Sudden changes in chaotic attractors and transient basins in a model for rattling in gearboxes

We consider a model for rattling in single-stage gearbox systems with some backlash consisting of two wheels with a sinusoidal driving; the equations of motions are analytically integrated between two impacts of the gear teeth. Just after each impact, a mapping is used to obtain the dynamical variables. We have observed a rich dynamical behavior in such system, by varying its control parameters, and we focus on intermittent switching between laminar oscillations and chaotic bursting, as well as crises, which are sudden changes in the chaotic behavior. The corresponding transient basins in phase space are found to be riddled-like, with a highly interwoven fractal structure. (C) 2004 Elsevier Ltd. All rights reserved.

Stepping-motor-driven constant-shear-rate rotating viscometer

Despite the frequent use of stepping motors in robotics, automation, and a variety of precision instruments, they can hardly be found in rotational viscometers. This paper proposes the use of a stepping motor to drive a conventional constant-shear-rate laboratory rotational viscometer to avoid the use of velocity sensor and gearbox and, thus, simplify the instrument design. To investigate this driving technique, a commercial rotating viscometer has been adapted to be driven by a bipolar stepping motor, which is controlled via a personal computer. Special circuitry has been added to microstep the stepping motor at selectable step sizes and to condition the torque signal. Tests have been carried out using the prototype to produce flow curves for two standard Newtonian fluids (920 and 12 560 mPa (.) s, both at 25 degrees C). The flow curves have been obtained by employing several distinct microstep sizes within the shear rate range of 50-500 s(-1). The results indicate the feasibility of the proposed driving technique.

Desenvolvimento de um sistema de análise de imagem para quantificação do tamanho e distribuição de partículas de desgaste

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Projeto mecânico do sistema de transmissão de um veículo Baja

This study aims to determine the best configuration for the new gearbox of the new Baja´s vehicle from Piratas do Vale team, focusing on the gear train, in order to achieve high performance of it. To this end, first some information about the vehicle is gathered to determine the best pair of gears configuration, then calculations about maximum bending stress, fatigue and surface thereof are performed; ; thereafter static simulations are performed using an a appropriated software. Thus this paper shows a satisfactory design of the addressed, besides providing the Baja SAE team consultation material for future use in the project

Uma análise da eficiência de uma transmissão CVT

This undergraduate thesis evaluates the effects of temperature variation of the air inside the CVT gearbox on the performance of a Continuously Variable Transmission (CVT). The CVT used in the tests was manufactured by Gaged Engineering (GX9 model) and is currently used in a Baja prototype. It’s a mechanically operated CVT, which the movement of the pulley plates varies according to the drive shaft rotation, shifting the belt along the diameter, and varying the transmission ratio. The purpose of this work is to analyze the change in the slip factor, coefficient that compares the variation between the actual transmission ratio and the ratio of geometric transmission, and its correlation with the power variation. A test bench was built and some tests were performed, indicating that was possible to achieve output power ratios of 1.75 [ℎ

Projeto mecânico de um redutor de engrenagens sem-fim numa esteira transportadora inclinada

This work aims to present the design and development of a speed reducer worm gear that will be implemented on an inclined treadmill that aims to raise the load below the top floor. The project start was made with research on issues related to mechanisms and machine elements, and these theories of fundamental importance in the development of device components, along with the help of SolidWorks software that was used to model the main parts of the project and Microsoft Office Excel 2007 was used to alight formulas to perform calculations of the project. All data for calculations were taken from the conditions of the problem to be solved in the best possible way the proposed problem (lifting load from the belt). Following the entire sequence of design gearbox assembly, beginning in pre-sizing and endless selection of electric motor, which consists of an iterative project, then scaling the worm gear and crown, shafts, splines, calculation and bearing selection

Desenvolvimento de uma caixa de redução para veículo Baja SAE

A gear Box in a Baja SAE vehicle is required due to the objectives of the SAE competitions, which the vehicles are challenged to pass through different obstacles. A powertrain system has as the main objective the extension of the torque for the traction shaft of the vehicle, when compared to that one available in the engine. The Objective of this thesis is the description of a gear box project for a Baja SAE vehicle of the Piratas do Vale Team of Unesp Guaratinguetá. In the development of the thesis, a flowchart, developed by the team, was used, which includes a theory part and also the choice of shelf components. In this Project, the type of gearbox was chosen, besides the calculation of axles, gears, bearings and sealers, and software simulations were done for the critical parts. The transmission, developed in this thesis, is more complex than the current one used by the team, but the new one shows improvements, as a new reverse gear with high torque

Concepção de um dispositivo fisioterápico: parapodium mecanizado

This paper presents a proposal to redesign a physical therapy device for patients with quadriplegia, called parapodium. With the help of the Association of Parents and Exceptional Friends of Guaratinguetá, it was possible to know the currently used device and from this it was conceived changes, allowing the increase of freedom of its central portion, in the down and across positions with mechanical drive . This adaptation is to introduce improvements in the routine of physical therapy professionals and reduce ergonomic problems resulting from repetitive strain during the transfer of patients to the parapodium. In addition to providing greater security for patients who require the use of this equipment. The proposed device comprises: wheel, gearbox and brake systems used for actuation, allowing a degree of turning of the rear post, along an axis which is fixed to the gearbox and the rear structure that permits posterior movement. The mechanism allows the rear post rotate from 0 ° to 90 °. The estimated cost to make the proposal is lower than the marketed parapodiuns, reaching the device's functional expectations