Electrical characterization of poly(amide-imide) for application in organic field effect devices

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Bacterial cellulose membrane as flexible substrate for organic light emitting devices

Bacterial cellulose (BC) membranes produced by gram-negative, acetic acid bacteria (Gluconacetobacter xylinus), were used as flexible substrates for the fabrication of Organic Light Emitting Diodes (OLED). In order to achieve the necessary conductive properties indium tin oxide (ITO) thin films were deposited onto the membrane at room temperature using radio frequency (r.f) magnetron sputtering with an r.f. power of 30 W, at pressure of 8 mPa in Ar atmosphere without any subsequent thermal treatment. Visible light transmittance of about 40% was observed. Resistivity, mobility and carrier concentration of deposited ITO films were 4.90 x 10(-4) Ohm cm, 8.08 cm(2)/V-s and -1.5 x 10(21) cm(-3), respectively, comparable with commercial ITO substrates. In order to demonstrate the feasibility of devices based on BC membranes three OLEDs with different substrates were produced: a reference one with commercial ITO on glass, a second one with a SiO(2) thin film interlayer between the BC membrane and the ITO layer and a third one just with ITO deposited directly on the BC membrane. The observed OLED luminance ratio was: 1; 0.5; 0.25 respectively, with 2400 cd/m(2) as the value for the reference OLED. These preliminary results show clearly that the functionalized biopolymer, biodegradable, biocompatible bacterial cellulose membranes can be successfully used as substrate in flexible organic optoelectronic devices. (C) 2008 Elsevier B.V. All rights reserved.

Caracterização e aplicação da Blenda PEDOT : PSS/PVA na construção de eletrodos transparentes e dispositivos eletroluminescentes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Preparation and characterization of LiNi0.8Co0.2O2/PANI microcomposite electrode materials under assisted ultrasonic irradiation

A preparation method for a new electrode material based on the LiNi0.8Co0.2O2/polyaniline (PANI) composite is reported. This material is prepared by in situ polymerization of aniline in the presence of LiNi0.8Co0.2O2 assisted by ultrasonic irradiation. The materials are characterized by XRD, TG-DTA, FTIR, XPS, SEM-EDX, AFM, nitrogen adsorption (BET surface area) and electrical conductivity measurements. PANI in the emeraldine salt form interacts with metal-oxide particles to assure good connectivity. The dc electrical conductivity measurements at room temperature indicate that conductivity values are one order of magnitude higher in the composite than in the oxide alone. This behavior determines better reversibility for Li-insertion in charge-discharge cycles compared to the pristine mixed oxide when used as electrode of lithium batteries. (c) 2005 Elsevier B.V. All rights reserved.

Preparation and study as positive electrode of Li0.33La0.56TiO3-PANI nanocomposite

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo das propriedades de fotogeração e transporte de portadores de cargas em dispositivos optoeletrônicos orgânicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Supramolecular organization-electrical properties relation in nanometric organic films

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Propriedades ópticas e elétricas de materiais híbridos de sílica/orgânico à base de GPTS:TEOS preparados pelo método sol-gel

Fabrication of optoelectronic devices requires the employment of at least one transparent electrode. Usually, commercially transparent electrodes have been made by deposition of indium tin oxide (ITO) films by RF-Sputtering technique. These commercial electrodes have sheet resistance of about 100 Ω/sq and optical transmittance of 77% at the wavelength of 550 nm. The poly(3,4-ethylenedioxythiophene):polystyrene-sulfonate (PEDOT:PSS) is an alternative material to fabricate transparent electrodes due to its high conductivity (about 600 S/cm) and solubility in water. Soluble conductive materials exhibits advantages for processing of electrode layers, however there is a disadvantage during devices fabrication once materials with the same solvent of the electrode material cannot be coated one over the other. Alternatively, organic/Silica hybrid materials prepared by sol-gel process allow producing bulks and films with high chemical durability. In order to obtain transparent electrodes with high chemical durability, we introduced a blended material comprising the high UV-VIS transparency of organic/Silica sol-gel material and a high conductivity polymer PEDOT:PSS. The organic/Silica sol was obtained using two different molar concentrations (1:1 and 4:1), of tetraethylorthosilicate (TEOS) and 3-glycidoxypropyltrimethoxysilane (GPTS). Amounts of PEDOT:PSS solutions were added to the sol material, resulting in different weight fractions of sol and polymer. G:T/P:P were deposit onto glass substrates by spray-coating. In order to perform electrical characterization of the blended material, gold electrodes were thermally evaporated onto the films. The electrical characterization was performed using a Keithley 2410 source/meter unity and the optical characterization, using a Cary50 UV-Vis spectrophotometer. The absorption coefficient and electric conductivity of the different compositions blends, as function of the PEDOT:PSS concentration, were...

Magnetic field release of trapped charges in poly(fluorenylenevinylene)s

We have measured the effect of an applied magnetic field on the current through thin films of two different organic conjugated polymers that have previously shown to exhibit magnetoresistance, poly(9,9-dioctyl-1,4-fluorenylenevinylene) and poly(9,9-dioctyl-2,7-fluorenylenevinylene). The results show that the magnetic field releases trapped charges from inside the material and enhances the current. We have also performed optical absorption experiments on these polymer films under applied voltage and magnetic field. The results show that the magnetic field produces a change in the optical absorption in the low-energy range associated with deep traps and only under conditions when these traps are likely charged. These two results provide a strong case for the release of trapped charges caused by the magnetic field as being the cause of the magneto resistance in these polymers and possibly in other organic materials where magnetoresistance was recently observed. (c) 2007 Elsevier B.V. All rights reserved.

Estudo da fotocapacitância em dispositivos MIS orgânicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Phenomenological model for the interpretation of impedance/admittance spectroscopy results in polymer light-emitting electrochemical cells

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização de diodos tipo Schottky fabricados com poli-o-metoxianilina em diversas temperaturas

Technological advances achieved during the twentieth century strongly boosted the scientific research in the area of condensed matter physics, especially in the study and development of new semiconductor materials. In the segment, the development of semiconducting polymers for application in electronic devices promotes the field of organic electronics...(Complete abstract click electronic access below)

Estudo, construção e caracterização de diodos orgânicos tipo Schttky

During the twentieth century the inorganic electronics was largely developed being present in various industrial equipment or household use. However, at the end of that century were verified electronic properties in organic compounds, giving rise to the field of organic electronics. Since then, the physical properties of elementary devices such as diodes and organic transistors have been studied. In this work was studied the properties of diode devices fabricated with a semiconductor polymer, the poly-o-methoxyaniline (POMA). Devices containing electrodes of Au and Al were fabricated with semiconductor polymer of different doping levels. We found that the rectifying behavior for the heterojunctions metal/polimer are reached only for high doping level (with conductivity greater than 1,77. 10-9 S / cm), which gives the devices characteristic of a Schottky diode. The rectifying behavior was observed for electric fields of low magnitude, below the operating field (~ 600 V/cm), while for electric field greater than 600 V/cm the a linear behavior I vs.V was obtained. We determined that this Ohmic behavior arises from the charge transport over the volume of the semiconductor material after the lowering of the metal/semiconductor barrier. In devices with weakly doped semiconductor, the electrical resistance of the volume becomes high and the process of charge transportation is dominated by the volume, for any intensity of the applied electric field

Thermal inkjet printing of copper tetrasulfonated phthalocyanine (CuTsPc) as a semiconducting layer on flexible MIS capacitors

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estrutura supramolecular de um derivado de perileno em filmes finos fabricados por evaporação térmica a vácuo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)