Transient flow of the oil-refrigerant mixture through the radial clearance in rolling piston compressors

Unsteady flow of oil and refrigerant gas through radial clearance in rolling piston compressors has been modeled as a heterogeneous mixture, where the properties are determined from the species conservation transport equation coupled with momentum and energy equations. Time variations of pressure, tangential velocity of the rolling piston and radial clearance due to pump setting have been included in the mixture flow model. Those variables have been obtained by modeling the compression process, rolling piston dynamics and by using geometric characteristics of the pump, respectively. An important conclusion concerning this work is the large variation of refrigerant concentration in the oil-filled radial clearance during the compression cycle. That is particularly true for large values of mass flow rates, and for those cases the flow mixture cannot be considered as having uniform concentration. In presence of low mass flow rates homogeneous flow prevail and the mixture tend to have a uniform concentration. In general, it was observed that for calculating the refrigerant mass flow rate using the difference in refrigerant concentration between compression and suction chambers, a time average value for the gas concentration should be used at the clearance inlet.

Distortional buckling of simple lipped channel in bending results of the experimental analysis versus direct strength methods

Cold-formed steel members are subject to failure caused by buckling, normally under loads smaller than those corresponding to partial or total yielding of the cross section. The buckling of members in bending can be classified as local or global, and the occurrence of one or the other type is expected by the members' geometric characteristics and by the constraints and load conditions. One of the local instability modes that can characterize a member's failure is distortional buckling of the cross section occurring on its own plane and involving lateral displacements and rotations. This paper presents and discusses the procedures and results obtained from experimental tests of cold-formed steel members under bending. Forty-eight beams were carried out on members in simple lipped channel, in pairs, with 6-meter spans and loads applied by concentrated forces at every 1/3 of the span. The thickness, width and dimensions, of the stiffeners were chosen so that the instability by distortion buckling of the cross section was the principal failure mode expected. The experimental results are compared with the obtained results by using the direct strength method.

Recuperação de pastagem de Brachiara decumbens degradada com a introdução de estilosantes campo grande

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Métodos analíticos, numéricos e experimentais para o cálculo de ondas de impacto em meios líquidos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito dos parâmetros de pulso sobre as características geométricas e desempenho da soldagem com arame tubular autoprotegido e corrente pulsada

Pós-graduação em Engenharia Mecânica - FEB

Atributos químicos do solo, reservas orgânicas e sistema radicular de pastos degradados associada à introdução de leguminosa

The aim was to study the recovery of degraded pasture with the introduction of Stylosanthes macrocephala e capitata cv. Campo Grande on Brachiaria decumbens cv. Basilisk evaluating the levels N-total in roots, biomass, area, and length, diameter and root levels of macro and micronutrients in the soil. The experiment was conducted in the municipality of Andradina, Sao Paulo State, Brazil. The experimental design was a randomized block design in a split-plot (with and without phosphorus), with four replicates, forming the following treatments: control Brachiaria decumbens (CB), partial desiccation with 1.5 L ha(-1) of glyphosate (DP), total desiccation with 3.0 L ha(-1) of glyphosate (TD); tillage (T), soil scarification (S); harrowing rome (H) and plowing + disking (PD). Treatments H and PD were sown by broadcasting and the other in the form of direct seeding. Recovery strategies of grazing signal grass showed significant differences between treatments only for the content of N-total, there were no differences in geometric characteristics of roots and root biomass. The contents of macro and micronutrients in the soil showed no significant differences between the strategies of recovery. Fertilization had a significant effect for P. The introduction of estilosantes Campo Grande accompanied by techniques such as drying and plowing + disking contributed to increases in the N-total levels in the root system. Forms of introduction of legumes did not change the soil chemical properties.

Simetria no ensino fundamental através da resolução de problemas: possibilidades para um trabalho em sala de aula

This paper presents an alternative way of working with the theme of symmetry in the elementary school classroom. The proposal is based on qualitative research developed in the Professional Masters degree program in Science and Mathematics Teaching. We conducted field-work consisting of applying a sequence of activities for students in the seventh grade. The sequence was developed from the perspective of mathematics teaching using problem solving, taking into consideration aspects relevant to the study of geometry, such as intuition and visualization. In carrying out the activities, the dialogues between students and teacher were recorded and later transcribed. For data analysis we used the procedures of phenomenology. When interpreting the data, we observed that the teaching of symmetry using problem-solving enhances learning. We also found that, in an investigative environment, students are able to identify properties, argue about the geometric characteristics, and justify their opinions.

Contribuição metodológica ao estudo da dissecação e energia do relevo: proposta e avaliação de técnicas computacionais

Pós-graduação em Geociências e Meio Ambiente - IGCE

Improved geometric parameterisation techniques for continuation power flow

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

An efficient geometric parameterization technique for the continuation power flow

Continuation methods have been shown as efficient tools for solving ill-conditioned cases, with close to singular Jacobian matrices, such as the maximum loading point of power systems. Some parameterization techniques have been proposed to avoid matrix singularity and successfully solve those cases. This paper presents a new geometric parameterization scheme that allows the complete tracing of the P-V curves without ill-conditioning problems. The proposed technique associates robustness to simplicity and, it is of easy understanding. The Jacobian matrix singularity is avoided by the addition of a line equation, which passes through a point in the plane determined by the total real power losses and loading factor. These two parameters have clear physical meaning. The application of this new technique to the IEEE systems (14, 30, 57, 118 and 300 buses) shows that the best characteristics of the conventional Newton's method are not only preserved but also improved. (C) 2006 Elsevier B.V. All rights reserved.

The first frequency of cantilevered bars with geometric effect: a mathematical and experimental evaluation

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)