Model to design drip hose lateral line using two spacing between emitters

The use of non-pressure compensating drip hose in horticultural and annual cycle fruits is growing in Brazil. In this case, the challenge for designers is getting longer lateral lines with high values of uniformity. The objective of this study was to develop a model to design longer lateral lines using non-pressure compensating drip hose. Using the developed model, the hypotheses to be evaluated were: a) the use of two different spacing between emitters in the same lateral line allows longer length; b) it is possible to get longer lateral lines using high values of pressure variation in the lateral lines since the distribution uniformity stays below allowable limits. A computer program was developed in Delphi based on the model developed and it is able to design lateral lines in level using non-pressure compensating drip hose. The input data are: desired distribution uniformity (DU); initial and final pressure in the lateral line; coefficients of relationship between emitter discharge and pressure head; hose internal diameter; pipe cross-sectional area with the dripper; and roughness coefficient for the Hazen-Williams equation. The program allows calculate the lateral line length with three possibilities: selecting two spacing between emitters and defining the exchange point; using two pre-established spacing between emitters and calculating the length of each section with different spacing; using one emitter spacing. Results showed that the use of two sections with different spacing between drippers in the lateral line didn't allow longer length but got better uniformity when compared with lateral line with one spacing between emitters. The adoption of two spacing increased the flow rate per meter in the final section which represented approximately 80% of the lateral line total length and this justifies their use. The software allowed DU above 90% with pressure head variation of 40% and the use of two spacing between emitters. The developed model/software showed to be accurate, easy to handle and useful for lateral line design using non-pressure compensating drip hose.

Uso de Dois Espaçamentos Entre Gotejadores na Mesma Linha Lateral e Seus Efeitos Sobre a Formação do Bulbo Molhado no Solo e Parâmetros Físicos de Rabanete

The use of irrigation systems that consume lower water and energy in agriculture is important to supply the growing global demand for food. In this way, it's important to develop techniques that will increase the uniformity of water application on drip irrigation systems. The aim of the work was to compare the provision of lateral lines in drip irrigation, through the formation of wet bulbs in soil and physical parameters of radish, composed of single spacing between drippers in relation to lateral lines composed of two segments, each one composed by different spacing between emitters. Two distributions of evaluation were carried out: 1) conventional drip lateral lines with 20 cm emitter spacing were compared to proposed drip lines, with 24 emitter spacing in the initial section and 20 cm emitter spacing in the final section; 2) conventional drip lateral lines with 30 cm emitter spacing were compared to proposed drip lines, with 36 emitter spacing in the initial section and 30 cm emitter spacing in the final section. The experiment was carried out in a greenhouse of the Sao Manuel Experimental Farm, located at Sao Manuel, SP. The experimental design was entirely randomized, with six treatments and four replications. Results showed no difference among treatments for the most of the evaluated variables. So it is possible to conclude that the use of different spacing between emitters in the same lateral line can be used to increase the line length.

Uso de dois espaçamentos entre gotejadores na mesma linha lateral e seus efeitos sobre a formação do bulbo molhado, produtividade e qualidade de rabanete (raphanus sativus L.)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo da uniformidade de emissão de água utilizando diferentes espaçamentos entre gotejadores na linha lateral

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Increasing the lateral line length of drip irrigation systems

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Breeding potential of maize composite Isanao VF1 in small spacing in the second growing season

The purpose of this study was to verify the breeding potential of the maize composite Isanao VF1 in the second growing season. One hundred and fifty half-sib progenies were evaluated of spacing of 0.45 m, densities of 57,778 and 80,000 plants ha(-1), in a randomized block design with three replications. Gains of 16.0 and 19.2% were estimated for grain Yield, H. I and 10.5% for prolificacy and 12.3 and 12.9% for ear height, respectively, at 57,778 and 80,000 plants ha(-1). The heritabilities for plant height, ear height and grain yield were 65.2 and 61.3%, 64.3 and 66.9% and 53.5 and 63.3%, respectively, confirming the potential for breeding at both densities. The absence of progeny by density interaction indicates that no further selection programs are necessary. The occurrence of segregation for modifier genes for height suggests stabilizing selection based on ear height.

Changes on emitter discharge under different water temperature and pressure

The study was conducted at the Research Laboratory of Hydraulic and Irrigation Group in the Rural Engineering Department, Technical University of Madrid (Universidad Politecnica de Madrid), Madrid, Spain. Water temperatures of 20, 30, 40 degrees C and system pressures often encountered in irrigation practices of 80, 90, 100, 110, 120, 130, 140, 150, 160, 170, 180, 190 and 200 k Pa were applied to determine the effects of different water temperatures and pressures on emitter discharge. Non-pressure compensating in-line emitter which has turbulent flow regime with a long-path (labyrinth), emitter discharge was 4 L h(-1) at system pressure of 100 kPa according to the manufacturer recommended, was used. Emitters were spaced 20 cm along the drip laterals with 16 mm diameter. Discharge equations and coefficients of variation related to temperatures of 20, 30 and 40 degrees C were obtained as q = 0.375H(0.51), q = 0.358H(0.52), q = 0.346H(0.53) and 2.68, 2.09, 3.65, respectively. Discharge of the emitter was affected by different system pressures and increased as potentially (R = 0993-0996). In general. the emitter discharge increased with increasing temperature. However, especially in the common system pressures of 90-120 k Pa, differences of obtained emitter discharges between the different water temperatures were not significant (1%).

Narrow row spacing and high plant population to short height castor genotypes in two cropping seasons

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of row spacing and intercrop on maize grain yield and forage production of palisade grass

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Plant spacing and pollen quantity on yield and quality of squash seeds

O rendimento e a qualidade de sementes de abóbora podem ser aprimorados por uma densidade populacional de plantas adequada, além da quantidade de pólen, que influi na qualidade da polinização e fertilização. Para este estudo, aplicaram-se nove tratamentos, que resultaram da combinação fatorial de três espaçamentos entre plantas (0,8 x 0,3; 0,8 x 0,6 e 0,8 x 0,9 m) com duas quantidades de pólen (50% de uma antera e uma antera inteira) e a polinização natural por insetos. Foram avaliados parâmetros de produção de frutos e sementes, além da qualidade física e fisiológica das sementes. O delineamento experimental adotado foi em blocos ao acaso com cinco repetições e dez plantas úteis por amostragem. O aumento do espaçamento entre plantas elevou o número médio de frutos maduros e a produção de sementes por planta. A produtividade de sementes foi diretamente proporcional à quantidade de pólen usada durante a polinização. Já o fator espaçamento entre plantas não afetou a produção de sementes por área. A maior quantidade de pólen resultou em uma maior produção de sementes por planta e por área. A polinização manual, com a utilização de uma antera inteira, não diferiu da polinização natural com insetos, tanto para rendimento como para a qualidade de sementes.

Productivity of lettuce and radish cultivations as a function of spacing and of time of establishment of intercropping

The experiment was conducted at UNESP, Jaboticabal-SP, during the period of September to November of 2000, with the objective of evaluating the productivity of the cultivation of lettuce and radishes as a function of spacing between plants and of the time of establishment of intercropping. The experimental design was a completely randomized blocks and four replications. The 14 treatments consisted of combinations of spacing between lines (0.30 and 0.40 m), cultivation systems (intercropping and monoculture), and time of sowing of radish seeds to establish intercropping (0, 7 and 14 days after transplant of lettuce). The cultivars of lettuce and radish were, 'Tainá' and 'Crimson Gigante', respectively. A greater yield of commercial radish roots was obtained with intercropping cultivation. The fresh mass of lettuce in monoculture did not differ from that produced with intercropping. These results suggest that intercropping cultivation between these species is advantageous.

Productivity of cherry tomatoes under protected cultivation carried out with different types of pruning and spacing

The aim of the study was to evaluate production and determine the level of total soluble solids for cherry tomatoes, under protected cultivation carried out with different types of spacing and pruning. The experiment was performed according to a randomized block design in a 2×2 factorial scheme, with two types of spacing between plants and two types of pruning, and with five repetitions. The cultivar 'Sindy' (De Ruiter) was utilized. Each experimental parcel contained seven plants, and fruits were collected from the five central plants. The seedlings were produced in Styrofoam trays of 128 cells and transplanted at 33 days after planting using two types of spacing between plants (0.3 and 0.5 m) and 1 m spacing between rows. The plants were grown as single-or double-stem form and staked individually. The parameters evaluated were the number of fruit per plant, fresh weight of fruit and the level of total soluble solids expressed in °Brix. There was no evidence of significant interaction between the treatments. For fresh weight of fruit per plant, there was a significant effect when the plants were grown with a spacing of 1 × 0.5 m, with 4.12 kg per plant, compared to a production of 3.00 kg per plant with a spacing of 1 × 0.3 m. With regard to the number of fruit per plant, a significant difference was seen between the two types of spacing, where a spacing of 1 × 0.3 m yielded a lower number of fruit per plant (188.8), compared to that observed with a spacing of 1 × 0.5 m (238.1). With regard to the two types of pruning, there was a significant effect for only the number of fruit per plant, where the mean number of fruit was 188.4 with one stem and 238.4 with two stems. No significant difference was observed between the treatments for the level of total soluble solids. It is concluded that for the cultivar 'Sindy', under protected cultivation, production is better with a spacing of 0.5 m between plants and the use of two stems per plant.

Forage mass production and grazing loss of sorghum hybrid in response to the density of the sowing and the spacing between planting lines

The objective of this experiment was to evaluate dry matter yield and loss of grazing due to animal trampling in response to sowing density and spacing between lines in the planting. Sorghum hybrid 1P400 was submitted to six treatments, composed of three sowing density combinations (12; 16 and 20 kg/ha of seeds) and two spacing between lines (0.40 and 0.80 m). Sorghum hybrid 1P400 was sowed in two seasons, at the end of spring (December 3rd, 2005) and the other at the end of summer (March 20th, 2006). Cultivation strategies influenced plant population in the two experimental seasons. Diameter of the stem in season 1 decreased with density increase, whereas in the second season, interaction between sowing density and spacing was significant. In the first season, 0.40-m spacing promoted greater losses due to grazing stepping, that is, 891 kg/ha of DM, whereas in the second season there was no statistical difference. There was no significant difference in forage dry matter yield in sowing densities among the two studied seasons. Dry mater production of sorghum hybrids 1P400 did not increase with the increase of the sowing density in the two sowing seasons, therefore it is recommended 12 kg/ha of seeds for the sowing. Sorghum IP400 cultivated in 0.80-m spacing resulted in lower forage loss caused by grazing bovine trampling. © 2011 Sociedade Brasileira de Zootecnia.

Biomass production and chemical composition of essential oil of Piper callosum as affected by spacing in Manaus, Amazonas State, Brazil

The family Piperaceae contains nearly 2000 species, most of them distributed in two genera, Piper and Peperomia. In Brazil circa 170 Piper species are found, mainly in tropical areas Their use ranges from flavoring and culinary to raw material for pharmaceutical and cosmetic industry. One of these species, Piper callosum, is used in folk medicine in the Amazon area. The objective of this study was to evaluate the production of biomass (aerial parts) as well as yield and composition of the essential oil from the leaves, according to different spacing between cultivated plants at Embrapa Western Amazon, in Manaus, State of Amazonas, Brazil. The experimental design was randomized blocks, with four treatments and seven replicates with six plants. Biomass production was inversely proportional to the spatial arrangements, with the greatest biomass production (1034.93 kg/ha) in the shortest spacing (E1), although no statistical difference was verified between E3 and E4. The same response was observed for the production of essential oil. The chemical composition of the oil was not affected by spacing, and major compounds found were safrole (59.1%), beta-pinene (8.3%), alpha-pinene (6.5%), methyl eugenol (6.3%) and 1,8-cineole (4.1).

Productivity characteristics of endive as a function of spacing

Endive (Cichorium intybus) is one of the vegetables least studied in Brazil with respect to the behavior of the most commercialized cultivars, but it is known that the number of plants per area is one of the factors that most influences the productivity of various crops. Thus, the objective of this work was to evaluate the behavior of endive using four spacings between rows and five spacings between plants, in the region of Jaboticabal-SP. The experiment was conducted in the field in the period of August 12, 2008 to November 6, 2008, in the experimental area of the Sector of Vegetable Crops and Aromatic-Medicinal Plants, Department of Crop Sciences, School of Agricultural and Veterinary Sciences - UNESP-FCAV. The experimental design utilized was a randomized block design with a 4 × 5 factorial scheme, i.e., four spacings between rows (0.15, 0.20, 0.25 and 0.30 m) and five spacings between plants (0.10, 0.15, 0.20, 0.25 and 0.30 m), with three repetitions. The endive cultivar studied was 'Pão-de-Acucar', obtained from the company Tecnoseed. Seedlings were established utilizing the sowing system in 200-cell Styrofoam trays containing the substrate Plantmax Vegetables® HA. The seedlings were transplanted at 37 days after planting. After harvesting, the following characteristics were determined: height (cm), diameter of the plant in rows (cm), diameter of the plant in between rows (cm), number of leaves, fresh weight (g) and total estimated productivity (t/ha). There were no interactions between the factors studied. Based on the data, we conclude that spacings of 0.15 m between rows and of 0.15 m between plants produce plants of higher quality and with greater productivity.