Correlation between API 50 CH and multiplex polymerase chain reaction for the identification of vaginal lactobacilli in isolates

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sand-water slurry erosion of API 5L X65 pipe steel as quenched from intercritical temperature

The objective of this study was to analyze the erosion of API 5L X65 pipe steel whose microstructure consisted of ferrite and martensite obtained by quenching from intercritical temperature (770 °C). Jet impingement tests with sand-water slurry were used. The changes in mechanical properties, caused by heat treatment carried out, did not induce changes in either the mechanism or erosion resistance. The erosion rate increased with angle of attack until 30° and later decreased until 90°. The microtexture of the eroded surfaces, at angles of attack of 30° and 90°, were similar for both conditions and were composed of craters and platelets at several stages of evolution. The erosion mechanism was by extrusion with the forming and forging of platelets.

Estudo das propriedades mecânicas de aços microligados produzidos por laminação controlada seguida de resfriamento acelerado para tubos API/DNV usado no projeto pré-sal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aumento da velocidade de soldagem para processo de arco submerso em juntas de um tubo de aço API X70

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização mecânica, microestrutural e avaliação da fragilização pelo hidrogênio em tubos de aço API 5L grau X65MS PSL2

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Google e infoespoliação: internet, informação e acumulação de capital

Pós-graduação em Ciências Sociais - FFC

Uso do Google mapas como recurso didático para mapeamento do espaço local por crianças do ensino fundamental I da cidade de Ouro Fino/MG

Pós-graduação em Geografia - IGCE

Ensino de geografia: utilização de recursos computacionais (Google Earth) no ensino médio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da tenacidade à fratura na região de transição dúctil-frágil dos aços API 5L X70 e X80 utilizando a metodologia da curva mestra

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Tecnologias de Informação e Comunicação no cotidiano dos adolescentes: enfoque no comportamento e na competências informacionais da geração Google

Introduction: Individuals born from the 1990’s to accompany technological change course and learn how to use the technological resources that have access before they even learn to read or write. In this sense, the literature considers the digital natives or even 'Google generation'. However, it has been questioned their skills to identify information needs and seeking and use of information in the most varied environments digital information available on the Web. Objectives: To characterize the behavior of information seeking in everyday life of a group of teenage students from a private school in Marilia, Sao Paulo. Methodology: A qualitative study with 30 adolescent students of a private school in Marilia, Sao Paulo. Data collection was accomplished at first by means of a questionnaire, based on the research of Hughes-Hussell and August (2007), containing questions about age, gender, hobbies and everyday tasks, and issues the use of computers and the internet, which allowed determination of the social, economic and cultural rights of respondents. Results: have focused on the use of Information and Communication Technologies (ICT) to search access and use information. It was suggested that the "Brotherhood of Informatics', an incentive for students to (re) learn the tools of digital communication and make appropriate use of the resources, products and services on the web to search and effective use of information compatible with their needs and that is tied to the ethical and responsible use of technology environments. Conclusions: The results arising from this study will continue through the continuation of the Confraternity of Computing, which became a "thermometer" on the use of digital information environments and the attitude of the students in front of Information and Communication Technologies in the College “Cristo Rei”.

Avaliação da integridade estrutural em um tubo de aço API 5L X70 através da propagação de trincas por fadiga

Pós-graduação em Engenharia Mecânica - FEG

Avaliação da tenacidade CHARPY-V de um tubo de aço API 5L X70 soldado com arco submerso

This research project focused primarily on assessing the impact toughness of the weld and the base material of a steel pipe API 5L X70 submerged arc welded, used to conduct remote oil and gas (linepipes). The analysis followed strictly the Specification for Line Pipe - API 5L Standard, regarding the removal of the specimens of regions-of-proof-long section of the pipe, at 90o and 180o from the welded joint, and mechanical properties of toughness and Charpy-V, both the joint welded as the base material. Specimens of steel tube supplied by Tenaris Confab-SA were sized for tensile and Charpy-V, according to ASTM E 8M and ASTM E23, respectively. The result obtained showed that the API X70 steel tube has high Charpy-V toughness, near to each other at both 90o and 180o from the welded joint of the tube, and both higher than the weld metal. Microstructural and microhardness analysis complemented the present study

Determinação experimental da tenacidade à fratura em baixas temperaturas de tubos de aço API 5L X70

Because of the great metallurgical advances, the welded tubes by HF / ERW (High Frequency / Electrical Resistance Welding) have played a more active role in the oil and gas, gradually replacing tubes produced by other processes (UOE, SAW, and others) to deep water applications, in high and extremely low temperatures, highpressure conditions and in highly corrosive environments. However, studies have revealed that defects in the welded joints are in one of main causes of failures in pipelines. Associated with damage external and the stringent requirements of this sector, the welded joints become particularly critical for his toughness and the determination of this particular property is fundamental. This study aims to evaluate the toughness of the HF / ERW pipes in HSLA steel API X70 class, used in pipelines transport systems of gas and oil from data obtained with CTOD tests (Crack Tip Opening Displacement). The main objectives of this project are: mechanical and microstructural characterization of steels API X70 manufactured in Brazil; and evaluation of the toughness of weld process by HF / ERW steel API X70 national. After having the tests done, mechanical, chemical and metallurgical, we have the conclusion that those pipe are in agreement to API 5L 42ª edition for X70MO and the toughness behaves like the expected

Investigação experimental da tenacidade em tubos de aço API 5L X70 soldados pelo processo HF/ERW

Studies about structural integrity are very important when it desires to prevent disasters associated with flaws inherent in materials used in structural components. The welded joints in steel pipes used to conduction and distribution of oil and gas correspond to the regions most susceptible to flaw. Aiming to contribute to this research line, the present study was designed to assess experimentally the structural integrity of welded joints in steel pipes API 5L X70 used in pipeline systems. This assessment is given from tests of CTOD, whose aim is simulate in laboratory the real behaviour of crack from of his propagation on the welded joint obtained by high frequency electric resistance welding. In this case, the analyses are performed from specimens SE(B) obtained directly of steel pipe API 5L X70. The proposed methodology involves tests of CTOD at lower temperature, in order to assess the toughness of material in critical operation conditions. From performance of CTOD tests, was possible assess the toughness of welded joints in terms of quantity through CTOD parameter and in terms of quality from behaviour of curve load versus CMOD. In this study, also, sought to compare CTOD’s results obtained through rules ASTM E1820 (2008) and BS 7448 (1991). Although the two standards cited previously have adopted different parameters to calculated the value of CTOD, concluded that the values of CTOD tend to converge for a common value