Assessing the surface roughness of a posterior resin composite: effect of surface sealing

This study assessed the in vitro influence of surface sealing on the surface roughness of a posterior resin composite before and after tooth-brushing. Thirty. specimens (13 nun diameter x 1 mm high) were fabricated from Filtek-P60 resin composite and randomly assigned to three groups (n=10): a non-sealed control and two groups sealed with one of the tested materials-a surface-penetrating sealant (Protect-it!-PI) and a one bottle adhesive system (Single Bond-SB). The samples were subjected to a surface roughness reading to determine the initial roughness, then submitted to simulated toothbrushing with 35,600 cycles for 100 minutes. Specimens were then cleaned and a post-abrasion surface roughness reading accomplished. Means (pm), recorded before (B) and after (A) toothbrushing, and standard deviations were: Control-(B): 0.032 (+/-0.005), (A): 0.054 (+/-0.005); PI-(B): 0.034 (+/-0.005), (A): 0.060 (+/-0.034); SB (B): 0.031 (+/-0.004), (A): 0.047 (+/-0.007). Data were tabulated and submitted to two-way ANOVA. No statistically significant difference was observed when the control and experimental groups were compared. However, a significant difference (p<0.05) was found between the measurements performed before and after toothbrushing. Based on these results, it may be concluded that using either a surface penetrating sealant or a one bottle adhesive system did not provide the optimization of superficial integrity. The use of a dentifrice and toothbrush resulted in significant alterations to the surface smoothness of the resin composite.

Assessing the effects of vector control on dengue transmission

The dengue virus is an arbovirus transmitted to humans through mosquito Aedes aegypti. To describe the dynamics of dengue disease within these two populations we develop a compartment model taking into account chemical controls and mechanical control applied on the mosquitoes, which are the currently available controlling mechanisms to prevent dengue disease. To mimic seasonal variations, some parameters of the model are allowed to depend on time in order to divide a calendar year in favorable and unfavorable periods regarded to the development of vector population. (c) 2007 Elsevier B.V. All rights reserved.

ASSESSING THE SUITABILITY of STERILE INSECT TECHNIQUE APPLIED TO AEDES AEGYPTI

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Assessing the role of vertical leaves within the photosynthetic function of Styrax camporum under drought conditions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Adaptation of the reservoir fish assemblage index (RFAI) for assessing the Barra Bonita Reservoir (São Paulo, Brazil)

In order to evaluate the environmental condition of the Barra Bonita Reservoir, we adapted the Index of Biotic Integrity (IBI). We chose 24 sampling sites in which three types of habitats were sampled: the mouths of tributaries, the central reservoir and the lateral reservoir. Fish were caught in two seasons (dry and rainy) using 10 gillnet gangs, with meshes ranging from 3 to 12 cm between opposite knots, and funnel traps. Abiotic and biotic variables were measured. Due to the artificial nature of the reservoir, the term biotic integrity was considered inappropriate and the term RFAI (Reservoir Fish Assemblage Index) was adopted. Twelve metrics from sixteen possibles were selected using the Pearson correlation coefficient. The reference conditions were set up based on the criteria of the best condition observed. For each metric, a score of 1, 3 or 5 was assigned as it strongly departs (1), slightly departs (3) or approaches (5) the reference condition. The index value is the sum of the metrics partial scores and ranges from 12 to 60. To evaluate the importance of the unit of measurement of the metric, the index was calculated in fish number (RFAI(N)) and in weight (RFAI(w)). The correlation between RFAIN and RFAIw was very high (r = 0.90, n = 46) indicating that the unit of measurement does not influence the final result of the index. Most of the sampling sites were classified in the 'reasonable' RFAI category. Only the central sites were classified as 'poor'. To validate the RFAI, another index, the Habitat Quality Index (HQI), was built starting from the physiochemical and habitat variables collected. The correlation of the RFAI with the HQI was highly significant (RFAIN, r = 0.37; RFAI(w), r = 0.47; n = 46), indicating that they respond in the same way to environmental degradation. The HQI metrics which most affect RFAI were depth, surrounding landscape and macrophyte presence/absence. Copyright C) 2007 John Wiley & Sons, Ltd.

Phylogenetic position of Dendropsophus gaucheri (Lescure and Marty 2000) highlights the need for an in-depth investigation of the phylogenetic relationships of Dendropsophus (Anura: Hylidae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Bayesian approach for assessing the stability of genotypes

Several statistical models can be used for assessing genotype X environment interaction (GEI) and studying genotypic stability. The objectives of this research were to show how (i) to use Bayesian methodology for computing Shukla's phenotypic stability variance and (ii) to incorporate prior information on the parameters for better estimation. Potato [Solanum tuberosum subsp. andigenum (Juz. & Bukasov) Hawkes], wheat (Triticum aestivum L.), and maize (Zea mays L.) multi environment trials (MET) were used for illustrating the application of the Bayes paradigm. The potato trial included 15 genotypes, but prior information for just three genotypes was used. The wheat trial used prior information on all 10 genotypes included in the trial, whereas for the maize trial, noninformative priors for the nine genotypes was used. Concerning the posterior distribution of the genotypic means, the maize MET with 20 sites gave less disperse posterior distributions of the genotypic means than did the posterior distribution of the genotypic means of the other METs, which included fewer environments. The Bayesian approach allows use of other statistical strategies such as the normal truncated distribution (used in this study). When analyzing grain yield, a lower bound of zero and an upper bound set by the researcher's experience can be used. The Bayesian paradigm offers plant breeders the possibility of computing the probability of a genotype being the best performer. The results of this study show that although some genotypes may have a very low probability of being the best in all sites, they have a relatively good chance of being among the five highest yielding genotypes.

Assessing the uncertainties of model estimates of primary productivity in the tropical Pacific Ocean

Depth-integrated primary productivity (PP) estimates obtained from satellite ocean color-based models (SatPPMs) and those generated from biogeochemical ocean general circulation models (BCGCMs) represent a key resource for biogeochemical and ecological studies at global as well as regional scales. Calibration and validation of these PP models are not straightforward, however, and comparative studies show large differences between model estimates. The goal of this paper is to compare PP estimates obtained from 30 different models (21 SatPPMs and 9 BOGCMs) to a tropical Pacific PP database consisting of similar to 1000 C-14 measurements spanning more than a decade (1983-1996). Primary findings include: skill varied significantly between models, but performance was not a function of model complexity or type (i.e. SatPPM vs. BOGCM); nearly all models underestimated the observed variance of PR specifically yielding too few low PP (< 0.2 g Cm-2 d(-1)) values; more than half of the total root-mean-squared model-data differences associated with the satellite-based PP models might be accounted for by uncertainties in the input variables and/or the PP data; and the tropical Pacific database captures a broad scale shift from low biomassnormalized productivity in the 1980s to higher biomass-normalized productivity in the 1990s, which was not successfully captured by any of the models. This latter result suggests that interdecadal and global changes will be a significant challenge for both SatPPMs and BOGCMs. Finally, average root-mean-squared differences between in situ PP data on the equator at 140 degrees W and PP estimates from the satellite-based productivity models were 58% lower than analogous values computed in a previous PP model comparison 6 years ago. The success of these types of comparison exercises is illustrated by the continual modification and improvement of the participating models and the resulting increase in model skill. (C) 2008 Elsevier BY. All rights reserved.

Assessing the above-ground biomass of a complex tropical rainforest using a canopy crane

Current estimates of the total biomass in tropical rainforests vary considerably; this is due in large part to the different approaches that are used to calculate biomass. In this study we have used a canopy crane to measure the tree architectures in a 1 ha plot of complex mesophyll vine forest at Cape Tribulation, Australia. Methods were developed to measure and calculate the crown and stem biomass of six major species of tree and palm (Alstonia scholaris (Apocynaceae), Cleistanthus myrianthus (Euphorbiaceae), Endiandra microneura (Lauraceae), Myristica insipida (Myristicaceae), Acmena graveolens (Myrtaceae), Normanbya normanbyi (Arecaceae)) using the unique access provided by the crane. This has allowed the first non-destructive biomass estimate to be carried out for a forest of this type. Allometric equations which relate tree biomass to the measured variable 'diameter at breast height' were developed for the six species, and a general equation was also developed for trees on the plot. The general equation was similar in form to equations developed for tropical rainforests in Brazil and New Guinea. The species equations were applied at the level of families, the generalized equation was applied to the remaining species which allowed the biomass of a total of 680 trees to be calculated. This has provided a current estimate of 270 t ha-1 above-ground biomass at the Australian Canopy Crane site; a value comparable to lowland rainforests in Panama and French Guiana. Using the same tree database seven alternative allometric equations (literature equations for tropical rainforests) were used to calculate the site biomass, the range was large (252-446 t ha-1) with only three equations providing estimates within 34 t ha-1 (12.5%) of the site value. Our use of multiple species-specific allometric equations has provided a site estimate only slightly larger (1%) than that obtained using allometric equations developed specifically for tropical wet rainforests. We have demonstrated that it is possible to non-destructively measure the biomass in a complex forest using an on-site canopy crane. In conjunction the development of crown maps and a detailed tree architecture database allows changes in forest structure to be followed quantitatively. © 2007 Ecological Society of Australia.

The need of subsidy for the implementation of photovoltaic solar energy as supporting of decentralized electrical power generation in Brazil

The growing demand for electrical power and the limited capital invested to provide this power is forcing countries like Brazil to search for new alternatives for electrical power generation. The purpose of this paper is to present a technical and economic study on a 15 kW solar plant installed in an isolated community, highlighting the importance of the need for financial subsidy from the government. It evaluates the importance of parameters such as the annual interest rate, specific investment, the marginal cost of expanding the electrical power supply and the government subsidy on amortization time of capital invested. © 2012 Elsevier Ltd All rights reserved.

Assessing the impact of menopause on salivary flow and xerostomia

Background: The aim of this study was to evaluate the symptoms of dry mouth and salivary flow in menarche and menopausal women. Methods: Objective and subjective assessment of salivary function were analysed by Xerostomia Inventory and Visual Analogue Scale questionnaire in menopausal and menarche women (control group). Salivary flow was evaluated by a chemical absorption stimulation test. Each subject provided three saliva samples: S1, non-stimulated saliva; S2, saliva initially stimulated with two drops of citric acid 2.5%; and S3, saliva super-stimulated with two drops of citric acid 2.5% every 30 seconds for two minutes. Results: No intergroup association was observed between Xerostomia Inventory and Visual Analogue Scale questionnaire. In both groups, the salivary flow was greatest at S3, followed by S2 and finally S1. Salivary flow was lower in the menopausal group compared to the control group only in S2 and S3. Conclusions: In the menopausal group, the salivary flow showed reduction but without clinical symptoms of dry mouth. It is important to normalize salivary flow to prevent oral abnormalities and maintain oral health. © 2013 Australian Dental Association.

Assessing the replacement of lead in solders: effects on resource use and human health

Human health and environmental concerns are not usually considered at the same time. Tin-lead solders are still widely used in several countries, including Brazil, by manufacturers of electronic assemblies. One of the options to reduce or eliminate lead from the manufacturing environment is its replacement with lead-free alloys. This paper applies emergy synthesis and the DALY indicator (Disability Adjusted Life Years) to assess the impact of manufacturing soft solder using tin, lead and other metals on the environment and on human health. The results are presented together with the company's financial results and the results calculated from the Brazilian statistical value of life. The calculation of emergy per unit showed that more resources are used to produce one ton of lead-free solders than to produce one ton of tin-lead solders, with and without the use of consumer waste recovered through a reverse logistics system. The assessment of air emissions during solder production shows that the benefits of the lead-free solution are limited to the stages of manufacturing and assembling. The tin-lead solder appears as the best option in terms of resource use efficiency and with respect to emissions into the atmosphere when the mining stage is included. A discussion on the influence of the system's boundaries on the decision-making process for materials substitution is presented. (C) 2012 Elsevier Ltd. All rights reserved.