slope. The costs of the investment and energy are the components of the objective function that had the greatest effect in the 120 situations evaluated. (C) 1996 Academic Press Limited