Determinação da circunferência de rolamento de pneus agrícolas utilizando dois métodos: manual e eletrônico

A circunferência de rolamento dinâmica dos pneus agrícolas é uma medida importante para o estudo do desempenho de tratores agrícolas. Neste trabalho, compararam-se dois métodos de determinação da circunferência de rolamento dinâmica - um manual e um eletrônico (com instrumentação das rodas de tração) - sob duas velocidades de deslocamento e cinco combinações de pressão de inflação nos pneus dianteiros e traseiros. O método manual forneceu valores estatisticamente superiores aos do eletrônico, com diferença absoluta máxima de 0,24%. A pressão de inflação influenciou significativamente os valores medidos, enquanto a velocidade de deslocamento, para os valores do ensaio (3,0 e 6,0 km.h-1), não apresentou influência significativa.

Desenvolvimento de um circuito eletrônico experimental de anemômetro de fio quente

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise e síntese de um processador digital wavelet

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de dispositivos computacionais para registro de dados pluviométricos e análise operacional de pluviômetros basculantes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Performance evaluation on electronic control systemsfor field sprayers using programmable logic controllers

The aim of this study was to develop a laboratory method for time response evaluation on electronically controlled spray equipment using Programmable Logic Controllers (PLCs). For that purpose, a PLC controlled digital drive inverter was set up to drive an asynchronous electric motor linked to a centrifugal pump on a experimental sprayer equipped with electronic flow control. The PLC was operated via RS232 serial communication from a PC computer. A user program was written to control de motor by adjusting the following system variables, all related to the motor speed: time stopped; ramp up and ramp down times, time running at a given constant speed and ramp down time to stop the motor. This set up was used in conjunction with a data acquisition system to perform laboratory tests with an electronically controlled sprayer. Time response for pressure stabilization was measured while changing the pump speed by +/-20%. The results showed that for a 0.2 s ramp time increasing the motor speed, as an example, an AgLogix Flow Control system (Midwest Technologies Inc.) took 22 s in average to readjust the pressure. When decreasing the motor speed, this time response was down to 8 s. General results also showed that this kind of methodology could make easier the definition of standards for tests on electronically controlled application equipment.

Sharpening of periodontal instruments with different sharpening stones and its influence upon root debridement--scanning electronic microscopy assessment

The objective of this study was to evaluate, through scanning electronic microscopy, the effect of sharpening with different sharpening stones on the cutting angle of periodontal curettes (Gracey 5-6), and the influence on root surfaces after debridement and planing. The experimental model consisted of two different phases. In the first, the cutting angles of fifteen stainless steel Gracey 5-6 curettes were analyzed under a scanning electronic microscope after being sharpened with different types of stones. In the second phase, the root surfaces of 25 newly extracted teeth were evaluated with a scanning electronic microscope after being debrided with curettes sharpened with different stones. Analysis of the results showed that the synthetic stones (aluminum oxide and carborundum) are more abrasive and produce more irregular cutting angles, whereas Arkansas stones are less abrasive and produce smoother and more defined cutting angles. There was no significant statistical differences among the five groups tested with regard to the degree of irregularity of the root surfaces after instrumentation.

Methodology analysis of a computational tool used in electronic circuit design

This paper considers the importance of using a top-down methodology and suitable CAD tools in the development of electronic circuits. The paper presents an evaluation of the methodology used in a computational tool created to support the synthesis of digital to analog converter models by translating between different tools used in a wide variety of applications. This tool is named MS 2SV and works directly with the following two commercial tools: MATLAB/Simulink and SystemVision. Model translation of an electronic circuit is achieved by translating a mixed-signal block diagram developed in Simulink into a lower level of abstraction in VHDL-AMS and the simulation project support structure in SystemVision. The method validation was performed by analyzing the power spectral of the signal obtained by the discrete Fourier transform of a digital to analog converter simulation model. © 2011 IEEE.